基于分级优化的飞机翼面结构布局综合技术研究

为了探讨飞机翼面结构主要纵横骨架的最佳布局问题．并提供符合工程实际的、用于概念设计阶段的飞机结构设计方法,本文采用分级优化与集成的策略,该策略分为三个层次。第一个层次为拓扑优化,并由此确定纵向骨架的个数与位置的最优布局;第二个层次为尺寸优化,它用来确定翼面的中间参数;第三个层次为稳定性准则优化,它确定横向骨架的个数与位置的最优布局。在分级优化的三个层次中,拓扑优化是独立的,尺寸优化与稳定性准则优化是相互耦合的。以国外某飞机机翼为例,结果表明本文提出分级优化的思路与所采用的集成方法是可行的,并且具有很好的数值效果。作者认为：它对从事飞机结构设计的人员有一定的指导性和参考价值,值得在飞机设计部门推广应用。最后,总结给出五点结论供参考。     

含多处损伤未加筋铝合金壁板的剩余强度

 进行了含多处损伤（MSD）的未加筋LY12CZ铝合金壁板的剩余强度试验。用0.12的钼丝切割预制裂纹,在垂直于裂纹面的方向施加单调增加的拉伸载荷,直至壁板破坏。得到了含不同裂纹几何的未加筋壁板的剩余强度。试验结果表明随着主裂纹长度增加,未加筋壁板的剩余强度减小;对相同的主裂纹长度,主裂纹和相邻的MSD裂纹之间的距离b减小,平板的剩余强度也减小。用5种失效准则分别计算了每个壁板的剩余强度。与试验结果的比较表明,净截面屈服准则和表观断裂韧性准则的误差较大,塑性区连通准则预测的平均误差为22.17%,改进的表观断裂韧性准则的平均误差为16.98%,而改进的塑性区连通准则预测的平均误差为8.27%,改进的塑性区连通准则大大提高了预测结果的精度。     

航空发动机高压转子试验模型的动力学相似设计

为了获得能够替代航空发动机转子原型进行动力学试验的模型，提出了发动机转子系统试验模型的动力学相似设计方法。采用相似理论推导了转子系统缩比模型的动力学相似准则，继而建立缩比模型与原型的动力学相似关系。通过动力学优化方法对转子缩比模型的动力学等效模型进行修正，目标函数由固有频率、临界转速和振型组成。以双转子发动机高压转子系统的动力学相似设计为例，通过有限元仿真对设计方法的有效性进行了验证。结果表明，在设计转速范围内，动力学相似模型与原型的前两阶临界转速相似误差分别为3.92%和0.86%，对应振型的相关性均大于0.98，且模型与原型的模态应变能分布基本一致。通过该方法获得的动力学相似模型能够较好地预测原型的动力学特性，并有效降低模型试验的成本和难度。     

Hydro-geomorphic characteristics of the Indian (Peninsular) catchments: Based on morphometric correlation with hydro-sedimentary data

In terms of hydro-geomorphic characteristics, catchments in Peninsular India remained mostly unexplored except a few regional and local works that deal with tectonic, structural and paleo-climatic control on geomorphology. Catchment scale morphometric analyses deliver insights into dynamics, erosion capacity, probability of flood occurrence, lithological and structural control, and genetic response to the tectonics. The present study aimed to comprehend hydro-geomorphic characteristics of 12 major catchments in Peninsular India through GIS-based morphometric analysis. A total of 25 morphometric parameters were computed and several statistical analyses performed in establishing inter-correlation and classification of Indian rivers. Most of the rivers in Peninsular India were found 7th to 9th order catchments. Almost all basins showed a moderate relief ratio, hypsometric integral, ruggedness etc. Cauvery, Baitarni, and Brahmani showed exceptionally steeper gradient, high relief ratio, LS factor, and ruggedness index, which indicated higher erosion potential. Correlation among landscape variables revealed moderate scale dependency of few relief factors. Baitarni, Brahmani and Narmada showed higher hypsometric integral. A strong positive association between hypsometric integral and sediment yield suggested critically high erosion potential in catchments with high integral values. The present study provides some generic insights into the hydro-geomorphic characteristics with dissimilarity in lithology in Peninsular Indian catchments as a whole.     

Cross-sectional deformation of H96 brass double-ridged rectangular tube in rotary draw bending process with different yield criteria

Different yield criterion has great difference in predicting the deformation of tube with different material. In order to improve the prediction accuracy of the cross-sectional deformation of the double-ridged rectangular tube (DRRT) during rotary draw bending (RDB) process, Mises isotropic yield criterion, Hill’48 and Barlat/Lian anisotropic yield criteria commonly used in practical engineering are introduced to simulate RDB of DRRT. The inverse method combining uniaxial tensile test of whole tube and response surface methodology was proposed to identify the parameters of Hill’48 and Barlat/Lian yield criteria of small-sized H96 brass extrusion DRRT as well. Then based on ABAQUS/Explicit platform, the FE models of RDB process of DRRT considering Mises, Hill’48 and Barlat/Lian yield criteria were built. The results show that: The variation trend of cross-sectional deformation ratio is same when using different yield criteria. The cross-sectional deformation ratio by using Mises yield criterion is close to that by using Hill’48 yield criterion. However, there is a quite difference between by using Barlat/Lian yield criterion and by using Mises or Hill’48 yield criteria. The prediction values of cross-sectional height deformation by using three yield criteria all underestimate the experiment ones, and the prediction values of cross-sectional width deformation overestimate the experiment ones. By comparing the simulation results of cross-sectional deformation of the DRRT with different yield criteria and experiment ones, Barlat/Lian yield criterion is found to be suitable for describing the RDB process of DRRT.     

电传直升机人机耦合振荡特性研究

为了分析研究电传直升机的人机耦合振荡特性,将直升机操纵/响应模型与驾驶员诱发振荡(Pilot Induce Oscillation,PIO)判定准则模型相结合,建立了一种适用于电传直升机的PIO预测方法。首先对建立的方法进行了飞行试验验证,然后应用该方法着重开展了PIO参数敏感性分析研究,得到了对降低PIO趋势有指导意义的结果。     

直流电弧等离子体炬电极烧蚀特性分析及实验测量

为研究直流电弧等离子体发生器电极烧蚀特性，进而为其寿命评估提供依据，对直流电弧电极烧蚀特性进行了分析，探究电极烧蚀率的主要影响因素并推导了相关准则数。搭建了电极烧蚀实验系统，对钨电极烧蚀特性进行了实验研究。结果表明:在相同输入功率下，电弧放电过程中阴极与阳极的烧蚀率基本相同且不随时间变化，如2.2 kW时，烧蚀率保持13.88 mg/s不变;在实验功率范围内，电极烧蚀率与输入功率近似呈三次函数关系。利用之前推导的准则数，建立了计算烧蚀率的实验关联式。     

Solar extreme events on the data of Alma-Ata neutron monitor: Identification of ground level enhancements

Ground level enhancements of cosmic ray intensity registered by means of neutron monitors at middle latitudes were studied by using Student’s criterion. Three of these events on 6 November 1997, 24 August 1998, and 13 December 2006 were analyzed in detail. It is shown that the use of Student’s criterion allows revealing effectively the ground level enhancements at middle latitudes.     

微束等离子焊接

简要介绍了微束等离子焊接的工艺设备。通过对乌克兰巴顿焊接研究所几个实例的介绍，较全面地阐述了微束等离子焊接工艺方案、焊接设备的各项技术要求和特性。与氩弧焊、激光焊进行了比较，认为微束等离子焊接具有电弧收缩、能量集中、适用于薄壁件焊接的特点，在我国具有广阔的应用前景。     

格尼襟翼在冰风洞混合翼设计中的应用

提出面向工程、面向适航的混合翼设计准则,基于此准则提出将格尼襟翼应用于民机机翼结冰风洞试验的单段混合翼设计中。设计准则中只对驻点位置和前缘吸力峰值提出保守性要求,易于工程实现,满足结冰适航要求。对于偏离设计点较大的状态,在单段混合翼后缘添加格尼襟翼并配合迎角调整,使得单段混合翼在此状态点处仍满足设计准则。这样使得单段混合翼也能应用于试验状态比较广的结冰风洞试验中。格尼襟翼的使用,降低了混合翼设计、试验费用,为民机结冰试航取证节约了时间。