MD-130 胶黏剂固化工艺及空间适用性研究

为满足航天电子产品的工艺实施和空间服役要求,本文详细开展了MD-130胶黏剂的固化工艺及空间适应性研究。结果表明,在150℃等温固化60 min后其拉伸剪切强度达到18 MPa,表明其为优选的固化工艺。高低温环境冲击和低剂量的粒子辐照后胶黏剂固化反应更加充分,其芯片剪切强度提高,而大剂量辐照致使高分子降解现象明显,造成了胶接强度的降低。经环境试验后,MD-130胶黏剂仍具有良好的力学性能,满足设计使用要求。     

WC/C复合涂层海水环境的耐蚀性与摩擦性能

采用非平衡磁控溅射技术在304L不锈钢和单晶硅基底上沉积WC/C多层复合涂层,利用扫描电镜、Raman光谱仪、X射线衍射仪等研究WC/C复合涂层的微观结构,采用纳米压痕仪、划痕测试系统测试涂层的力学性能,利用电化学测试系统和摩擦磨损试验机分别研究涂层在人工配置的海水环境的耐蚀性能和摩擦性能。结果表明:WC/C复合涂层内含有较多类石墨sp2键结构,存在WC1-x相并镶嵌在非晶碳基质中。较之于304L不锈钢基底,WC/C复合涂层在海水环境中表现出更好的耐蚀性与更优异的摩擦适应性。     

陶瓷隔热瓦的缺陷修补

分别采用了MgO、YSZ和Al₂O₃三种陶瓷粉体和一种含隔热瓦本体成分的粉料对陶瓷隔热瓦缺陷进行修补。研究了修补前后材料的微观形貌、力学及隔热性能。结果表明：采用含隔热瓦本体组成的粉料对陶瓷隔热瓦进行修补,修补部位与本体部位相容性好,且微观形貌相似,仍保持纤维搭接的多孔空间网络结构;修补后试样密度0.24 g/cm³、室温热导率0.044 W/（m·K）、压缩强度0.58 MPa;1 200℃、30 min热处理后,修补部位与本体部位结合性好,未出现裂纹、凹陷等缺陷,是有效的缺陷修补方法。     

铣槽结构液体火箭发动机推力室壳体热应力分析

介绍了液体火箭发动机推力室铣槽结构热应力的数值分析方法,通过建立液体火箭发动机推力室的流场燃烧和导热理论模型,运用有限体积法考虑液膜冷却计算出发动机工作时的燃气、燃烧室壳体和冷却工质的温度场,将得出的结果作为壳体热应力计算模型的边界条件进行热应力场有限元分析。内、外壁温度的计算数据与实验结果基本相符。     

ZrO2陶瓷热障涂层显微结构及隔热性能研究

用电子束物理气相沉积法(EB-PVD)在DZ125高温合金上制备Y2O3部分稳定化的ZrO2(YSZ)陶瓷热障涂层,并用扫描电镜(SEM)观察涂层显微结构.采用激光脉冲法对EB-PVD热障涂层的热扩散系数进行测试.为防止热扩散系数测试时激光穿透ZrO2陶瓷层,在试样表面制备不同材料的遮挡层.结果表明,EB-PVD热障涂层呈明显的柱状晶结构,柱状晶垂直于涂层/基体界面.基体的热扩散系数随温度的升高而急剧增加,陶瓷热障涂层的热扩散系数随温度的升高呈下降趋势,但变化幅度不大.室温下陶瓷层的热扩散系数小于基体的1/3,1200℃时约为基体的1/67.试样的激光遮挡层很好解决了激光脉冲法测试涂层热扩散系数时的不稳定性和激光穿透问题.在满足遮挡要求的条件下,遮挡层材料种类对热扩散系数测试无明显影响.     

接触热阻对固体火箭发动机烤燃时间的影响

应用有限元法对某模拟固体火箭发动机的热烤试验过程进行了数值模拟研究,对比分析了在相同的外界条件下,考虑接触热阻与不考虑接触热阻时推进剂的起始燃烧时间。结果表明,考虑接触热阻的影响对于准确预测发动机的烤燃时间有重要的影响。     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.