2DCf／SiC-Si复合材料的制备和性能研究

针对短时高温抗氧化的具体环境,采用先驱体转化工艺制备2D Cf/SiC-Si复合材料.首先考察首周期裂解温度对2D Cf/SiC-Si材料力学性能的影响,结果表明,首周期采用1200℃裂解,所制备的2D Cf/SiC-Si复合材料界面结合较好,弯曲强度和断裂韧性分别达到305.4MPa和15.7 MPa·m1/2.在此基础上研究了Si粉含量对材料性能的影响.结果表明,随着Si含量的增加,2D Cf/SiC-Si材料的力学性能稍有降低,而抗氧化性能明显提高,主要原因在于材料中游离碳含量的降低和Si氧化后生成的具有封填裂纹和隔氧作用的SiO2膜.     

MSC/NASTRAN在复合材料层压板屈曲分析中的应用

介绍了MSC/NASTRAN的特征值屈曲分析的方法,并通过有限元建模样详细说明了-个典型复合材料层压平板屈曲分析算例,与经典复合材料层压板的理论计算结果吻合良好.     

环形编织层板冲击包容数值模拟

为分析航空发动机复合材料机匣对破断叶片的包容,采用有限元仿真方法开展了计算研究。通过旋转体与机匣冲击破坏过程的计算,确定机匣的包容能力。基于具备显式求解功能的商用有限元软件Abaqus/Explicit,采用3维实体单元网格,将2维3轴编织的碳纤维层合材料简化成连续的正交各向异性材料,通过软件提供的Vumat用户子程序接口编写Fortran代码定义材料模型,计算与转轴分离后的模拟断裂叶片对机匣的冲击过程。通过冲击后的临界转速和能量吸收数据,比较了模拟计算与实物旋转冲击模拟试验的结果,二者具有较大的可比性。虽然计算中还缺乏材料基本性能表征的理想数据,但在多种工况下仿真计算表明模拟结果稳定,有望成为复合材料包容分析实用有效的方法。     

基于CFD/CSD方法的蜻蜓柔性翼气动特性分析

给出了一种基于计算流体力学/计算结构力学（CFD/CSD）的双向流固耦合方法.通过交替数字二叉树（ADT）搜索技术识别流固网格之间的宿主-受体关系.采用局部插值算法完成两套网格系统之间的数据交换,并使用Delaunay图映射方法来完成气动网格的移动.将自编的非线性结构有限元程序、接口程序与南京航空航天大学（NUAA）微型飞行器中心的流体计算程序3D2MUFS相连接,应用于蜻蜓柔性翼拍动飞行的气动计算中.计算结果表明:柔性变形使得蜻蜓翼的时均举力系数从0.31提高到0.53,时均推力系数从0.07提高到0.13,证实了柔性变形能改善扑翼的气动性能.      

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

多重纳米结构轻质高强铝基复合材料的制备和组织性能

为了研究多重纳米结构对块体材料强化和变形能力的影响机制,采用粉末冶金法制备了多重纳米结构的B4C颗粒增强铝基复合材料,并对复合材料的强化和形变破坏机制进行了定量和定性的讨论。由100%球磨复合粉末制备的块体复合材料的室温压缩强度为670MPa;当加入10vol%气雾化态的Al2024粉末后,复合材料的室温压缩强度升高到1.115GPa;之后随着气雾化态Al2024粉末含量的增加,复合材料的强度逐渐下降,但是没有产生明显的塑性变形;当气雾化态Al2024粉末的含量增加到50vol%时,复合材料的压缩强度下降到580MPa,断裂前变形率达到了10%。扫描电镜(SEM)和透射电镜(TEM)的分析结果显示,亚微米级的B4C颗粒、位错以及纳米晶基体分别通过Orowan强化、位错强化和细晶强化机制对复合材料进行强化;粗晶Al2024区域与复合结构区域的比例显著影响复合材料的形变及破坏机制。     

面内弯曲载荷作用下两边简支两边固支复合材料层合板的屈曲

为扩充航空复合材料结构稳定性设计手段,基于Levy形式级数和有限差分法,提出了面内纯弯曲载荷作用下两边简支两边固支（SSCC）复合材料层合板临界屈曲载荷的数值解法。首先,应用有限差分法将挠度函数进行离散化处理;然后利用边界条件扩充方程组,最后将临界屈曲载荷的求解转化为广义特征值问题。通过数值算例分别在各向同性板和复合材料层合板上验证了本文方法,并与有限元方法（FEM）进行了比较。结果表明,本文方法具有很高的精度,为复合材料层合板的屈曲分析开辟了新的途径。     

压辊材料及形状对纤维铺放压紧效果的影响

近年来纤维铺放（AFP）技术被广泛用于大型复杂飞机复合材料构件成型。为了保证纤维铺放过程的一致性,纤维铺放压辊必须在适应芯模型面的同时具有较好的压紧力分布均匀性。鉴于此,对不同弹性模量的压辊材料进行了试验分析,薄膜压力传感器及超声显微镜测试结果表明,低弹性模量的压辊材料变形较大,较好地适应了芯模表面,压力分布相对均匀且可以减少铺层的层间孔隙数量,硅橡胶压辊比聚乙烯压辊压紧力分布均匀性提高了50%~60%,铺层孔隙率降低了92.1%。针对孔隙分布主要集中在压辊两端及压紧力在压辊两端下降幅度较大的问题,采用ANSYS Workbench对压辊端部进行斜端面优化,得到最优倾斜角度为20°;测试结果表明斜端面压辊压力分布均匀性比直断面压辊提高了42.9%,铺层孔隙率下降了51.6%。     

Determination of thermal expansion coefficients for unidirectional fiber-reinforced composites

In the present work, the coefficients of thermal expansion（CTEs） of unidirectional（UD）fiber-reinforced composites are studied. First, an attempt is made to propose a model to predict both longitudinal and transverse CTEs of UD composites by means of thermo-elastic mechanics analysis. The proposed model is supposed to be a concentric cylinder with a transversely isotropic fiber embedded in an isotropic matrix, and it is subjected to a uniform temperature change. Then a concise and explicit formula is offered for each CTE. Finally, some finite element（FE） models are created by a finite element program MSC. Patran according to different material systems and fiber volume fractions. In addition, the available experimental data and results of other analytical solutions of CTEs are presented. Comparisons are made among the results of the cylinder model,the finite element method（FEM）, experiments, and other solutions, which show that the predicted CTEs by the new model are in good agreement with the experimental data. In particular, transverse CTEs generally offer better agreements than those predicted by most of other solutions.     

柔性热膜剪应力传感器水下测量温度修正

柔性热膜微传感器应用于流体壁面剪应力测量时,流体温度对传感器输出有很大影响,因此有必要对工作在非标定温度下的传感器输出信号进行修正补偿。重点研究了水下测量时传感器输出与水温的关系以及温度修正方法。通过分析传感器过热比和流体物理性质与温度的相关性,建立了流体温度与传感器过热比和标定系数的函数关系。在此基础上,提出了一种用于水下剪应力测量的温度修正方法,可以有效减小水温对传感器输出的影响。经实验验证,该方法可以使工作在25℃、28℃水温环境下的传感器输出值与其20℃标定值的相对误差从23．7％和37．1％回落到0．82％和0．83％。