电缆支座承受径向载荷时的弹塑性分析

采用ANSYS软件对发动机电缆支座几种不同结构方案及其承载能力进行了三维有限元分析。考虑了材料的非线性弹塑性行为，计算给出了电缆支座承载能力，与试验结果比较吻合。     

价格弹性系数与总收益关系的理论探讨和应用

当商品需求富有弹性时,价格与总收益成反方向变化;当需求缺乏弹性时,价格与总收益成同方向变化。本文证明了这个结论还需满足一些条件,并指出了这些条件和新结论的意义。     

Active Aerothermoelastic Control of Hypersonic Double-wedge Lifting Surface

Designing re-entry space vehicles and high-speed aircraft requires special attention to the nonlinear thermoelastic and aerodynamic instability of their structural components. The thermal effects are important since temperature environment brings dramatic influences on the static and dynamic behaviors of flight structures in supersonic/hypersonic regimes and is likely to cause instability, catastrophic failure and oscillations resulting in structural failure due to fatigue. In order to understand the dynamic behaviors of these ＂hot＂ structures, a double-wedge lifting surface with combining freeplay and cubic structural nonlinearities in both plunging and pitching degrees-of-freedom operating in supersonic/hypersonic flight speed regimes has been analyzed. A third order piston theory aerodynamic is used to estimate the applied nonlinear unsteady aerodynamic loads. Also considered is the loss of torsional stiffness that may be incurred by lifting surfaces subject to axial stresses induced by aerodynamic heating. The aerodynamic heating effects are estimated based on the adiabatic wall temperature due to high speed airstreams. As a recently emerging technology, the active aerothermoelastic control is aimed at providing solutions to a large number of problems involving the aeronautical/aerospace flight vehicle structures. To prevent such damaging phenomena from occurring, an application of linear and nonlinear active control methods on both flutter boundary and post-flutter behavior has been fulfilled. In this paper, modeling issues as well as numerical simulation have been presented and pertinent conclusions outlined. It is evidenced that a serious loss of torsional stiffness may induce the dynamic instability; however active control can be used to expand the flutter boundary and convert unstable limit cycle oscillations （LCO） into the stable LCO and/or to shift the transition between these two states toward higher flight Mach numbers.     

利用气动弹性的柔性振翼模型建立及分析(英文)

Making use of modal characteristics of the natural vibration of flexible structure to design the oscillating wing aircraft is proposed. A series of equations concerning the oscillating wing of flexible structures are derived. The kinetic equation for aerodynamic force coupled with elastic movement is set up, and relevant formulae are derived. The unsteady aerodynamic one in that formulae is revised. The design principle, design process and range of application of such oscillating wing analytical method are elaborated. A flexible structural oscillating wing model is set up, and relevant time response analysis and frequency response analysis are conducted. The analytical results indicate that adopting the new-type driving way for the oscillating wing will not have flutter problems and will be able to produce propulsive force. Furthermore, it will consume much less power than the fixed wing for generating the same lift.     

弹性高超声速滑翔飞行器的状态/参数联合估计

弹性高超声速滑翔飞行器具有强非线性、强不确定性和刚体/弹性耦合的特点，对其状态和参数进行估计十分必要。为解决这一问题，提出了一种传感器布置策略和一种利用正交三角（QR）分解更新到达代价的滚动时域估计算法（MHE-QR）。首先，建立了考虑弹性的传感器观测模型并分析了传感器位置对可观性的影响，并在此基础上提出了一种反映系统可观性的性能指标。传感器布置策略以此性能指标为目标函数，将传感器布置问题转化为约束非线性优化问题并求解，即可得到最优传感器布置方案。然后提出了MHE-QR算法。在滚动时域估计的框架下，该算法利用前向动态规划原理将到达代价的计算转化为最小二乘问题，并给出了基于QR分解的到达代价更新算法。仿真结果表明该传感器布置策略和MHE-QR算法能够有效提高估计精度、收敛速度和计算速度。此外，MHE-QR算法具有实时应用的潜力。     

飞机上偏心衬套的更换方法

飞机接头上的偏心衬套由于磨损或有故障需要更换。本文介绍了偏心村套的更换方法。     

弹性O型圈密封技术概述

弹性Ｏ型密封圈用于密封流体防止泄漏已有逾６０年的历史。本文就这种形式的密封圈及相关密封技术作一综合性论述，重点在它的选取，设计和防护以及密封技术的发展状况。     

SMA拟橡胶金属阻尼元件及其在减振中的应用

利用形状记忆合金(SMA,Shape Memory Alloys)的超弹性特性,借鉴拟橡胶金属阻尼材料的制作工艺,研制了超弹性SMA拟橡胶金属阻尼元件;在此基础上,设计了SMA减振器.试验表明:引入SMA后,拟橡胶金属减振器的可恢复变形,阻尼特性都有很大的提高;而拟橡胶金属的构造方式,又使得减振器具有很大的承载能力.上述特性使得该减振器对于宽频带随机载荷有很好的减振效果.      

不同振动形式下的翼型失速特性

通过求解雷诺平均Navier-Stokes方程,研究了翼型在强迫振动和自然结构振动下的大迎角流场特性,尤其是失速迎角附近的流场和气动特性.研究结果表明:在接近颤振临界速度情况下结构自然振动可以引起翼型大尺度的分离,导致失速分离涡提前出现;强迫性的沉浮运动和俯仰运动在一定幅度下也可以引起失速性质的大分离,而且沉浮和俯仰振动的频率和振幅都是影响翼型大尺度分离的重要因素.     

基于零点配置的分力合成主动振动抑制方法研究(英文)

The component synthesis active vibration suppression method （CSVS） can be applied to suppress the vibration of flexible systems. By this method, several same or similar time-varying components are arranged according to certain rules along the time axis. The synthesized command can suppress the arbitrary unwanted vibration harmonic while achieving the desired rigid body motion. The number of the components increases rapidly when the number of harmonic vibration is growing. In this article, the CSVS based on zero-placement technique is used to construct the synthesized command to suppress the multi-harmonics simultaneously in the discrete domain. The nature of zero-placement method is to put enough zeros to cancel system poles at necessary points. The designed synthesized command has equal time intervals between each component and which is much easier to be implemented. Using this method, the number of components increases linearly with the increasing of the number of being suppressed harmonics. For the spacecraft with flexible appendages, CSVS based on zero-placement is used to design the time optimal large angle maneuver control strategy. Simulations have verified the validity and superiority of the proposed approach.