利用TDS研究二次硬化钢中氢的扩散行为

利用升温脱氢分析装置(TDS)和慢速拉伸试验方法(SSRT)研究了一种二次硬化钢中氢的扩散行为及其对塑性的影响。结果表明,由于二次硬化实验钢中存在大量细小碳化物,氢的扩散系数约为3.42×10-8cm2.s-1,明显低于通常淬火回火马氏体钢。TDS分析发现,实验钢中存在两个氢逸出峰,激活能分别为20.2kJ.mol-1和24.6kJ.mol-1,由晶界、位错等弱氢陷阱引起。拉伸试样的断面收缩率随氢质量分数的增加先线性下降,氢质量分数每增加1×10-4%断面收缩率下降约12%;当氢质量分数达到5×10-4%时,断面收缩率低于10%,断口呈沿晶状。     

腈纶/芳纶共混短纤维用量对柔性绝热层材料性能的影响

比较了腈纶短纤维增强EPDM／NBR共混橡胶（EN体系）、芳纶短纤维增强EPDM／NBR共混橡胶（EA体系）、腈纶／芳纶混杂短纤维增强EPDM／NBR共混橡胶（ENA体系）等3种体系中,短纤维用量对材料不同方向上力学性能的影响;EA和ENA两种不同体系中,短纤维用量对材料烧蚀性能和相对密度的影响。在短纤维用量为6份时,ENA体系的拉伸强度和伸长率比EA体系大,烧蚀性能比EA体系好,相对密度也比EA体系低。     

白炭黑与硼酚醛树脂用量对EPDM/NBR柔性绝热层材料性能的影响

通过比较分析白炭黑与硼酚醛树脂用量对EPDM/NBR柔性绝热层材料拉伸强度、断裂伸长率、质量烧蚀速率和线烧蚀速率以及相对密度的影响,得出随着白炭黑或硼酚醛树脂用量的增加,柔性绝热层材料的拉伸强度和相对密度呈递增趋势,烧蚀速率呈递减趋势,断裂伸长率在白炭黑和FB用量各自为20份时有极大值.     

固液混合火箭发动机固体燃料的燃速计算

分析了固液混合火箭发动机的燃烧特点、燃烧中气相过程和固体燃料内部的传热过程,利用由传热理论得出的固体燃料燃速公式和阿累尼乌斯(Arrhenius)燃速公式耦合计算,得到了燃速与氧化剂流率、轴向距离、装药初温和时间的变化规律.计算结果表明固体燃料燃速主要受氧化剂流率和轴向距离的影响,随氧化剂流率的增加而增加,随轴向距离的增加而减小.固体燃料燃速温度敏感性小,在设计发动机时可以不考虑装药初温的影响.利用热力计算得到了绝热燃烧温度与氧化剂流率和药柱长度的变化规律,绝热燃烧温度随氧化剂流率的增加存在一最大值.计算结果与相关文献的报道比较吻合,为进一步研究固液混合火箭发动机的燃烧及流动问题打好了基础.     

航材消耗的时间序列分析

本文采用时间序列分析法对某种航材故障率进行预测,用移动平均法消除时间序列的长期趋势和周期变动,然后按月平均法求出季节指数,并对季节指数进行调整,然后根据拟合的趋势方程对此种航材的故障率进行预测.其结果能为航材的可靠性保障提供理论依据.     

SCC investigation of low alloy ultra-high strength steel 30CrMnSiNi2A in 3.5wt%NaCl solution by slow strain rate technique

To evaluate stress corrosion cracking(SCC) mechanism of low alloy ultra-high strength steel 30CrMnSiNi2 A in environment containing NaCl, SCC behavior of the steel in 3.5wt% NaCl solution is investigated by slow strain rate technique(SSRT) with various strain rates and applied potentials, surface analysis technique, and electrochemical measurements. SCC susceptibility of the steel increases rapidly with strain rate decreasing from 1 · 10 5s 1to 5 · 10 7s 1, and becomes stable when strain rate is lower than 5 · 10 7s 1. SCC propagation of the steel in the solution at open circuit potential(OCP) needs sufficient hydrogen which is supplied at a certain strain rate.Fracture surface at OCP has similar characteristics with that at cathodic polarization 1000 mVSCE, which presents characteristic fractography of hydrogen induced cracking(HIC).All of these indicate that SCC behavior of the steel in the solution at OCP is mainly controlled by HIC rather than anodic dissolution(AD).     

Characteristics of the soil-like substrates produced with a novel technique combining aerobic fermentation and earthworm treatment

The soil-like substrate (SLS) technique is key for improving the closure of bioregenerative life support system (BLSS) by recycling the inedible biomass of higher plants. In this study, a novel SLS technique (NSLST) was proposed: aerobic fermentations at 35 °C for 1 day, then 60 °C for 6 days, finally 30 °C for 3 days, followed by earthworm treatment for 70 days. Comparing with the original SLS technique (OSLST), its process cycle was 13 days shorter, and the dry weight loss rate (81.1%) was improved by 24.77%. The cellulose and lignin degradation rates were 96.6% and 94.6%. The concentrations of available N, P and K in mature SLS were respectively 776.1 mg/L, 348.0 mg/L and 7943.0 mg/L. Low CH₄ and NH₃ production was observed, but no accumulation. According to the seed germination test, the SLSs were feasible for plant growth. This investigation will provide a preliminary foundation for BLSS design.     

某型直升机液压减摆器渗油故障的排除

介绍了某型直升机液压减摆器的结构特点和密封原理,用故障树的方法梳理了影响液压减摆器渗油的原因,针对一特定案例进行了渗油原因分析,并制定了相应的改进措施。     

Drilling load modeling and validation based on the filling rate of auger flute in planetary sampling

Some type of penetration into a subsurface is required in planetary sampling. Drilling and coring, due to its efficient penetrating and cuttings removal characteristics, has been widely applied in previous sampling missions. Given the complicated mechanical properties of a planetary regolith, suitable drilling parameters should be matched with different drilling formations properly. Otherwise, drilling faults caused by overloads could easily happen. Hence, it is necessary to estab-lish a drilling load model, which is able to reveal the relationships among drilling loads, an auger's structural parameters, soil's mechanical properties, and relevant drilling parameters. A concept for the filling rate of auger flute (FRAF) is proposed to describe drilling conditions. If the FRAF index under one group of drilling parameters is less than 1, this means that the auger flute currently removes cuttings smoothly. Otherwise, the auger will be choked with compressed cuttings. In dril-ling operations, the drilling loads on the auger mainly come from the conveyance action, while the drilling loads on the drill bit primarily come from the cutting action. Experiments in one typical lunar regolith simulant indicate that the estimated drilling loads based on the FRAF coincide with the test results quite well. Based on this drilling load model, drilling parameters have been opti-mized.     

建设中国民航的数据交换平台

数据交换平台是民航公共信息网络平台的核心系统。提出了基于XML标准和Web Service技术的民航数据交换平台系统设计思想，提出了系统的建设思路和总体目标、设计原则和技术措施。描述了数据交换平台的数据交换流程和系统体系结构。