喷丸强化10Ni3MnCuAl钢的表面性能

对10Ni3MnCuAl钢磨削表面进行不同强度的喷丸强化处理,分析了喷丸强化后10Ni3MnCuAl钢的金相组织及喷丸表层下微观结构的变化,测量了喷丸影响层的显微硬度以及喷丸强化所形成的残余压应力场, 研究了喷丸所造成显微硬度、金相组织和表面残余应力等表面完整变化.结果表明, 喷丸强化可显著改善10Ni3MnCuAl钢表面完整性及其疲劳寿命. 喷丸强度高时将产生过喷效应,导致疲劳寿命的降低,实验测得最佳喷丸强化弧高值为0.40 mm时表面质量最好,喷丸影响层的残余应力深度达450 μm.     

开孔变刚度层合板压缩屈曲性能研究

针对开孔变刚度层合板,建立3种尺寸的层合板有限元模型,采用了线性屈曲、引入残余热应力的线性屈曲和引入初始缺陷的非线性屈曲的3种分析方法,研究了开孔层合板在压缩条件下的屈曲行为,并通过自动铺丝制造层合板进行试验对比,对3种方法的合理性进行了分析。结果表明,引入残余热应力的线性屈曲分析方法与试验结果最吻合,两者仅相差0.63%。基于该方法,讨论开孔层合板残余热应力分布特点和应力水平,得出了开孔层合板的应力分布云图和应力分布规律,计算出残余热应力对开孔复合材料层合的屈曲影响。结果表明,残余热应力对传统直线开孔层合板的屈曲载荷影响很小,仅提高了3.57%,但大大提高了变刚度开孔层合板的屈曲载荷,最多可达23.40%。说明纤维曲线铺放可以改变内部残余热应力的分布,提高整个开孔层合板承载压缩载荷的能力。     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

Analytical solutions for Earth discontinuous coverage of satellite constellation with repeating ground tracks

This paper presents an analytical model for calculating the Earth discontinuous coverage of satellite constellation with repeating ground tracks by integrating and extending the application of coverage region and route theory. Specifically, the visibility condition for a ground point is represented as a coverage region in the two-dimension map of visibility properties, and the trajectories of satellites with circular orbits and repeating ground tracks are converted to several inclined lines in t...     

火星表面热环境对航天器热控影响分析

火星大气对太阳辐射产生吸收和散射作用,同时还将与火星表面航天器发生对流换热.热设计时难以直接评估对流、辐射和导热三种换热对航天器的影响,从而确定主要的控温途径.在调研火星表面辐射、大气等热环境的基础上,从线性化传热系数和对流辐射比的角度对比分析了辐射、对流和导热对航天器的影响.器表辐射传热系数随光学属性和温度的变化范围...     

模块化空间可展开天线支撑桁架结构的热-结构分析

对模块化空间可展开天线支撑桁架结构进行空间热交变环境下的热 结构分析,为天线结构因热致变形影响形面精度和网面稳定性提供合理的防护建议。采用ANSYS APDL有限元软件建立了大口径模块化空间可展开天线支撑结构的精细化数值模型,基于已有试验分别验证了模块化可展开天线结构有限元建模和热分析模型的正确性;分析了在瞬态温度场作用下约束位置等参数对支撑桁架弦杆及拉索应力的影响和热致变形规律。研究结果表明：空间可展开天线结构的应力和变形随时间历程发展与瞬态温度场变化趋势基本一致;同一瞬态温度场下,天线结构中心模块拉索热应力最大,同圈模块的弦杆热应力幅值基本相同,其上弦杆热应力逐圈增大,而拉索热应力逐圈减小;天线结构热致变形在距离约束最远端处整体累计值最大,上层中心点处累计热致变形可达15mm左右,对天线形面精度的影响不可忽略;将天线支撑桁架结构最外侧且距离结构中心最近的模块顶角和与相邻模块竖杆拼接处作为星载天线伸展臂约束时,天线结构的热致变形最小。将该处作为模块化空间可展开天线的展开支点,并建议对天线支撑结构表面采用涂刷隔热防护复合材料涂层等防护措施,以增加天线结构在太空极端环境的适应性,从而减小温度交变对天线整体形变和网面精度的影响。     

金属热防护系统多层隔热材料的传热分析及参数优化

采用能量平衡方程和离散坐标法近似地建立了金属热防护系统多层隔热材料的一维稳态传热的数学模型，并利用遗传算法和纤维隔热材料的有效导热系数试验数据求解传热反问题，从而得到了模型中的纤维隔热材料的辐射衰减系数、反照率和隔热屏表面辐射发射系数。最后，由实验测得了多层隔热材料的有效导热系数，验证了采用优化参数后，多层隔热材料的传热模型的正确性。     

血液及血液替代流体流变特性实验研究

发现和寻找一种透明的、流变特性与血液流体特性很好匹配的血液替代流体进行实验研究是非常迫切和必要的.运用美国brook 公司生产的 PVS Rheometer型旋流变仪对黄原胶溶液流变特性实验发现,黄原胶溶液是一种典型的剪切稀化流体,其剪切应力和剪切速率符合幂律分布;黄原胶溶液浓度越高,其剪切稀化特性越强;黄原胶溶液的表观粘度与溶液温度成反比,与溶液浓度成正比;人体血液的表观粘度介于0.4‰的黄原胶溶液(重量百分比)在温度为20℃和37℃之间的粘度值,在剪切速率介于10s-1~500s-1范围内,人体血液表观粘度随剪切速率的变化过程和0.4‰黄原胶溶液(温度30℃)基本重合.