Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

R141b在圆形微通道内的沸腾换热实验研究

为提高换热强度、解决设备内部高热流密度散热问题,采用实验方法研究R141b在不同直径(D=0.5mm和1.0mm)水平圆形微通道内的沸腾换热特性,分析了热流密度(q=2.0kW/m~2～47.6kW/m~2)、质量干度(x=0～0.6)、质量流速(G=111.11kg/(m~2·s)～333.33kg/(m~2·s))的变化对平均传热系数h的影响,探究不同情况下影响沸腾换热的主导因素。实验研究表明:平均传热系数h随热流密度q的增加而减小,在不同范围内减小速率有明显差异;热流密度q=2kW/m~2～5kW/m~2时质量流速G对平均传热系数h影响较明显,热流密度较高时质量流速G对换热影响很小;在质量流速G=111.11kg/(m~2·s)～333.33kg/(m~2·s),质量干度x0.3时,平均传热系数h随质量干度x增加而明显下降,在设计微通道换热器时应尽量使R141b处于初始沸腾阶段以获得更好换热效果,并采取一定措施预防干度过高引起的换热恶化。     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

聚酰亚胺胶粘剂的粘接性能

 采用等摩尔的酮酐（BTDA）和醚胺（ODA）在N,N 二甲基甲酰胺(DMF)中合成了线形缩聚型聚酰胺酸(PAA),并用红外光谱对其结构进行了表征,用TGA对其热关环亚胺化后进行了分析,结果表明其热分解温度可达600 ℃,所成薄膜具有良好的韧性。同时采用纳迪克酸酐（NA）为封端剂,通过调整NA/BTDA/ODA的比例,合成了不同分子量的PAA预聚体,并用红外光谱对其结构进行了表征,对其热关环亚胺化后进行差热分析,表明其端基交联固化温度为350 ℃左右,且随着分子量的提高峰温向高温方向移动。TGA表明,热固性聚酰亚胺（PI）交联固化后的热分解温度为483 ℃左右。采用上述线形缩聚型PAA与热固性PI共混,将固化后线形缩聚型PI的韧性与热固性PI高温性能结合起来,直接用做耐高温胶粘剂,可以获得较高的室温和高温剪切强度,并具有良好的高温热老化性能。     

Investigation of the role of aziridine bonding agents on the aging of the composite solid rocket propellant(CSRP)

The role of bonding agents on the aging characteristics is one of the important research topics.Aging program of the prepared propellant samples was conducting as follows:Five samples,two free of bonding agents,and three containing an aziridine based bonding agents(MAPO,HX-752,MAT4),four samples based on different bonding and curing agents all were aged at 70 ℃.The prepared bonding agent "MAT4" gave remarkable improvements and resulted in highly stable mechanical properties comparing with HX-752 or MAPO.The selected bonding agents family inhibited the rate of decomposition of the propellants during the aging periods and supported the propellant matrix against decomposition at the elevated temperatures.      

焊后时效处理对2219铝合金VPTIG接头微区组织和显微硬度的影响

研究了不同温度焊后时效处理对2219铝合金变极性钨极氩弧焊(VPTIG)接头各微区显微组织的影响,采用显微硬度测试和透射电镜观察分析焊接接头各微区析出相的形貌和分布。结果表明,焊后时效处理温度不同,焊接接头各微区显微组织和硬度发生的变化不同。热影响区中的完全回复区对焊后时效最为敏感,低温处理时显微硬度就有明显增长,并在160℃处理时达到最大涨幅;焊缝区变化相对较小,其显微硬度的最高涨幅出现在210℃,且小于前者;热影响区中的过时效区最为稳定,显微硬度的最大增长同样出现在160℃,但涨幅很小。透射电镜观察表明,焊接接头各微区的显微硬度变化主要与时效强化相的析出行为有关。     

热处理对激光增材制造Ti2AlNb基合金组织及性能的影响

利用激光增材制造技术制备出Ti-22Al-25Nb合金薄壁试样,分析了沉积态和热处理态试样的宏观形貌、相组成和显微组织,以及不同制度热处理态试样的组织和室温拉伸性能.结果表明,沉积态试样相组成沿沉积高度方向呈现由B2+O+α2→B2+O→B2的变化趋势;热处理态试样的微观组织和相组成均匀,由B2、O、α23相组成;经930℃保温2h空冷的固溶处理和800℃保温24h空冷的时效处理后,合金室温拉伸性能好,抗拉强度为1017MPa,断后伸长率为6.0％.     

基于单片机和CdS涂层老化探头的装备腐蚀监测系统设计

针对装备对腐蚀状态监测需求,以 MSP320单片机为核心控制器、CdS涂层老化探头为腐蚀状态传感器,设计了一款 4路腐蚀状态监测系统,并用于某型车辆腐蚀状态监测。实验结果表明,该系统能真实监控该型车辆的腐蚀状态,为该车辆的预防性维修提供了重要技术和数据支持。同时,该系统具有安装灵活方便、工作可靠、体积小等优点,具有较高的推广应用价值。