Study of GNSS-measured ionospheric total electron content variations generated by powerful HF-heating

The purpose of this work is to report the experimental evidences for the influence of perturbations in the electron density in the dayside mid-latitude ionosphere, that are caused by high-frequency heating of the F2 layer, on the GNSS signals. The experiments were carried out at the Sura heater (Radio Physical Research Institute, N. Novgorod). During the sessions of ionospheric heating with different time modulations of the radiated power the rays linking the navigational satellites with the ground receiver intersected the heated region. Variations in the total electron content (TEC) were studied; these variations are proportional to the reduced phases of navigational signals. It is shown that with the square-wave modulation of the radiated power (with periods of 1, 6, 10 and 15 min), perturbations with periods of the main modulation of heating and its harmonics appear in the spectrum of TEC variations. Examples are presented of identification of the heating-induced variations in TEC, including determination of the amplitudes and time characteristics of these variations.     

浅议信息时代高校校报的发展

在以网络为代表的新媒体无孔不入的今天,传统的报纸面临着巨大的压力,同样新媒体对高校校报的冲击无疑也是巨大的。如何在竞争激烈的新媒体时代继续引领校园舆论,是所有高校校报人所引以深思的问题。列举了信息时代以网络为核心的新媒体对高校校报的冲击,特别是在读者获取信息的方式、读者阅读兴趣、读者阅读习惯等方面的巨大影响;分析了高校校报和网络媒体在内容、形式等方面各自的长处和特点,并初步提出了高校校报机构调整和加深内涵建设等应对措施。     

Experimental investigation on silica dust lofting due to charging within micro-cavities and surface electric field in the vacuum chamber

The charged dust particles can be mobilized electrostatically by the repulsion between the adjacent grains and the surface electric field due to the incoming electron current and the charge accumulation within the micro-cavities. In this study, the experimental results of the initial vertical launching velocities and the maximum dust heights are compared with the estimated values for the lofted spherical dust grains by the patch surface charging equations. Silica particles with the sizes between <6 and 45?µm in radius are loaded on a graphite plate, and they are exposed to the electron beam with 450?eV energy under 4?×?10^?3?Pa vacuum chamber pressure. During the first set of the experiments, the dust samples are tested without an initial compression process and an additional horizontal electric field. Second, the dust samples are compressed by two different weights in order to increase the packing density under approximately 780.7?Pa and 3780?Pa. Finally, the dust grains are placed between the two parallel aluminum plates to apply approximately 2000?V/m and 4800?V/m horizontal electric field. A high-speed camera is used to record the transportation of the dust grains together with a microscopic telescope, and the results point out that the patch surface dust-charging model estimations are in agreement with the first experiments. On the other hand, the dust particles from the compressed samples are lofted with higher velocities than the estimations, and the number of the dust lofting observations decreases significantly, which demonstrates the importance of the micro-cavities and the increased charging requirement to overcome the contact forces. When the horizontal electric field is present, the initial vertical launching velocities are measured to be lower than the other experiments, which can be attributed to the decreased charging requirement for the dust lofting as a result of inter-particle collisions and rolling motion. According to the experimental results, the electrostatic dust transportation can be controlled not only by the ambient plasma and the solar irradiation on the airless planetary bodies, but also by the surface properties such as the contact surfaces between the dust grains, the number of the micro-cavities related to the packing density, and the presence of the horizontal electric field contributing to the external forces by other particle motions.     

气动钣金快速成形机的研制

针对电动钣金成形机制造成本高、效率低、易产生死点的问题,提出一种采用气液增力装置代替液压传动系统的气动钣金成形机设计方案。气液增力装置采用精密气压转换阀控制,实现行程平稳控制和加工成形过程平稳加载,显著提高了生产效率;配套研制的多种无齿收缩成形模具,可加工不同形状钣金件并获得更好的表面质量。该技术在钣金快速成形方面的研究处于国内领先水平,已获得3项国家专利。     

李清照《醉花阴》赏析

李清照是北宋婉约派词人的代表作家,她的词刻画细腻,微妙的心理活动,表达丰富多样的感情体验,塑造鲜明、生动的艺术形象。《醉花阴》通过白日独坐,对花浅酌的场景,人花比瘦,刻画词人思念之情。     

汉乐府《陌上桑》罗敷形象再解读

《陌上桑》是一篇被世人广为传诵的汉乐府佳作,作品塑造一个鲜活的充满生命活力的女子形象———罗敷,她美丽、健康、自信、阳光、勇敢、自尊,一改传统诗文中女性的哀怨、病弱、卑怯、凄苦之态,成为文学史中一个光彩照人的独特形象,具有特殊的意义。     

廊坊市新农村建设中的生态环境存在的问题及对策

和全国其他地方一样,廊坊市在大力推进社会主义新农村建设的过程中,也面临着农村生态环境恶化的困境。为了实现农业生产发展和农村生态环境保护之间的平衡,政府应当加大公共财政支出向农村地区倾斜的力度,坚持规划先行、服务跟进的原则,切实改善人居环境,强化农村生态环境保护法制的实施,把新农村建设成为生态良好的新农村。     

基于CCSDS标准的航天器上行遥控链路 协议体系与可靠性技术

针对航天测控领域中上行遥控业务的协议体系选择与可靠性设计问题,在对我国现行国军标技术指标要求与现有航天测控系统天地基遥控技术特点进行归纳梳理的基础上,基于空间段信息传输无线链路特点与CCSDS(Consultative Committee for Space Data Systems,空间数据系统咨询委员会)标准规范,研究给出了适用于我国航天测控任务的空间段遥控协议体系与可靠性措施,利用梳理统计方法对上行遥控体制进行了数学建模分析,并与CCSDS给出的应用算例进行了对比分析.分析结果表明,所涉及的上行遥控体制与CCSDS标准规范的工作效能基本相当,能够满足我国航天任务上行遥控任务使用需求.     

磁强计数据辨识卫星自旋状态

针对近地低轨三轴稳定卫星在轨管理后期,除磁强计外其他姿态敏感器都无效情况下的姿态异常问题,分析了三轴稳定卫星失去姿态基准后,星体自旋状态下三轴磁强计测量数据的特点,提出了使用磁强计测量数据的矢量信息,以找到能够获取卫星状态的方法,从而建立了磁强计测量矢量与卫星自旋轴的几何关系,给出了处于自旋状态下的卫星自旋轴确定方法。通过此种辨识方法,获得了某气象卫星姿态异常翻转状态下的自旋矢量方向和自旋角速度,从而证明了该辨识方法快速、有效,可以作为姿态异常卫星自旋状态的辨识手段,为恢复卫星姿态提供了重要信息,具有一定的工程应用价值。