圆柱尾流中的二次分离及环量衰减问题

在圆柱绕流的非定常流动中,相应于旋涡的周期性脱落柱后的二次分离是周期性间断发生。二次涡的影响不能忽略。但对长时间流动的模拟还必须考虑尾涡的环量衰减。模拟Bluff Body流动有效的离散涡模型应包括二次分离及尾涡衰减两种机因。本文数值计算结果证明了上述结论。     

Effect of tip geometry and tip clearance on aerodynamic performance of a linear compressor cascade

The tip leakage flow between a blade and a casing wall has a strong impact on compressor pressure rise capability, efficiency, and stability. Consequently, there is a strong motivation to look for means to minimize its impact on performance. This paper presents the potential of passive tip leakage flow control to increase the aerodynamic performance of highly loaded compressor blades. Experimental investigations on a linear compressor cascade equipped with blade winglets mounted to the blade tips have been carried out. Results for a variation of the tip clearance and the winglet geometry are presented. Current results indicate that the use of proper tip winglets in a compressor cascade can positively affect the local aerodynamic field by weakening the tip leakage vortex. Results also show that the suction-side winglets are aerodynamically superior to the pressure-side or combined winglets. The suction-side winglets are capable of reducing the exit total pressure loss associated with the tip leakage flow and the passage secondary flow to a significant degree.     

低负荷弯叶栅流谱结构与气动性能的实验研究

在一套典型的低负荷矩形涡轮静叶栅中开展弯叶片影响叶栅内部流谱结构与气动性能的实验研究。利用微型5孔探针分别对6套叶栅的进出口流场进行详细测量,并在叶栅表面和端壁进行油流显示实验。从定性和定量的角度考察了叶片弯曲对壁面流谱拓扑结构、出口涡量、出气角及二次流损失分布的影响,总结了弯叶片影响边界层迁移与二次流损失发展的规律。     

涡破裂诱导的垂尾抖振气动弹性分析

通过试验方法分析了三角翼前缘分离涡与垂尾抖振之间的关系,深入研究了尾迹流动对垂尾抖振各阶模态的激励作用。计算得到了垂尾模型固有频率及各阶模态。在风洞试验中,应用激光片光烟流场显示技术,得到了三角翼模型在风速为30 m/s下,各迎角的涡结构;使用加速度传感器测量了垂尾翼根和翼梢的抖振响应;使用热线风速仪测量了垂尾翼根和翼梢位置的脉动速度分量。结果表明:前缘涡破裂后产生的高湍流度的尾迹是垂尾抖振的直接原因,抖振边界与涡破裂的强度和位置有关;涡破裂后尾迹与垂尾产生共振,使得抖振加速度响应频率与垂尾固有频率一致;涡破裂后,在较小迎角下,尾迹对垂尾的高频振动模态的激励较为明显,在较大迎角下,涡破裂流动对垂尾低频振动模态的激励加强了。     

前置隔板对圆柱绕流影响的实验分析

对经典的圆柱绕流模型,运用前置隔板对流场进行控制。利用粒子图像测速(PIV)方法在自循环水槽中研究了雷诺数为1 800时,柔性和刚性2种不同刚度的前置隔板对圆柱绕流的影响。研究发现:柔性隔板自由端的弯曲增加了对流场的额外扰动,并且柔性隔板弯曲变形会诱导产生脱落涡,导致尾迹流场的主频发生变化。在圆柱下游流场,无隔板工况与柔性隔板工况的回流区长度相当,刚性隔板工况的回流区相较之下则更长。结果显示:前置隔板还能在一定程度上减小圆柱绕流的阻力。      

基于流动显示的翼尖涡不稳定频率测量

翼尖涡涡核振荡频率的准确测量是翼尖涡控制技术得以有效实施的重要前提。采用流动显示方法,研究了椭圆机翼翼尖涡在低雷诺数条件下的不稳定特性。分别采用单点谱分析和动力学模态分解技术,从流动显示图像序列中提取了涡核振荡的短波不稳定模态的频率,2种方法得到的频率相对误差最大不超过5%。研究结果表明:涡对的空间运动通常展现出长波与短波模态的耦合,涡核的高频短波振荡耦合在低频长波摆动中,以前者为主要含能模态;短波不稳定性的无量纲振荡频率随雷诺数的增大而增大、随机翼攻角的增大而减小。      

Design and Performance of an Improved Trapped Vortex Combustor

 A trapped vortex combustor (TVC) has been a very promising novel concept for it offers improvements in lean blow out, altitude relight, operating range, as well as a potential to decrease NO_x emissions compared to conventional combustors. The present paper discusses the improved designs of the new combustor over the prior ones of our research group, including that: a) the overall dimensions, both axial and radial, are reduced to those of an actual aero-engine combustor; b) the air flow distribution is optimized, and especially 15% of the air is fed into the liner as cooling air; c) a straight-wall diffuser with divergence angle 9癷s added. A series of experiments (cavity-fueled only, under atmospheric pressure) has been conducted to investigate the performance of the improved TVC. Experimental results show that at the inlet temperature of 523 K, the inlet pressure of 0.1 MPa, stable operation of the TVC test rig is observed for the Mach number 0.15-0.34, indicating good flame stability; the combustion efficiency obtained in this paper falls into the range of 60%-96%; as the total excess air ratio increases, the combustion efficiency decreases, while the increase of the inlet temperature is beneficial to high combustion efficiency; besides, the optimal Mach numbers for high combustion efficiency under different inlet conditions are confirmed. The outlet temperature profiles feature a bottom in the mid-height of the exit. This paper demonstrates the feasibility for the TVC to be applied to a realistic aero-engine preliminarily and provides reference for TVC design.     

基于涡格法的近程无人机气动优化与风洞实验验证

针对低雷诺数的近程无人机,利用涡格法（VLM）对无人机气动特性进行了加装翼尖小翼优化设计,并通过风洞实验进行了验证。首先给出了翼尖小翼的几何参数并分析其对全机气动特性的影响,其次利用涡格法对小翼进行气动建模和优选,针对无人机巡航状态给出了小翼优化结果,最后利用风洞实验对优化前后的无人机进行了吹风实验对比验证,实验结果表明,涡格法和风洞实验结果在线性段相符,涡格法能够较准确地描述和预测翼尖小翼特性,加装翼尖小翼后的无人机巡航状态升阻比提高12％,全机滚转阻尼加大,偏航阻尼变化很小。     

用PIV技术研究四角切圆锅炉燃烧器区冷态燃烧流场的湍流积分尺度

四角切圆锅炉内煤粉的燃烧过程对提高锅炉运行效率及NOX减排有着显著的现实意义。通过搭建四角切圆锅炉冷态模型,利用粒子成像测速技（Particle Image Velocimetry）,采用空间相关分析方法,针对燃烧器区四角射流复杂湍流的涡拟序结构,开展基于湍流积分尺度来表征的3个典型水平层面涡尺度分布规律研究。通过对湍流积分尺度和时均速度的相关分析研究,认为冷态燃烧器区湍流涡尺度分布不仅与风口流速相关,同时还与风层位置密切相关,并不与风口流速呈线性变化规律,上一次风层涡尺度分布与其它两个风层的相比存在很大差异,因此湍流积分尺度的研究对煤粉高效洁净燃烧具有一定的理论指导意义。     

旋流数对分层旋流流场影响的大涡模拟研究

为了深入理解分层旋流流场特征和燃烧稳定性,采用OpenFOAM对分层旋流燃烧器的冷态和燃烧流场进行了大涡模拟。研究了旋流数对分层旋流流场结构和非稳态特性的影响。采用Q准则显示了流场中的瞬时涡结构;利用功率谱分析了流场中的进动特征。结果表明：在冷态工况下,旋流对回流区的位置和大小影响较小。随着旋流数增大,出口气流受到旋流诱导的离心作用,流动发散,流场扩张角变大,流场下游出现二次回流区。平均流场的三维流线与螺旋涡在空间中均表现成正交关系,表明螺旋涡是由剪切层Kelvin-Helmholtz不稳定性产生。在燃烧工况下,随着旋流数增大,回流区的面积增大,平均温度分布不断沿径向扩张,火焰锋面脉动增强,涡旋发生破碎的位置明显向上游移动。