Flutter analysis of an airfoil with nonlinear damping using equivalent linearization

The equivalent linearization method （ELM） is modified to investigate the nonlinear flut- ter system of an airfoil with a cubic damping. After obtaining the linearization quantity of the cubic nonlinearity by the ELM, an equivalent system can be deduced and then investigated by linear flut- ter analysis methods. Different from the routine procedures of the ELM, the frequency rather than the amplitude of limit cycle oscillation （LCO） is chosen as an active increment to produce bifurca- tion charts. Numerical examples show that this modification makes the ELM much more efficient. Meanwhile, the LCOs obtained by the ELM are in good agreement with numerical solutions. The nonlinear damping can delay the occurrence of secondary bifurcation. On the other hand, it has marginal influence on bifurcation characteristics or LCOs.     

肋角度对气膜冷却特性的影响

在光滑二次流通道的基础上,分析对比了两种带肋通道(135°肋和45°肋)对气膜冷却特性的影响.采用瞬态液晶测试技术获得了气膜孔下游表面传热系数比与气膜冷却效率分布.使用Fluent软件RANS数值方法对相应结构进行了数值模拟,并使用了realizable k-ε湍流模型.光滑二次流通道模型中,气膜孔内流线呈螺旋状分布,导致较大的孔内速度分离与流动损失.冷气射流分成两部分,其中一股形成一对偏斜的对转涡.135°肋结构中,二次流通道上部分的旋转涡为顺时针方向,使得气流易于流入气膜孔,气膜孔内流线呈直线分布.45°肋结构中,二次流通道上部分旋转涡为逆时针方向,增强了气膜孔内旋转涡.45°肋结构中冷气流入气膜孔之后的流动结构与光滑二次流通道结构相似.135°肋结构气膜冷却效率最大而表面传热系数比最低.     

基于起落架参数设计的某直升机地面共振及参数影响分析

建立了某直升机地面共振分析力学模型,计算了起落架在桨毂中心处的等效刚度和阻尼,针对某直升机进行了地面共振分析,同时分析了摆振铰外伸量、质量静距、桨毂中心有效刚度等对地面共振的影响,为避免地面共振及参数改进提供依据。     

Stability analysis of an aeroelastic system with friction

In this paper, harmonic balance method, exact formulation and numerical simulation method are adopted to study the effects of different friction stiffness on the stability of 1.5 degrees of freedom aeroelastic system. On this basis, the expressions of input energy and dissipated energy are deduced, and the energy method is used to reveal the mechanisms of the stable boundary and unstable boundary existing in the system and the effects of different friction stiffness on the stability of the system. Studies have shown that the stability region and the critical aerodynamic damping ratio of the system rise with the increase of the friction stiffness, while the friction stiffness has little effect on the stability boundary. In the analysis of the stability of system, the results of harmonic balance method, exact formulation and Newmark of numerical simulation method are in good agreement. Compared with exact formulation and numerical simulation method, the concept and conclusion of harmonic balance method are simple in the system stability analysis.     

Keck observations of ROSAT ultra-luminous X-ray source candidates

We present results of optical follow-up observations of candidate ultra-luminous X-ray sources (ULXs). Using Keck optical spectroscopy, 17 of the candidates from the Colbert and Ptak [Colbert, E.J.M., Ptak, A.F. A catalog of candidate intermediate-luminosity X-ray objects. ApJS 143, 25–45, 2002] catalog have been identified; this is one of the largest sets of optical identifications of such objects thus far. Fifteen are background active galactic nuclei (AGN); two are foreground stars in our Galaxy. These findings are consistent with background and foreground object expectations, as derived from log N–log S relations. Also, the results are briefly discussed in terms of the spiral-galaxy/ULX connection.     

航空带垫卡箍刚度及阻尼特性分析与试验验证

研制了带垫卡箍刚度测试装置,分别对不同规格卡箍线刚度和扭转刚度进行了测量,并将卡箍刚度测量数值引入卡箍-管路系统有限元模型,通过管路固有特性数值计算与试验测试结果对比,误差在5％左右,验证了卡箍刚度参数的准确性.进一步搭建了卡箍阻尼测量系统,通过测量卡箍动态传递率,获得相对应的模态阻尼比,并将卡箍阻尼测量数值引入卡箍-...     

延伸冲击孔冲击冷却流动与换热特性的数值研究

采用数值模拟方法研究了延伸冲击孔冲击冷却系统的冷却特性,分析了3个冲击雷诺数和5个冲击孔延伸长度对冲击腔内流动与换热特性的影响,给出了靶面努塞尔数分布、靶面压力分布、中心截面流速与综合换热性能的变化。结果表明：延伸冲击孔可以有效地防止横流对冲击射流的偏转作用,同时使射流出口更加贴近冲击靶面壁面,冲击速度更高,可以明显提高靶面的换热系数,并使整个靶面上的换热系数分布也更加均匀。冲击冷却的冷却性能随着冲击孔延伸长度的增加而增加,相较于传统冲击冷却（baseline）,在L/d=2.5时靶面平均努塞尔数提升达15%以上,但压力损失也相对较高;对比不同延伸长度冲击孔的综合换热性能,发现存在最佳的L/d取值范围使冲击冷却系统获得最佳的综合冷却性能。在本研究范围内,最佳的L/d= 2.5。     

基于实验复模态参数的有限元模型修正

提出了一种利用非完备实验复模态参数,修正带有非比例阻尼矩阵结构有限元模型的迭代修正方法。首先,对处理困难的阻尼矩阵表达为质量与刚度矩阵的多项式组合,并给出了物理解释,被修正参数为该多项式的系数和结构的某些局部几何、材料参数,其修正结构物理意义明确,与结构的动态设计相适应,实例表明了本文修正方法的有效性。     

短裂纹的裂纹尺寸分布密度函数与耐久性设计

给出了一个极为简单的近似方法, 只要依据亚音速机翼在t-= 0 时的f Ej i ( 0) 和t-= ts 时的 f Eij ( t-s) 值即可求得非定常空气动力系数的两个主导极点值, 避免了必须先计算出机翼的任一个气 动力系数指数函数, 然后经过拟合才能求出两个主导极点值的繁琐作法。 关键词　非定常流, 机翼, 气动力系数, 指数函数.