涡轮叶片内部微小V肋-凹陷涡复合冷却流动与传热数值模拟

为强化航空发动机涡轮叶片内冷通道传热性能,针对带有微小V肋-凹陷涡高效复合冷却结构矩形通道,采用Abe Kondoh Nagano （AKN） k-ε湍流模型数值模拟研究了肋高与凹陷深度组合对流动传热特性的影响机理。结果表明,当凹陷深度一定,复合结构的强化换热效果随肋高增加而增加,3mm肋高复合结构的传热相比纯凹陷提高了87.1%;当肋高一定,传热随凹陷深度增加先增强后基本保持不变,6mm深凹陷复合结构相比纯V肋提高了52.8%。通过在凹陷上游布置V肋,增强了越过V肋冲入凹陷内流体的湍动能,从而使凹陷前部回流区减小;同时来自微小V肋的涡流与凹陷内部的涡流相互作用,增强了整个流场的动量和热量输运,使通道换热均匀,并相较纯凹陷或纯V肋结构均有显著提升。     

1.5级涡轮前后轮缘密封封严流动特性研究

为了研究前后腔轮缘密封封严特性和封严出流与主流的交互作用,对转静叶片之间带有前后封严腔的1.5级涡轮进行了三维定常数值模拟,研究了不同封严流量下前后封严腔出口处流场分布并采用附加变量法对比分析了前后腔轮缘密封效率。结果表明：前封严腔主流燃气入侵位置主要受到来自上游导叶尾迹的影响,后封严腔主流燃气入侵位置主要受到下游导叶前缘位势场影响;封严出流影响了20%叶高以下的主流区域,增大了轮毂二次流强度;采用相同封严流量下时前封严腔的封严效率较后腔更低且有着更大的封严效率波动。     

Parametric study of turbine NGV blade lean and vortex design

The effects of blade lean and vortex design on the aerodynamics of a turbine entry nozzle guide vane (NGV) are considered using computational fluid dynamics. The aim of the work is to address some of the uncertainties which have arisen from previous studies where conflicting results have been reported for the effect on the NGV. The configuration was initially based on the energy efficient engine turbine which also served as the validation case for the computational method. A total of 17 NGV configurations were evaluated to study the effects of lean and vortex design on row efficiency and secondary kinetic energy. The distribution of mass flow ratio is introduced as an additional factor in the assessment of blade lean effects. The results show that in the turbine entry NGV, the secondary flow strength is not a dominant factor that determines NGV losses and therefore the changes of loading distribution due to blade lean and the associated loss mecha-nisms should be regarded as a key factor. Radial mass flow redistribution under different NGV lean and twist is demonstrated as an addition key factor influencing row efficiency.     

透平叶片变切削加工工艺数据库设计与开发

透平叶片是透平机械的核心零件之一,因其复杂的曲面造型和低刚度性,被认为是机械加工中的难题.通过Visual Basic编程语言进行叶片切削工艺数据库开发,在功能上实现面向叶片工艺变切削参数智能推荐、相似工艺实例推理和数控加工工序卡片、程序清单的输出,方便企业用户使用,提高工作效率和准确性..     

Numerical analysis for impacts of nozzle end-clearances on aerodynamic performance and forced response in a VNT turbine

It has been well known that nozzle end-clearances in a Variable Nozzle Turbine (VNT) are unfavorable for aerodynamic performance, especially at small openings, and efforts to further decrease size of the clearances are very hard due to thermal expansion. In this paper, both the different sizes of nozzle end-clearances and the various ratios of their distribution at the hub and shroud sides were modelled and investigated by performing 3D Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA) simulations with a code of transferring the aerodynamic pressure from the CFD results to the FEA calculations. It was found that increasing the size of the nozzle end-clearances divided equally at the hub and shroud sides deteriorates turbine efficiency and turbine wheel reliability, yet increases turbine flow capacity. And, when the total nozzle end-clearances remain the same, varying nozzle end-clearances’ distribution at the hub and shroud sides not only shifts operation point of a VNT turbine, but also affects the turbine wheel vibration stress. Compared with nozzle hub clearance, the shroud clearance is more sensitive to both aerodynamic performance and reliability of a VNT turbine. Consequently, a possibility is put forward to improve VNT turbine efficiency meanwhile decrease vibration stress by optimizing nozzle end-clearances’ distribution.     

Effect of inlet rotating swirl on endwall film cooling for two representative hole arrangements

The swirl generator is widely used in lean-burn combustor to guarantee flame stability and reduce NO_x emissions. Thus, the non-uniformities induced by the swirler would affect and damage film-cooling effectiveness on the turbine components, even blow-off coolant coverage, to some certain extent. The arrangement of film-cooling holes was normally designed to be perpendicular to the axial direction and in standard straight row. In this work we experimentally studied the effects of inlet swirl and mass flow ratio on traditional film cooling holes arrangement and a new arrangement pattern whose holes are located along the isobars. Results indicated that the swirl perturbation would damage film coverage. The film-cooling effect of endwall on which the holes are along the isobars, is invariably more promising than that of endwall on which hole arrangement is perpendicular to axial with the same mass flow of coolant, whether the inlet conditions is uniform or not.     

转子-SFDB系统通过共振时的瞬态动力特性

 本文对一个支于挤压油膜阻尼器轴承的柔性转子升降速通过共振时发生跳跃现象的瞬态过程进行了试验研究和理论分析,探讨了油膜压力边界状态,不平衡参数、转速范围与跳跃现象之间的相互关系,所得结论对于挤压油膜阻尼器的工程设计具有实际意义。     

涡轮的重复进气道的试验研究

用小型涡轮取代蓄电池和高压气瓶作为导弹上的辅助能源是明显地发展趋势.重复进气涡轮能较好地适应这种辅助能源系统的要求.本文研究了涡轮的不同形状的重复进气道,及其与喷嘴的匹配,不同的喷嘴出口角、流速等因素对损失的影响,给出了在所研究的条件下最佳形状的重复进气道、喷嘴和重复进气道的最佳匹配.     

冲击粗糙肋壁面换热准则关系式的建立

模拟高性能航空发动机涡轮叶片弦中区冷却结构，建立冲击粗糙复合冷却实验模型，通过对大量实验数据的分析和整理，建立了换热准则关系式。与实验结果对比表明：该准则关系式与实验实测数据吻合较好，精度较高，对于冲击粗糙肋壁面复合冷却技术的研究和工程结构设计都具有一定的指导价值。     

涡轮叶片疲劳寿命公式及可靠性预测方法

本文推导了液体火箭发动机涡轮叶片疲劳寿命公式,并用概率统计、断裂力学方法,分析了可靠性预测方法.