全文获取类型
收费全文 | 3023篇 |
免费 | 894篇 |
国内免费 | 583篇 |
专业分类
航空 | 3017篇 |
航天技术 | 534篇 |
综合类 | 285篇 |
航天 | 664篇 |
出版年
2024年 | 16篇 |
2023年 | 77篇 |
2022年 | 148篇 |
2021年 | 192篇 |
2020年 | 164篇 |
2019年 | 148篇 |
2018年 | 138篇 |
2017年 | 208篇 |
2016年 | 227篇 |
2015年 | 175篇 |
2014年 | 201篇 |
2013年 | 155篇 |
2012年 | 235篇 |
2011年 | 280篇 |
2010年 | 155篇 |
2009年 | 220篇 |
2008年 | 169篇 |
2007年 | 198篇 |
2006年 | 207篇 |
2005年 | 121篇 |
2004年 | 113篇 |
2003年 | 122篇 |
2002年 | 90篇 |
2001年 | 86篇 |
2000年 | 81篇 |
1999年 | 76篇 |
1998年 | 106篇 |
1997年 | 76篇 |
1996年 | 56篇 |
1995年 | 54篇 |
1994年 | 54篇 |
1993年 | 39篇 |
1992年 | 23篇 |
1991年 | 32篇 |
1990年 | 23篇 |
1989年 | 17篇 |
1988年 | 11篇 |
1987年 | 5篇 |
1986年 | 1篇 |
1984年 | 1篇 |
排序方式: 共有4500条查询结果,搜索用时 908 毫秒
651.
针对传统航空发动机响应速度慢,难以在紧急事件中用于控制受损飞机完成起降过程的问题,采用高速慢车控制模式来提升发动机加速性能,通过增加发动机在慢车时高压压气机转速,为加速前期提供更大的燃油流量,从而缩短发动机从慢车至最大状态的加速时间。为保证慢车时高压转子转速提高的同时发动机推力和稳定裕度不变,通过修改高压压气机可调导叶控制计划来调整高压转子工作点。仿真结果显示,与原有控制相比,采用高速慢车快速响应控制模式的发动机加速上升时间从原来的2.00s缩短至1.86s,而高压压气机最小喘振裕度仅由16.01%下降至14.81%,同时慢车推力基本保持不变。 相似文献
652.
通过常规力学性能、扫描电镜、透射电镜等测试分析方法研究了T8I6二次时效制度对Mg、Ag和Zn复合微合金化的Al-3.48Cu-1.44Li合金微观组织和力学性能的影响.结果表明,与单级时效相比,二次时效合金强度提高,而塑性略降;合金强度随第三级时效时间的延长进一步提高.最优的合金其抗拉强度(UTS)、屈服强度(YS)和延伸率分别为613.7、564.9 MPa和6.8%.合金的强化相主要为T1相,另有少量的θ'相和S'相.二次时效促进强化相,特别是T1相的二次沉淀,提高合金的强度,同时几乎不损失塑性. 相似文献
653.
短距起飞/垂直降落(STOVL)飞机由于其优越的作战性能,受到了世界航空大国的高度重视。通过借鉴目前最先进的 STOVL 动力 F135- PW -600发动机技术发展思路,研究了基于国内某型发动机改 STOVL 动力方案时,主发动机与升力风扇之间的匹配和约束关系。研究结果表明:随着升力风扇压比和流量的增加,主发动机升力减小,升力风扇升力增加;同一主发动机状态下,升力风扇流量越大,发动机前后升力平衡的升力风扇压比越小,总升力越大;主发动机性能越高,发动机前后升力平衡的升力风扇压比和流量越大,发动机总升力也越大。 相似文献
654.
655.
656.
657.
Single track and single layer formation in selective laser melting of niobium solid solution alloy 总被引:1,自引:2,他引:1
Selective laser melting (SLM) was employed to fabricate Nb-37Ti-13Cr-2Al-1Si (at%) alloy, using pre-alloyed powders prepared by plasma rotating electrode processing (PREP). A series of single tracks and single layers under different processing parameters was manufactured to evaluate the processing feasibility by SLM, including laser power, scanning speed, and hatch distance. Results showed that continuous single tracks could be fabricated using proper laser powers and scanning velocities. Both the width of a single track and its penetration depth into a substrate increased with an increase of the linear laser beam energy density (LED), i.e., an increase of the laser power and a decrease of the scanning speed. Nb, Ti, Si, Cr, and Al elements distributed heterogeneously over the melt pool in the form of swirl-like patterns. An excess of the hatch distance was not able to interconnect neighboring tracks. Under improper processing parameters, a balling phenomenon occurred, but could be eliminated with an increased LED. This work testified the SLM-processing feasibility of Nb-based alloy and promoted the application of SLM to the manufacture of niobium-based alloys. 相似文献
658.
温度对液体中超声速度的影响 总被引:4,自引:0,他引:4
本文导出了超声波速度同液体压缩系数及密度关系,研究了压缩系数及密度与温度的关系,进而研究了温度对声速及声时的影响,用实验测量了不同的液体成份下的声时同温度的关系,从而提出了进行液体成份分析所必需的参量,对用超声波分析液体成份提供了理论依据,对提高产品质量及实现工业在线检测有一定的实用价值。 相似文献
659.
660.