An extended chirp scaling algorithm for spaceborne sliding spotlight synthetic aperture radar imaging

A system impulse response with low sidelobes is critical in synthetic aperture radar（SAR） images because sidelobes contribute to noise and interfere with nearby scatterers. However,the conventional tricks of sidelobe suppression are unable to be exactly applied to the case of spaceborne sliding spotlight SAR due to great azimuth shifts in both time and frequency domains. In this paper, an extended chirp scaling algorithm is presented for spaceborne sliding spotlight SAR data imaging. The proposed algorithm firstly uses the spectral analysis（SPECAN） technique to avoid the azimuth spectrum folding effect and then employs the chirp scaling（CS） algorithm to achieve data focusing, i.e., the so-called two-step approach. To suppress the sidelobe level, an efficient strategy for the azimuth spectral weighting which only involves matrix multiplications and short fast Fourier transformations（FFTs） is proposed, which is a post-process executed on the focused SAR image and particularly simple to be implemented. The SAR image processed by the proposed extended CS algorithm is very precise and perfectly phase-preserving. In the end, computer simulation results verify the analysis and confirm the validity of the proposed algorithm.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

含噪信号经验模式分解虚假分量识别方法

针对含噪信号Hilbert-Huang变换存在虚假分量,提出改进的奇异值分解(SVD)方法进行降噪,改进包含两个部分:一是利用重构相空间代替传统矩阵如Hankel矩阵,以去掉信号冗余,再者提出奇异值能量熵分量差分法,更易于定出重构奇异值阶次;二是提出了频谱比值法对虚假分量进行辨识,更有效辨识出虚假分量.首先利用经验模式分解(EMD)得到本征模式分量(IMF),识别并剔除趋势项,重构信号,然后进行SVD,重构降噪后的信号,消除虚假分量,最后进行时频分析.联合方法应用于含噪仿真信号,信噪比(signal noise ratio,SNR)提高了5.5%,虚假分量辨识率提高至100%,用于双跨转子故障振动信号,得到正确的时频结果,表明了所提方法识别含噪信号虚假分量的有效性.     

肋角度对气膜冷却特性的影响

在光滑二次流通道的基础上,分析对比了两种带肋通道(135°肋和45°肋)对气膜冷却特性的影响.采用瞬态液晶测试技术获得了气膜孔下游表面传热系数比与气膜冷却效率分布.使用Fluent软件RANS数值方法对相应结构进行了数值模拟,并使用了realizable k-ε湍流模型.光滑二次流通道模型中,气膜孔内流线呈螺旋状分布,导致较大的孔内速度分离与流动损失.冷气射流分成两部分,其中一股形成一对偏斜的对转涡.135°肋结构中,二次流通道上部分的旋转涡为顺时针方向,使得气流易于流入气膜孔,气膜孔内流线呈直线分布.45°肋结构中,二次流通道上部分旋转涡为逆时针方向,增强了气膜孔内旋转涡.45°肋结构中冷气流入气膜孔之后的流动结构与光滑二次流通道结构相似.135°肋结构气膜冷却效率最大而表面传热系数比最低.     

飞机下滑波束导引系统设计及仿真

下滑波束导引系统是飞机在自动着陆时所采用的一种重要无线电波束导引系统。首先,简要阐述了下滑波束导引系统的基本工作原理;然后,对导引系统的运动学环节及下滑耦合器进行分析,对飞机下滑波束导引系统结构进行设计;最后,在MATLAB平台下,对所设计的下滑波束导引系统进行大量仿真研究。仿真结果显示。所设计的下滑波束导引系统结构是合理的,其控制系统是稳定的,且其稳态性能也得到改善。     

浅析运输类飞机经济舱头排旅客座椅头部损伤判据的影响因素

介绍了头部损伤判据HIC的概念、适航要求及影响运输类飞机客舱头排旅客座椅HIC的相关参数;叙述了旅客座椅头排距、头部撞击壁板的刚度、安全带织带伸长率、乘坐摩擦系数等参数的影响和重要程度;对如何设计符合HIC要求的经济舱头排旅客座椅和壁板提出了建议。     

民用飞机综合模块化航电系统分区和资源分配的研究

对比航电传统系统架构,分析了综合模块化航电系统(Integrated Modular Avionics,简称IMA)架构的优点;针对IMA系统功能的高集成度带来的资源分配难度和安全性要求,提出了IMA系统分区和资源分配策略,并给出了具体方法,对民用飞机IMA系统设计具有一定的指导意义和实用价值。     

基于A320飞机横航向控制律架构的LQ设计

空客A320飞机横航向控制律采用特征结构配置方法计算闭环增益,实现了期望特征值的配置及横航向关键参数之间的解耦。基于A320横航向控制律架构,提出使用线性二次型(Linear Quadratic,简称LQ)方法,对闭环增益进行重新设计。首先根据期望的特征值引入关键参数的频域整形环节,而后通过调整二次型性能指标加权矩阵实现期望特征值的逼近及关键参数之间的解耦,并求得闭环反馈增益,最后在特征结构、稳定裕度和横航向解耦效果方面与空客设计结果作了对比分析。仿真结果表明,LQ设计可获得与特征结构配置设计相近的结果,即得到接近期望值的特征值,并实现关键变量的解耦,同时保证了闭环稳定裕度。     

微小推力下小卫星的轨道递推与推力标定

针对采用微小推力进行轨道机动的小卫星,考虑复杂摄动力的基础设计了一种高精度轨道外推和推力在轨标定算法.首先,建立了考虑地球复杂摄动力和微小推力的小卫星轨道动力学模型;然后基于动力学模型,利用变步长龙格库塔算法,设计了对微小推力小卫星进行高精度轨道外推的方法.随后通过无迹卡尔曼滤波器(UKF),设计在轨标定算法,对存在误...     

CCD信号采样位置选取方法的研究

针对CCD输出信号中的复位噪声,文章介绍了处理复位噪声较为常用的方法--相关双采样技术,并对相关双采样技术中采样位置选取的方法进行分析和研究,最后进行了实验验证.结果表明:用文中方法选取的采样位置进行相关双采样,可以较好的减小CCD输出信号中复位噪声的影响,提高信噪比.