基于CFD高精度算法的雷电电磁场研究

雷电空间电磁场一直是电磁领域研究的热门，成熟的算法例如有限时域差分法（FDTD），传输线矩阵法（TLM）以及频域的矩量法（MoM）在计算雷电问题方面都有广泛的应用。由于计算流体力学（CFD）中的Euler方程与电磁学中的Maxwell方程有着相同的守恒形式，而且采用间断伽辽金方法（DG）已经在流场问题上得到广泛的尝试，因此引入了基于计算流体力学的DG方法来离散时域Maxwell方程，并采用网格分区并行技术加速计算，使用基于DG的圆球雷达散射截面积（RCS）算例进行测试，数值结果一致表明DG算法在求解电磁场问题上的可行性，之后通过计算一段近场雷电通道的电场分布并与解析解、某算法仿真解对比，数据基本吻合，说明该方法适合于雷电电磁场的计算。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Fault mode probability factor based fault-tolerant control for dissimilar redundant actuation system

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model precision and computation time, a Moving Window (MW) method is used to determine the applied historical statistics. The FMPF based FTC strategy is developed for the amended system model where the system estimation and Linear Quadratic Regulator (LQR) are updated at the end of system sampling period. The simulations of DRAS system subjected to multiple faults have been performed and the results indicate the effectiveness of the proposed approach.     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

Accurate approximation of in-ecliptic trajectories for E-sail with constant pitch angle

Propellantless continuous-thrust propulsion systems, such as electric solar wind sails, may be successfully used for new space missions, especially those requiring high-energy orbit transfers. When the mass-to-thrust ratio is sufficiently large, the spacecraft trajectory is characterized by long flight times with a number of revolutions around the Sun. The corresponding mission analysis, especially when addressed within an optimal context, requires a significant amount of simulation effort. Analytical trajectories are therefore useful aids in a preliminary phase of mission design, even though exact solution are very difficult to obtain. The aim of this paper is to present an accurate, analytical, approximation of the spacecraft trajectory generated by an electric solar wind sail with a constant pitch angle, using the latest mathematical model of the thrust vector. Assuming a heliocentric circular parking orbit and a two-dimensional scenario, the simulation results show that the proposed equations are able to accurately describe the actual spacecraft trajectory for a long time interval when the propulsive acceleration magnitude is sufficiently small.     

某型装备能源电池异常爆破故障分析

对一起因电池设计缺陷引发装备战训失利的故障进行分析,重点对电池工作机理和设计缺陷展开解析,明确故障定位,并对国内外装备弹上不同体系电池的优缺点进行比较,旨在为产品维护保障、国产化科研等工作提供参考。     

航空电子产品电磁环境效应模块化设计方法

对高强度辐射场（HIRF）环境特点与干扰类型进行分析，采用理论计算、计算机仿真技术（CST）的仿真分析及实测等方法分别对某型飞机航空电子系统综合显示单元的外部强电磁辐射场孔缝耦合、场线耦合及芯片前端电路影响关键芯片的相关规律进行了研究，给出了相关设计建议。结果表明，可通过分析孔缝、场线耦合获得进入关键芯片前端电路的电磁干扰能量，再结合关键芯片前端电路网络对干扰的插入损耗分析，获得关键芯片在外部强场激励下的感应电压。     

预测悬停旋翼跨音速流动的一种组合自由尾流/CFD方法

一种新的组合自由尾流 / CFD方法用于悬停旋翼流动的 CFD解中以考虑实际尾流的作用 .用文中描述的尾流分析方法研究了螺旋尖涡的运动 .首先从广义尾流模型开始 ,用半经验公式模化了涡核对旋翼尾流的作用 ;然后在环量收敛和尾迹收敛的条件下完成了自由尾迹计算 ;最后应用 Jameson有限体积龙格 -库塔推进格式求解了欧拉方程 .所得结果与相关文献和实验数据进行了比较     

燃烧火焰温度分布重建结果误差分析

分析了采用辐射型CT算法的燃烧火焰温度发布重建结果误差产生的原因，给出了解决方法。     

行星际结构与准平行无碰撞激波的相互作用

应用一维混合模拟方法数值研究了高密度等离子体团和行星际激波与准平行无碰撞激波的相互作用．结果表明，由于推平行无碰撞激波上游的大振幅低频波动的散射，除了在通过激波过渡区时稍有压缩外，等离子体团从激波的上游开始就一直是不断弥散的．行星际激波在向准平行无碰撞激波靠近的过程中，会在其上游产生大振幅的低频波动，同时行星际激波的强度不断增加，最后和准平行无碰撞激波会并成一个新的激波，在新激波前继续有大振幅的低频波动产生