关于进行程序管制一体化模拟练习的设想

在程序管制模拟练习中，存在着塔台管制服务、进近管制服务和区域管制服务互不衔接，不能系统地模拟整个管制过程的问题。针对这一情况提出了程序管制一体化模拟练习和程序和管制一体化模拟机的结构设计。     

ATM局域网仿真技术

简要介绍了 Ａ Ｔ Ｍ 局域网仿真的主要原理，以 Ｉ Ｂ Ｍ ８２６０ Ａ Ｔ Ｍ 交换机为例，具体分析了 Ａ Ｔ Ｍ 局域网仿真的实现细节。     

Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

Route generation and description using the notions of object's influence area and spatial conceptual map

In the GRAAD Project we aimed at creatinga system which could generate route directions thatare comparable to route directions created by humanparticipants. With this goal in mind, we started froma linguistic and cognitive study of route directionsproduced by people and the study of cognitive modelsof mental maps. We proposed a new qualitative spatialmodel that can support the spatial properties of humanroute directions. This model is based on the notion ofobject's influence area which is used to modelneighborhood, orientation and distance. The proposedapproach relies on the manipulation of spatialentities in a spatial conceptual map (SCM) which isthe computarized analog of a mental map used bypeople. We developped the GRAAD System, software thatgenerates routes in a SCM and describes them innatural language. Finally, we conducted an experimentin order to compare GRAAD's route directions androutes described by human participants in similarexperimental conditions. GRAAD's output was notdistinguishable from route directions created by humanparticipants. In this paper we present the mainresults obtained during all phases of the GRAADProject.     

低温氢气排放过程数值模拟

以低温氢气安全排放为目的,采用数值模拟方法对低温氢气直接排放和燃烧排放的流场进行分析.流场仿真计算采用了标准双方程k-ε湍流模型和氢氧单步燃烧模型.研究参数包括氢排放压力、流量、温度和环境风速,评价指标为氢扩散范围和燃烧范围.计算结果表明：燃烧排放燃烧范围小于直接排放氢扩散范围;排放压力增加、流量增大和温度降低均会使氢扩散范围和燃烧范围变大.     

一种大面积比喷管的分段式设计与数值分析

为了满足大推力上面级发动机大面积比喷管的设计需求,采用了排放冷却前段和单壁辐射冷却尾段的分段式设计方案。在排放冷却前段传热计算的基础上,通过对内流场进行数值模拟,重点研究了单壁尾段在引入上游排放冷却气氢情况下的冷却特性和喷管效率。结果表明:对于大面积比喷管,采用带二次流的单壁金属喷管延伸段是现实可行的,有望达到较好的冷却保护效果并提高喷管效率。     

含噪信号经验模式分解虚假分量识别方法

针对含噪信号Hilbert-Huang变换存在虚假分量,提出改进的奇异值分解(SVD)方法进行降噪,改进包含两个部分:一是利用重构相空间代替传统矩阵如Hankel矩阵,以去掉信号冗余,再者提出奇异值能量熵分量差分法,更易于定出重构奇异值阶次;二是提出了频谱比值法对虚假分量进行辨识,更有效辨识出虚假分量.首先利用经验模式分解(EMD)得到本征模式分量(IMF),识别并剔除趋势项,重构信号,然后进行SVD,重构降噪后的信号,消除虚假分量,最后进行时频分析.联合方法应用于含噪仿真信号,信噪比(signal noise ratio,SNR)提高了5.5%,虚假分量辨识率提高至100%,用于双跨转子故障振动信号,得到正确的时频结果,表明了所提方法识别含噪信号虚假分量的有效性.     

肋角度对气膜冷却特性的影响

在光滑二次流通道的基础上,分析对比了两种带肋通道(135°肋和45°肋)对气膜冷却特性的影响.采用瞬态液晶测试技术获得了气膜孔下游表面传热系数比与气膜冷却效率分布.使用Fluent软件RANS数值方法对相应结构进行了数值模拟,并使用了realizable k-ε湍流模型.光滑二次流通道模型中,气膜孔内流线呈螺旋状分布,导致较大的孔内速度分离与流动损失.冷气射流分成两部分,其中一股形成一对偏斜的对转涡.135°肋结构中,二次流通道上部分的旋转涡为顺时针方向,使得气流易于流入气膜孔,气膜孔内流线呈直线分布.45°肋结构中,二次流通道上部分旋转涡为逆时针方向,增强了气膜孔内旋转涡.45°肋结构中冷气流入气膜孔之后的流动结构与光滑二次流通道结构相似.135°肋结构气膜冷却效率最大而表面传热系数比最低.     

飞机下滑波束导引系统设计及仿真

下滑波束导引系统是飞机在自动着陆时所采用的一种重要无线电波束导引系统。首先,简要阐述了下滑波束导引系统的基本工作原理;然后,对导引系统的运动学环节及下滑耦合器进行分析,对飞机下滑波束导引系统结构进行设计;最后,在MATLAB平台下,对所设计的下滑波束导引系统进行大量仿真研究。仿真结果显示。所设计的下滑波束导引系统结构是合理的,其控制系统是稳定的,且其稳态性能也得到改善。     

某全机模型的水滴撞击特性分析

飞机结冰会对其飞行造成巨大隐患。应用Fensap软件,使用CFD计算方法,采用Spalart-Allmaras湍流模型对德国宇航中心(DLR)某型飞机的三维模型进行气动及水滴撞击特性分析。通过控制变量的方法,确定环境参量对水滴撞击特性的影响。结果表明:飞机速度增大,局部水收集系数减小;水滴直径减小,局部水收集效率也减小。