正态-复合非时齐Poisson过程模型结构可靠性当量正态设计

讨论强度R～N（μ_R，_R），应力｛S（t），t∈［0，T］｝为非时齐Poisson过程模型结构可靠性当量正态设计。获得应力在设计基准期［0，T］内的最大值概率分布及统计参数估计；正态－复合非时齐Poisson过程模型结构可靠度及结构可靠性当量正态设计表达式。     

P1─—多面体的对偶图形的性质

本文研究了P1─—多面体与其对偶图形的对偶图形边长之间的关系问题．设P1─—多面体的边长为a，其对偶图形的对偶图形的边长为C，则其中θ1为多面体A的过顶点的相邻两校之间的夹角，θ2为多面体B的过顶点的相邻两校之间的夹角，取θ＝max｛θ1，θ1｝     

Computational engineering analysis of external geometrical modifications on MQ-1 unmanned combat aerial vehicle

This paper focuses on the effects of external geometrical modifications on the aerodynamic characteristics of the MQ-1 predator Unmanned Combat Aerial Vehicle (UCAV) using computational fluid dynamics. The investigations are performed for 16 flight conditions at an altitude of 7.6 km and at a constant speed of 56.32 m/s. Two models are analysed, namely the baseline model and the model with external geometrical modifications installed on it. Both the models are investigated for various angles of attack from −4° to 16°, angles of bank from 0° to 6° and angles of yaw from 0° to 4°. Due to the unavailability of any experimental (wind tunnel or flight test) data for this UCAV in the literature, a thorough verification of calculations process is presented to demonstrate confidence level in the numerical simulations. The analysis quantifies the loss of lift and increase in drag for the modified version of the MQ-1 predator UCAV along with the identification of stall conditions. Local improvement (in drag) of up to 96% has been obtained by relocating external modifications, whereas global drag force reduction of roughly 0.5% is observed. The effects of external geometrical modifications on the control surfaces indicate the blanking phenomenon and reduction in forces on the control surfaces that can reduce the aerodynamic performance of the UCAV.     

螺旋桨桨叶1P气动载荷研究

介绍了一种１Ｐ载荷实验研究方法－桨叶应变测试法,首先通过桨叶剖面速度三角形及气动力分析给出了１Ｐ载荷与测量应变的关系,然后通过地面试验和飞行试验进行了验证。试验结果表明,螺旋桨１Ｐ载荷主要由于非对称气流流过桨盘面改变了桨叶剖面速度三角形而引起,迎角,侧滑角的增加,会产生较大的１Ｐ载荷;机动飞行,如快速拉杆,荷兰滚等也会产生较大的１Ｐ载荷。     

猎鹰9号火箭发射及箭体复用的分析

猎鹰9号火箭截至2023年年底已完成286次发射。对猎鹰9号火箭特别是Block5版本火箭的发射情况进行了完整梳理统计,重点分析了一级箭体的复用情况以及发射、回收的相关能力保障,对火箭的经济性和未来前景作了预测。     

7075Al/SiCp复合材料热压缩变形的研究

采用圆柱试样在Gleeble-1500热模拟机上对7075Al／SiCp复合材料进行高温压缩变形实验，变形温度为300-500℃，应变速率为0．001-1s^-1。结果表明：7075Al／SiCp复合材料的流变应力大小受变形温度和应变速率的强烈影响，流变应力随应变的增加而逐渐增加，出现一峰值后逐渐下降；流变应力随变形温度的升高，应变速率的降低而降低。可用Zener—Hollomon参数的双曲正弦形式来描述7075Al／SiCp复合材料高温压缩变形流变应力，其变形激活能Q为279．659KJ/mol。     

一种基于频移补偿的apFFT相位估计改进方法及应用

全相位快速傅里叶变换（all phase Fast Fourier Transform,apFFT)相位一致性特点使正弦信号相位估计不受频率估计影响,但由于频谱泄露和栅栏效应,apFFT相位估计性能受信号频率位置影响。针对该问题,提出了一种基于高精度频率估计和补偿的apFFT相位估计方法。首先,对信号进行高精度频率估计,并以此对信号进行频移补偿,然后对补偿信号进行apFFT,最后求解信号相位。蒙特卡洛仿真结果表明：所提算法的相位估计性能不受信号频率位置影响,相位估计误差性能与理论值一致,受两参数克拉美罗界（CRLB₂）约束,约为1.158 2倍的CRLB₂;相位估计性能和抗噪声能力明显优于经典apFFT算法和其他对比算法。更进一步,利用我国首次火星探测器TW-1（天问一号）近火捕获段干涉测量数据进行算法验证,结果表明：相位估计精度约4 mrad,干涉测量时延估计精度约50 ps。     

浮空器管材结构连接方式比较及拉伸强度分析

浮空器结构件如吊舱、过渡架及推进支架等多采用金属管材连接。目前,浮空器管材结构连接缺乏使用工况下极限值实测数据,材料及连接方式选择的理论支撑尚有不足。据此,对常用管材的不同连接方式进行比较及断裂分析。研究中铝合金和钛合金管材分别采用螺接及焊接的方式进行连接,测试样品的力学性能并结合仿真分析验证其断裂原因。结果表明:TA1钛合金管材采用焊接连接方式,相对螺接方式连接强度提高 87.9%;6061铝合金管材采用螺接连接方式,相对焊接方式连接强度提高 39.3%。2A12铝合金管材焊接连接强度优于螺接连接强度。同时,分析断裂原因发现,管材形变是影响焊缝连接强度的重要因素;应力集中易发生在管材端部连接处,导致端部焊缝发生断裂;管材形变会使母材断裂时伴有撕裂现象,进一步降低管材的最大连接强度。     

Observations of non-migrating tides and ionospheric perturbations of O(D) airglow by ISUAL instrument

In this paper, we present the spatial variations of O(¹D) airglow observed by the ISUAL (Imager of Sprites and Upper Atmospheric Lightning) instrument on board the FORMOSAT-2 satellite. With a CCD camera and a 630 nm filter, ISUAL can measure global atmospheric emissions lying between the heights of 80 and 300 km. In days of 3–6 September 2008 and 25–27 February 2009, ISUAL has measured the emissions of O(¹D) airglow with results showing strong longitudinal peak-3 and peak-4 structures. The Lomb-Scargle analyses for these two cases show periods of longitudes of 120° and 90° supporting the DE2 and DE3 non-migrating tides. The 630 nm emissions are enhanced in equatorial regions and are lying along the equator. Over Africa its intensity can sometimes increase up to 80% relative to other longitudes. The perturbation is so strong that non-migrating tides are erased. A case of bimodal distribution with strong emissions at latitudes in equator and mid-latitude in geographic coordinates was observed.     

深空探测器被动式高精度多普勒测量方法与应用

针对深空探测器的单程多普勒测量需求,研究了被动式高精度多普勒测量方法及其实现技术。该方法基于探测器测控信标残留载波等点频信号和VLBI测站高精度氢原子钟频标,构造出与实际接收信号频率接近的参考信号;再通过本地相关处理,完成高精度开环多普勒测量。其特色在于完全不需要精确的先验轨道模型。所开发的专用被动式多普勒测量设备,在国内第一次成功用于欧空局环火星探测器“MEX”的多普勒测定轨试验。探测器X频段信号5s积分的单程多普勒测量精度达到 0.2mm/s ,与欧空局测量水平相当。采用该多普勒测量数据的MEX定轨结果与欧空局精密轨道在数百米至千米量级一致。