电火工品在线检测装置的温度特性

介绍了工程使用中电火工品的检测电路原理图和工作原理,并在高低温状态下对电路进行了性能研究.为满足电路在较大温度范围内的性能指标,根据高低温状态下的实测值调整了电路的门限值,满足了较大温度范围内电火工品的检测.     

低压断路器灭弧室温度检测

设计了基于光纤光栅传感系统的低压断路器灭弧室温度检测装置,实验测量出灭弧室温度数据,进行了数据的有限元分析,绘制出灭弧室内温度场分布图.     

带集中热源的散热器温度场的数值分析

随着大规模集成电路的发展,电子设备的封装体积越来越小,功率却越来越大,这就使电子设备的温度日益增高,而电子设备的可靠性又与温度密切相关,良好的散热是电子设备应用中重要的一环.本文以通用的矩形翅片式散热器来对比带集中热源和带平均热源的散热器的温度差异,提出以嵌入热管的方法来解决带集中热源散热器的散热难题,并运用IcEPEK软件对其可行性进行了验证.     

胶粘剂弹性模量对间隙接头应力和强度的影响

 运用弹塑性有限元法,研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头的影响。通过分析胶层和被粘物的应力分布,结果表明：间隙连接对接头端部的应力分布无明显影响,但对间隙附近的应力峰值影响较大;随着胶粘剂弹性模量的增大,间隙附近的应力峰值反而减小;对于高弹性模量胶粘剂接头,间隙对接头的应力峰值无明显影响,在不降低接头名义强度的基础上极大地提高了接头的实际强度;而对于低弹性模量胶粘剂接头,间隙使得接头的应力峰值明显上升,显著地降低了接头的名义强度和实际强度。数值模拟结果与已发表的试验数据大致吻合。     

陶瓷纤维梯度增强活塞的梯度方程研究

 功能梯度材料零件具有单质材料零件无法比拟的理化性能优势,然而由于材料分布复杂以及对功能梯度材料本身性能研究不充分,使性能分析存在很多困难。论文应用复合材料热性能理论,采用有限元分析软件ADINA,分析陶瓷纤维梯度增强活塞（材料梯度方程的参数不同）的温度分布和应力分布,结果表明陶瓷纤维梯度层可以明显改变活塞温度分布,缓和由于热膨胀系数不匹配,在陶瓷纤维增强层与活塞本体交界处产生的应力。根据计算结果拟合出温度峰值、整体应力峰值和层间应力峰值与方程系数之间的曲线,并加以验证。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

冲击载荷作用下新型阻尼铝合金的阻尼及力学性能

 采用冲击实验装置研究了新型阻尼铝合金材料在冲击载荷作用下的动态力学性能及表征方法。研究结果表明：采用冲击实验的冲击功及能量参数能够科学合理地表征铝合金材料的力学及阻尼性能。新型阻尼铝合金材料的抗冲击载荷能力和阻尼性能均高于普通铸造铝合金材料86%及37%左右,且内部组织致密、均匀细小,具有优良的综合性能。     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

Advances and challenges on springback control for creep age forming of aluminum alloy

Creep age forming(CAF) is an advanced forming technology that combines creep deformation and age hardening processes. When compared with the conventional forming technologies including roll bending and shot-peen forming, CAF has many advantages of low residual stress,excellent dimensional stability, good service performance and short production cycle. It is an optimal technique for precise manufacturing for shape and properties of large-scale complicated thinwalled components of light-weight and...     

Revisiting the space-time gradient method: A time-clocking perspective,high order difference time discretization and comparison with the harmonic balance method

This paper revisits the Space-Time Gradient(STG) method which was developed for efficient analysis of unsteady flows due to rotor–stator interaction and presents the method from an alternative time-clocking perspective. The STG method requires reordering of blade passages according to their relative clocking positions with respect to blades of an adjacent blade row. As the space-clocking is linked to an equivalent time-clocking, the passage reordering can be performed according to the alternativ...