高超声速钝头体边界层转捩试验

为研究高超声钝头体边界层转捩以及头部钝度对转捩的影响,在FD-14和FD-14A两座激波风洞中开展了热流、压力扰动和高速纹影显示等综合测量。试验结果表明,转捩雷诺数关于钝度雷诺数的变化显示出转捩反转的趋势。压力扰动的功率谱密度（PSD）分析结果以流向离散分布云图形式显示,边界层高速纹影图像显示了第二模态波的发展、湍流的生成和熵层对边界层结构的显著影响。大头部钝度带来的强熵梯度熵层流动对边界层压力扰动频谱特性和流动结构影响显著,在转捩反转机理中起到重要作用。此外,马赫数对转捩的影响不容忽视。     

超声速膨胀角入射激波/湍流边界层干扰直接数值模拟

为了揭示膨胀效应对激波/湍流边界层干扰区内复杂流动现象的影响规律,采用直接数值模拟方法对来流马赫数2.9、30°激波角的入射激波与10°膨胀角湍流边界层相互作用问题进行了数值研究。系统地探讨了激波入射点分别位于膨胀角上游、膨胀角角点和膨胀角下游3种工况下膨胀角干扰区内若干基本流动现象,如分离泡、物面压力脉动及激波非定常运动、湍流边界层统计特性和相干结构动力学过程等。结果表明,激波入射点流向位置改变对分离区流向和法向尺度的影响显著,尤其是当激波入射点位于角点及其下游区域。研究发现,膨胀角干扰区内物面压力脉动强度急剧减小,分离区内压力波向下游传播速度将降低而在膨胀区内将升高,膨胀效应极大地抑制了分离激波的低频振荡运动。相较于入射激波与平板湍流边界层干扰,入射激波流向位置改变对膨胀角再附区速度剖面对数区及尾迹区影响显著,将导致其内层结构参数升高而外层降低,近壁区内将呈现远离一组元湍流状态的趋势。此外,流向速度脉动场本征正交分解分析指出,主模态空间结构集中在分离激波及剪切层根部附近而高阶模态以边界层内小尺度正负交替脉动结构为主。低阶重构流场结果表明,前者对应为分离泡低频膨胀/收缩过程而后者表征为分离泡高频脉动。     

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

舰载直升机理论风限图飞行模拟获取方法

获取舰载直升机实用风限图,仅依靠实装飞行试验或建模仿真都是非常困难的。通过起降飞行模拟试验获取理论风限图,结合少量的海上实装飞行验证试验是一种综合较优的方法。起降飞行模拟试验需要真实飞行员和高等级飞行模拟器参与,飞行模拟器中的母舰气流场数据、母舰运动可由建模仿真或试验测试得到,且必须考虑母舰气流场的非定场特性;只有当飞行员视景或视觉反馈受限时(如能见度降低时),飞行模拟器基座的六自由度运动才是必需的;用DIPES或Bedford方法量化飞行员主观操纵负担,结合记录的客观操纵数据,评判起降难度;典型的飞行模拟试验程序包含了不同风况下的进近和甲板着舰,通常每隔15°和5kn一个风况。通过起降飞行模拟试验得到的理论风限图,可以更加有效和安全地指导海上实装飞行验证试验,最终获得实用风限图。     

考虑可压缩与热传导的壁面函数边界条件及其应用

考虑到可压缩和热传导效应的壁面函数边界条件,被耦合到了采用k-ω两方程湍流模型、用有限体积法求解N-S方程的程序中。壁面函数基于耦合的速度和温度型,并且在边界层内的粘性子区和对数区内一致有效。引入壁面函数边界条件后,通过算例验证在y <100的范围内,得到的物面压力、摩阻、热流与实验结果比较,结果可靠。而无壁面函数边界条件时,要得到相同精度的结果,要求y ≈1。壁面函数的引入,为工程上准确预测飞行器在湍流流动中表面受力与气动热提供了保障。     

日照边缘区域电离层对耀斑的响应特点研究

利用MSIS模型和背景太阳辐射谱模型,在一定大耀斑辐射谱假设的前提下,计算了耀斑期间日照边缘区域的电子产生率,分析了这一区域电离层电子密度的变化特点.结果表明,大耀斑期间在日照边缘区域,甚至大于太阳天顶角90°的区域都有明显的电子产生率的增加.从不同太阳天顶角处的电子产生率剖面的形态来看,随着天顶角的增加最大电离率减少,但高度增加.计算还显示了在太阳天顶角小于90°的区域内电子产生率的垂直分布有明显的双峰结构,这种结构对应着电离层的E区和F区,但在天顶角大于90°区域,F区的电子产生率要大得多.考虑到离子和电子的复合过程,这一区域的总电子含量的增加主要产生在高F区.      

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.