FGM板三维层合模型及热-噪声载荷下的动态响应研究

 为了有效地分析热-噪声联合载荷作用下的飞行器功能梯度壁板结构的非线性动态响应,提出了运用复合材料多层壳单元建立功能梯度材料(FGM)板的层合有限元建模新方法,研究了FGM板在热曲屈前、后状态下复杂的非线性时域动态响应特性,并探讨了梯度指数、热曲屈系数及声压级(SPL)等参数对FGM板非线性动态跳变响应的影响规律。FGM板三维层合建模新方法避免了采用常规有限元法(FEM)建模时需要在厚度方向划分大量单元的缺点;求解FGM板非线性动态响应时采用的隐式积分方案避免了模态叠加法对参与模态选择的经验性要求及模态截断造成的信息丢失等缺陷。仿真结果表明:FGM板层合有限元建模新方法合理可行、过程简便、计算精度高;研究发现:陶瓷-金属FGM板在热屈曲后的抗声振性能并不像热屈曲前那样介于金属板和陶瓷板之间,而是表现最差;热屈曲系数及声压级的组合形式是导致FGM板发生非线性跳变响应的主要影响因素。     

An adaptive turbo-shaft engine modeling method based on PS and MRR-LSSVR algorithms

In order to establish an adaptive turbo-shaft engine model with high accuracy, a new modeling method based on parameter selection (PS) algorithm and multi-input multi-output recursive reduced least square support vector regression (MRR-LSSVR) machine is proposed. Firstly, the PS algorithm is designed to choose the most reasonable inputs of the adaptive module. During this process, a wrapper criterion based on least square support vector regression (LSSVR) machine is adopted, which can not only reduce computational complexity but also enhance generalization performance. Secondly, with the input variables determined by the PS algorithm, a mapping model of engine parameter estimation is trained off-line using MRR-LSSVR, which has a satisfying accuracy within 5&. Finally, based on a numerical simulation platform of an integrated helicopter/ turbo-shaft engine system, an adaptive turbo-shaft engine model is developed and tested in a certain flight envelope. Under the condition of single or multiple engine components being degraded, many simulation experiments are carried out, and the simulation results show the effectiveness and validity of the proposed adaptive modeling method.     

Research on failure criterion of composite based on unified macro- and micro-mechanical model

A new unified macro- and micro-mechanics failure analysis method for composite structures was developed in order to take the effects of composite micro structure into consideration. In this method, the macro stress distribution of composite structure was calculated by commercial finite element analysis software. According to the macro stress distribution, the damage point was searched and the micro-stress distribution was calculated by reformulated finite-volume direct averaging micromechanics (FVDAM), which was a multi-scale finite element method for composite. The micro structure failure modes were estimated with the failure strength of constituents. A unidirectional composite plate with a circular hole in the center under two kinds of loads was analyzed with the traditional macro-mechanical failure analysis method and the unified macro- and micro-mechanics failure analysis method. The results obtained by the two methods are consistent, which show this new method’s accuracy and efficiency.     

A method of multi-objective reliability tolerance design for electronic circuits

Tolerance design plays an important role in reliability design for electronic circuits. The traditional method only focuses on the consistency of output response. It is not able to meet the needs of increasing development of electronic products. This paper researches the state of related fields and proposes a method of multi-objective reliability tolerance design. The characteristics of output response and operating stresses on critical components are both defined as design objectives. Critical components and their operating stresses are determined by failure mode and effect analysis (FMEA) and fault tree analysis (FTA). Sensitivity analysis is carried out to determine sensitive parameters that affect the design objectives significantly. Monte Carlo and worst-case analysis are utilized to explore the tolerance levels of sensitive parameters. Design of experiment and regression analysis are applied in this method. The optimal tolerance levels are selected in accord with a quality-cost model to improve consistency of output response and reduce failure rates of critical components synchronously. The application in light-emitting diode (LED) drivers indicates details and potential. It shows that the proposed method provides a more effective way to improve performance and reliability of electronic circuits.     

幂律型流体雾化SPH方法数值分析

幂律型流体的雾化过程存在复杂的界面运动,用传统网格法很难精确追踪运动界面.为研究幂律型流体的雾化特性,运用SPH方法对典型的双股幂律型流体撞击雾化问题进行三维数值分析.根据文献实验,采用SPH方法模拟获得与实验条件相应的数值结果,对比后表明,二者雾化角相当吻合,数值结果还成功捕捉到液膜向液丝的破碎过程及网状的液丝分布状态,验证了方法的有效性.分析了射流速度和撞击角度对雾化角的影响,得到雾化角随着射流速度和撞击角度的增加而增大;对雾化后的速度场进行数值分析后表明,撞击点附近,惯性力的作用使速度场变化剧烈;在流体远离撞击点的过程中,粘性耗散作用使速度场趋于稳定,但速度大小小于初始撞击速度.     

基于航班排队仿真的终端区空域容量评估

为提升多扇区终端区空域容量评估的实效性,基于终端区交通流显著的排队特性,结合考虑扇区耦合关系,建立仿真模型并给出新的评估方法.以成都终端区为例,选取一周航班计划,针对每日运行状况共进行35次仿真,评定成都终端区平行双跑道隔离运行模式下的空域容量为47架次/h,并指出空域划设缺陷.经管制员雷达模拟机演练及实际运行数据验证,新评估方法有效,评估结论更符合实际.     

开放区域航路网战术协同控流策略研究

为降低航班运行延误、提高航路资源利用率,从空管部门和航空公司协同角度研究空中交通开放区域战术控流问题。引入协同决策理念和航路配流思想,考虑航路瓶颈点容流关系和航空器时间间隔标准,整合空中等待和改航等策略,研究建立了开放区域航路网络交通流模型,给出了协同控流策略及其执行程序。采用实际航班运行数据,对所提方法进行了仿真验证。结果表明,用于仿真验证的30架航班总延误时间降低了17.7%,不仅有效减少了航班延误、充分利用了航路资源,而且提高了航空公司参与决策的自主性与积极性,有利于区域航路交通流协同优化控制。     

装备项目质量进度成本一体化监督方法研究

从项目管理中的三角关系,装备质量进度成本一体化监督模型的可操作性和监督结果的可信性等方面,分析了武器装备质量进度成本一体化监督需求,研究了装备项目一体化监督函数具有的依概率收敛、边际效益递减律和极值等条件,利用卡诺质量模型,以统计均衡分析方法为手段,阐述了项目管理一体化监督函数的生成及求解过程.结合装备研制过程,采用定性分析与定量计算相结合的方式,在大质量观的主导下,以直-8型直升机典型故障为实例,阐明了项目一体化监督函数的求解过程,开展了项目监督风险决策和风险预警工作.     

基于CFD的变后掠翼单速度最优后掠角预测模型

为延长飞行器续航时间,探索变后掠翼飞行器控制规律,根据新型变后掠翼飞行器模型,探究了通过飞行器速度及迎角来控制弹翼后掠角度,以达到最优气动性能,从而使该飞行器获得更长续航力.选取飞行马赫数为0.4～0.8、前缘后掠角度为15°～45°内的39个关键点,在迎角为0°～14°范围内进行CFD仿真,将仿真结果在不同数学模型下...     

一类非线性系统的一阶D型迭代学习控制

传统的D型迭代学习控制的控制律设计方案依赖于被控系统的相对度.为解决该问题以及相对度增益与高阶微分运算的问题,针对一类具有任意高阶相对度的非线性系统,提出了基于虚拟模型的一阶D型迭代学习控制设计方法.该方法的主要思想是与具有任意高阶相对度的非线性被控系统并联一个一阶子系统,构造一个相对度为1、相对度增益可以任意设计的虚拟模型,在此基础上设计一个一阶D型迭代学习控制律,使得虚拟模型能够实现期望轨迹的完全跟踪,从而实际被控系统在一定误差范围内实现期望轨迹的跟踪.仿真实例验证了所提方法的可行性与有效性.