全文获取类型
收费全文 | 1289篇 |
免费 | 279篇 |
国内免费 | 135篇 |
专业分类
航空 | 949篇 |
航天技术 | 338篇 |
综合类 | 152篇 |
航天 | 264篇 |
出版年
2024年 | 4篇 |
2023年 | 31篇 |
2022年 | 24篇 |
2021年 | 50篇 |
2020年 | 56篇 |
2019年 | 47篇 |
2018年 | 41篇 |
2017年 | 62篇 |
2016年 | 65篇 |
2015年 | 59篇 |
2014年 | 100篇 |
2013年 | 74篇 |
2012年 | 88篇 |
2011年 | 103篇 |
2010年 | 83篇 |
2009年 | 123篇 |
2008年 | 111篇 |
2007年 | 91篇 |
2006年 | 115篇 |
2005年 | 82篇 |
2004年 | 46篇 |
2003年 | 45篇 |
2002年 | 25篇 |
2001年 | 24篇 |
2000年 | 26篇 |
1999年 | 18篇 |
1998年 | 20篇 |
1997年 | 27篇 |
1996年 | 16篇 |
1995年 | 12篇 |
1994年 | 10篇 |
1993年 | 9篇 |
1992年 | 3篇 |
1991年 | 3篇 |
1990年 | 4篇 |
1989年 | 3篇 |
1988年 | 1篇 |
1984年 | 1篇 |
1981年 | 1篇 |
排序方式: 共有1703条查询结果,搜索用时 15 毫秒
81.
针对短时高温抗氧化的具体环境,采用先驱体转化工艺制备2D Cf/SiC-Si复合材料.首先考察首周期裂解温度对2D Cf/SiC-Si材料力学性能的影响,结果表明,首周期采用1200℃裂解,所制备的2D Cf/SiC-Si复合材料界面结合较好,弯曲强度和断裂韧性分别达到305.4MPa和15.7 MPa·m1/2.在此基础上研究了Si粉含量对材料性能的影响.结果表明,随着Si含量的增加,2D Cf/SiC-Si材料的力学性能稍有降低,而抗氧化性能明显提高,主要原因在于材料中游离碳含量的降低和Si氧化后生成的具有封填裂纹和隔氧作用的SiO2膜. 相似文献
82.
高强Al-Cu-Li-X铝锂合金2A97三级时效工艺及性能研究 总被引:2,自引:0,他引:2
以新型高强Al-Gu-Li-X铝锂合金2A97为研究对象,通过拉伸试验研究两种三级时效工艺及其改型工艺对合金性能的影响.结果表明,含有δ′相二次析出过程的三级时效和含有δ′相回溶过程的三级时效处理合金的强度和塑性达到T6峰值时效水平,三级时效改型工艺由于增加变形使前者合金的强度升高,塑性降低,使后者的强度显著提高.三级时效和单级时效合金的主要显微组织有δ′相、θ″/θ′相和T1相.三级时效改型工艺由于增加变形促进δ′相析出和δ′相回溶,同时变形促进T1相析出,从而改变了主要强化相δ′相和T1相的数量. 相似文献
83.
多层钎焊结构件超声C扫描信号特征分析 总被引:1,自引:0,他引:1
对多层钎焊件内层焊缝检测中产生的多重声束路径叠加现象进行了详细分析,并用计算机模拟超声检测中的叠加信号,总结出对等厚薄板钎焊缝阵结构内层焊缝的检测方法及C扫描时信号门放置的合理位置,并且在实际检测中验证了该方法的正确性. 相似文献
84.
对2 mm厚的01420铝锂合金薄板实现了搅拌摩擦焊接(FSW),分析焊接接头的微观组织形态,研究焊接工艺参数对搅拌摩擦焊接接头成型和接头性能的影响,并与氩弧焊接接头性能相比较.结果表明,当工艺参数选取得当时,焊缝成型较好,表面光洁,焊接接头的强度可达到母材强度的77%,接头的弯曲角可达到180°,均高于氩弧焊接接头. 相似文献
85.
86.
介绍了蜂窝环形构件微型点焊的电极、设备及工艺过程,分析了焊点质量,发现了条形蜂窝件的质量问题对点焊过程的影响,并提出了相应的解决措施。 相似文献
87.
研究了添加剂含量对MoSi2发热体性能的影响,使用SEM观察各种添加剂含量试样的微观组织,测定各种添加剂含量试样的氧化动力学曲线、致密度、烧损温度。 相似文献
88.
基于有限元方法对不同搅拌头平移速度下搅拌摩擦焊接过程中焊接构件Al6061-T6材料的三维流动问题进行分析,研究了搅拌头平移速度的变化对等效塑性应变的分布和材料流动的影响。结果表明,搅拌头前方的材料向上涌起,被旋推到搅拌头后方并开始向下运动,这一过程是促使搅拌摩擦焊接顺利完成的主要原因。材料的等效塑性应变等值线与不同焊接区域的边界具有较好的对应关系。随着搅拌头平移速度的增加,垂直于焊缝方向上的截面上,等效塑性应变减小,但是材料的流动速度会随之增加。较低的搅拌头平移速度有利于焊缝中心线两侧材料的融合。 相似文献
89.
SU Xiang-donga b WANG Tian-minb * HAO Wei-changa HE Lib aCenter of Materials Physics Chemistry Beijing University of Astronautics Aeronautics Beijing China bGuizhou Academy of Science Guiyang China 《中国航空学报》2006,19(Z1)
The corrosion behavior of the nitinol alloy was studied in various corrosion media of different Cl–ion concentrations. The results demonstrate that the Cl–ion concentration has significant influences on the corrosion behavior of the nitinol alloy. In order to enhance the corrosion resistance, protective films were generated on the surface of the nitinol alloy by means of the electrochemical passivation method, for which five different electrolytic solutions were investigated. The surface analysis indicates full growth of all samples pas-sivated in the different electrolytic solutions with layers, however, showing different morphological features. Without any defects like micro-cracks and pores, the surface of the samples passivated in the molybdate solution turns out smoother and denser than those pas-sivated in other solutions. It is shown that the electro-chemical passivation will reduce Ni content but increase Ti content in the surface, reaching the Mole ratio of Ti:Ni=9.01:1 on the outermost surface. Potentiodynamic polarization test demonstrates that the samples electrochemically passivated in the molybdate solution present a significant increase in breakdown potential due to titanium enrichment on the outermost surface. 相似文献
90.