一种温度动态调节方法及其动态性能仿真研究

航空气源模拟试验台主要用于模拟不同飞行状态时发动机给空气管理系统的供气,由于飞机爬升、降落时发动机供气参数会急剧变化,因此航空气源模拟试验台需具备动态能力.基于一种温度动态调节方法,在合理简化的基础之上采用NHT方法对其温度动态性能进行了仿真研究,仿真结果表明该温度动态调节方法能够满足温度动态性能需求,对动态航空气源模拟试验台的设计选型有较高的参考价值.     

Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

蒙皮零件拉伸粗晶的控制研究

针对民机2014材料(材料规范L164/L165/L167)、某型机2B06OB材料拉伸成形过程中出现的粗晶缺陷,进行了大量的工艺试验,分析并查找出粗晶产生的原因,摸清材料性能,并提出最终解决方案。     

新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性试验研究

随着新型Al-Li-Cu-Mg合金蒙皮在航空航天等高技术工业的应用日益广泛,新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性已成为新型Al-Li-Cu-Mg合金板蒙皮成形质量精确控制以及蒙皮设计迫切需要解决的关键问题.因此,首先获得了新型T8态Al-Li-Cu-Mg合金的最佳热处理工艺参数;其次,采用试验方法,研究了不同热处理状态的拉伸成形过程,揭示了新型Al-Li-Cu-Mg合金板材的拉伸成形特性.发现通过固溶处理,后续时效能够显著提高新型T8态Al-Li-Cu-Mg合金材的拉形能力;在新型A1-Li-Cu-Mg合金板材拉形过程,桔皮现象主要出现在补拉阶段,蒙皮悬空区应变值＞0.0215时,板材表面将出现桔皮,且与材料热处理状态无关.     

基于支持向量机和粒子群算法的钛合金铣削加工参数优化

钛合金材料在加工过程中受铣削力影响易于产生变形而影响加工效果,为保证加工质量,提高生产效率及降低加工成本,研究切削加工参数的合理选择非常重要.对钛合金材料Ti6Al4V铣削加工进行有限元数值计算,结合试验设计方法构建了基于支持向量机的切削力预测模型,以材料去除率为优化目标,提出了一种基于支持向量机和粒子群算法的优化方法,对钛合金铣削加工参数进行了优化.结果表明,该方法准确、高效、可行,为钛合金加工工艺参数优化提供一种新的方法,具有良好的推广价值.     

TC4钛合金静止轴肩和传统搅拌摩擦焊的温度场对比

基于有限元软件ABAQUS对6mm厚的TC4钛合金传统及静止轴肩搅拌摩擦焊温度场进行了有限元模拟.结果表明,对比传统搅拌摩擦焊接,静止轴肩搅拌摩擦焊接具有较小的高温区,前进方向上具有较大的温度梯度,厚度方向上呈现柱状椭球形分布,上、下表面温度峰值差异较小,具有重叠性较好的热循环曲线.     

液化天然气作为航空燃料的发展趋势及特点分析

为研究液化天然气(LNG)作为航空燃料的可行性,对LNG的特点、发展趋势及作为航空燃料存在的问题进行了分析.采用了横向比较的方法,将LNG与新的航空替代燃料和传统航空燃料进行了比较和计算分析.结果表明:与新的航空替代燃料相比,LNG具有来源广泛、经济性好、发动机适应性强等优点.与传统航空燃料相比,LNG的储量大,可使用100年以上;可燃极限宽、污染物排放低,NOx排放仅为航空煤油的1/4;单位质量能量密度高、成本低,其燃料成本仅为航空汽油的一半,航空煤油的1/3;同时还具有可用于发动机高温部件冷却用的冷能,是一种极富潜力的航空燃料.指出在LNG作为航空燃料方面急需开展动力系统与飞机结构的匹配、燃料相态的有效转化及不同燃料在燃烧室内的反应特性等方面的研究工作.      

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。