模型预测控制在永磁同步电机系统中的应用发展综述

随着数字技术的发展,模型预测控制(MPC)已经广泛应用于交流传动系统。首先介绍了经典MPC策略——有限控制集MPC和连续控制集MPC的原理。其次综述了多步预测控制、多矢量预测控制、具有参数鲁棒性的预测控制、广义模型预测、显式模型预测这些常见的改进MPC的研究现状,并提出相关研究思路。最后,根据MPC的应用需求和研究现状,展望了未来需要进一步深入和拓展的研究方向。     

无刷双馈电机静止坐标系数学模型的研究

由于没有电刷和滑环,提高了运行的可靠性,降低了维护成本,因此无刷双馈电机(BDFM)在变速恒频发电领域有着广阔的应用前景。由于特殊的结构和工作原理,BDFM数学模型十分复杂。从BDFM多回路空间矢量数学模型出发,推导出了两个静止坐标系之间的坐标变换关系以及功率绕组静止坐标系数学模型和控制绕组静止坐标系数学模型,推导过程简洁明了。所得结果为BDFM理论分析和不同控制策略的研究提供了理论基础。MATLAB/Simulink环境下的仿真结果验证了数学模型及坐标变换关系的正确性。     

一种基于Deep-GBM的航空发动机中介轴承故障诊断方法

针对航空发动机中介轴承故障信号难于识别的特点,提出了一种深度梯度提升模型（Deep-GBM）对振动信号特征进行逐层学习以提高分类模型的准确率。开展某型航空发动机中介轴承故障模拟实验,并采用经验模式分解(EMD)方法对采集的振动信号进行分解,提取内蕴模式函数(IMF)分量非线性动力学参数样本熵作为原始故障特征。采用Deep-GBM对中介轴承内环故障、内环和滚动体综合故障、正常、滚棒剥落、滚棒划伤五种不同状态进行识别。实验结果表明,所提出的Deep-GBM故障诊断准确率达到87%,相对于传统的机器学习模型准确率最高提升了28%,并具有良好的泛化能力。      

带止口法兰连接结构刚度特性对结构振动影响

对带有止口的法兰连接结构刚度特性进行了数值仿真研究。使用有限元软件ANSYS分析了带有止口的法兰连接结构的迟滞特性。通过对止口接触面的变形-滑移机理分析,使用一个詹金斯单元和一个弹簧单元并联模拟法兰的一个扇区,并基于法兰弯曲变形时每个扇区的不同状态建立了整个法兰结构的弯曲刚度简化模型,并对该简化模型进行了仿真,该简化模型能够较准确地模拟带止口法兰连接结构的刚度特性。基于简化模型和梁单元建立了简化转子结构模型,分析了带有止口的法兰连接结构对转子稳态动力学响应的影响。结果表明带有止口的法兰连接结构的迟滞特性能够影响峰值频率,随着止口过盈量的增加,响应峰值显著降低,具有较好的振动抑制效果。      

移15°双十二相隐极同步整流发电机数学模型的研究

分别在abc坐标系和dq0坐标系下建立了移15°双十二相隐极同步整流发电机的基本数学方程,推导了电机电压、磁链、输出功率、电磁转矩和转子运动方程。在MATLAB/Simulink中建立了移15°双十二相隐极同步整流发电机的仿真模型。对两路输出进行了不平衡负载仿真和试验。仿真与试验结果相比基本一致,验证了移15°双十二相隐极同步整流发电机数学模型的正确性。这为双十二相同步整流发电机运行性能和励磁控制系统的研究奠定了基础。     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

C/SiC复合材料螺钉拉伸强度分布模型

C/SiC复合材料螺钉是在高超声速飞行器上应用越来越广泛的一类重要紧固件,但其拉伸性能存在较大散差,分布规律尚不明确,给材料选用和结构设计带来了很大困难。本文采用电子万能试验机对M8、M10、M12三种规格的平头C/SiC复合材料螺钉进行力学性能试验,并分析了拉伸强度的分布规律。在此基础上应用双参数Weibull模型对统计数据进行拟合,并对拟合结果进行了柯尔莫哥洛夫检验。结果表明:C/SiC复合材料螺钉的拉伸性能分布满足双参数Weibull模型,其特征强度β为212 MPa,形状参数α为9. 45,可以据此进行复合材料许用强度设计。     

钢板内部缺陷失效分析

采用120 mm厚的45#钢轧制板材经粗加工后进行调质处理,热处理后超声探伤发现钢板厚度方向中部存在缺陷。通过失效分析认为,钢板内部的缺陷为沿变形方向分布的带状组织,部分带状组织中存在沿晶裂纹。形成带状组织及裂纹的机理是原材料钢锭浇铸过程中心部形成枝晶偏析,轧制过程中偏析区被拉长因而形成偏析条带,条带区因富含Mn、S、P等元素形成硬度较高的马氏体组织,调质热处理过程中在组织应力及热应力作用下马氏体条带组织区域发生沿晶脆性开裂。     

湿热环境下复合材料层合板本构模型研究及其应用

近年来复合材料被广泛地应用于航空航天等工程领域。在实际的使用中,复合材料在不同的湿热环境下其力学性能会发生显著变化,针对这一问题,国内外已有大量的试验研究,而对湿热环境下复合材料的本构模型理论的研究则较少。在经典层合板理论基础上引入湿热膨胀系数的概念,通过定义一个无量纲的温度,建立材料弹性常数与湿热参数之间的函数关系,推导出复合材料单层板在湿热力耦合作用下的本构关系,同时加入三维Hashin失效判定准则对层合板的损伤演化及失效模式进行模拟。结果表明:该模型较好地预测了复合材料层合板在不同湿热环境下的弹性响应,为分析实际工程中复合材料结构模型在湿热环境下的力学行为提供了重要参考。