Forming Characteristics of Al-alloy Large-diameter Thin-walled Tubes in NC-bending Under Axial Compressive Loads

Tube thinning control without wrinkling occurring is a key problem urgently to be solved for improving the forming qualities in numerical control (NC) bending processes of large-diameter Al-alloy thin-walled tubes (AATTs). It may be a way solving this problem to exert axial compression loads (ACL) on the tube end in the bending. Thus, this article establishes a three-dimensional (3D) elastic-plastic explicit finite element (FE) model for the bending under ACL and has its reliability verified. Through a multi-index orthogonal experiment design, a combination of process parameters, each expressed by a proper range, for this FE model is derived to overcome the compression instability on tube ends. By combining the FE model with a wrinkling energy prediction model, an in-depth study is conducted on the forming characteristics of large-diameter AATTs with small bending radii and it can be concluded that (1) The larger the tube diameters and the smaller the bending radii, the larger the induced tangent tension stress zones on tube intrados, by which the tube maximum tangent compression stress zones will be partitioned in the bending processes; thus, the smaller the ACL roles in decreasing thinning degrees and the larger the compression instability possibilities on tube ends. (2) The tube wrinkling possibilities under ACL are larger than without ACL acting in the earlier forming periods, and smaller in the later ones. (3) For the tubes with a size factor less than 80, the ACL roles in decreasing thinning degrees are stronger than in increasing wrinkling possibilities.     

红外热像仪防辐射罩冷挤压成形技术研究

星载红外热像仪防辐射罩为多台阶锥筒形薄壁零件,材料为较软的铅质材料,加工难度较大。为了解决加工成形的难题,对各种加工方法(切削、拉伸、旋压、冷挤压)进行了分析、对比和试验验证,最终采用冷挤压技术解决了防辐射罩加工成形的难题,而且加工成形的防辐射罩满足各项技术要求,加工成品率很高,材料消耗小,成本低,效果良好。     

板料机械性能指标与压制成形性能间的关系

本文通过一定的试验数据，对板料机械性能指标与压制成形性能间的关系进行了定性的分析。     

基于载波相位的多通道相位一致性测量方法CSCD

对于卫星导航系统,由导航天线进行波束合成的多路并行导航信号需要具有严格的相位一致性,本文给出基于专用地检设备的多通道相位一致性测量方法。该地检设备采用载波相位辅助伪码测距技术,通过载波相位和伪码相位的联合解算,实现了伪码相位对载波相位解整周期模糊,最终测距精度达到1ps。采用该测试方法对系统进行配相,实现了各通道无周期模糊的相位一致性。     

Development of microstructural inhomogeneity in multi-pass flow forming of TA15 alloy cylindrical parts

Revealing the development of microstructural inhomogeneity in the multi-pass flow forming of titanium alloy components is of great significance to the microstructure control and property tailoring. To this end, the microstructural inhomogeneity of TA15 alloy spun cylindrical parts was analyzed based on the deformation history. The results indicate that the material underwent significant compressive strain in the normal direction (ND), tension strain in the rolling and circumferential directions (RD and CD), while tension strain in the CD is slightly small due to the limited material flow in this direction. These strain characteristics make the microstructure, especially the primary α (α_p), present different morphologies in the different planes of the part. Meanwhile, the combined effects of inhomogeneous deformation and temperature distribution in the ND also cause the inhomogeneity of microstructure morphology and parameters in this direction. Quantitative analyses show that with the forming pass increasing, the aspect ratio of α_p increases most in the normal-rolling plane, then in the normal-circumferential plane and least in the circumferential-rolling plane, whereas α_p content decreases in an opposite trend. Along the ND, the aspect ratio and content of α_p is relatively high in the outer and inner surface areas but lowest in the central area, and these inhomogeneous characteristics can be gradually diminished with the forming pass increasing. Furthermore, the variation of hardness inhomogeneity factor indicates that a four-pass forming with the total reduction ratio of 63% could obtain a homogenous microstructure along the ND of the TA15 alloy spun cylindrical part.     

提高航空发动机性能的弯扭导向器技术

给出了采用弯扭导向器提高发动机性能的设计原则：在全三维弯扭设计时，必须在保证涡轮前总温、总压和燃气流量的前提下，合理调整尾喷管面积，提高涡轮后背压，保证在设计转速下涡轮输出功与原型涡轮级相同，从而保证了压气机的设计点和喘振裕度，同时提高了发动机推力、降低油耗。     

基于单向拉伸的防锈铝合金温热力学性能研究

通过不同温度及应变速率下的单向拉伸试验,获得了5A06-O防锈铝合金板材关键力学性能参数的变化规律。结果表明,在一定的应变速率下,5A06铝合金的流动应力及抗拉强度随着温度的升高而降低,断后延伸率随着温度的升高而显著的提高。当温度处在20～150℃范围内,均匀延伸率随着温度的升高而升高,而在150℃～300℃范围内,随着温度的升高而降低。另外,基于Fields&Backofen本构方程,对5A06铝合金在不同温度状态下的强化规律进行了分析和探讨,结果表明,随着温度的逐渐升高,应变强化指数不断减小,应变速率敏感系数则显著增大,应变速率强化作用明显增强。     

静电拉伸空间薄膜反射镜面形控制机理研究

薄膜反射镜将解决反射镜孔径与重量相互制约的问题. 采用静电拉伸法控制薄膜反射镜面形, 具有结构简单、反射镜面形易于控制等优点, 其原理为利用静电场上库仑力作用使薄膜产生面形变化, 生成所需的光学曲面. 由于薄膜变形力学, 以及静电场理论的复杂性, 目前薄膜成形及其面形控制在理论分析上仍未有定量的结果. 本文主要以单电极静电场中的薄膜反射镜面形为考察因素, 通过数值计算的方法得到薄膜反射镜上的静电力分布, 运用有限元分析获得该分布下的反射镜面形, 并将其与理想面形进行比较. 提出采用多电极闭环控制可获得更高的控制精度, 对静电拉伸薄膜的研究具有一定的指导意义.      

7B04铝合金蠕变过程中析出相的影响因素

进行了7B04-T7451铝合金在不同蠕变温度、不同应力水平下的多组蠕变实验,根据蠕变率的变化,得到了合理的蠕变温度为150℃;在此温度下进行了不同应力水平和时效时间下的多组蠕变实验,分析了加工条件对微观组织和力学性能的影响.结果表明,高的应力水平能加速合金强化相的析出和转变,同时增大位错的流动能力,因此,随着蠕变时间的增加,材料的屈服强度呈先上升后加速下降的趋势.