Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

图形背景理论模式下英语强调结构的教学认知

在英语中,说话人要重点突出的部分叫做强调.强调结构一直是学生学习英语的重点和难点。传统的教学方法存在诸多弊端,学生不会综合运用,不懂融会贯通。从新的视角对英语强调结构的教学进行认知势在必行。认知语言学中图形-背景理论为重新感知和理解强调结构提供了理据,进行形象具体化教学,有效提高学习效果。     

基于层次评估理论的弹道导弹末段突防制导律研究

针对弹道导弹末段突防问题,应用层次性能评估体系,对弹道导弹末段典型突防制导律进行对比分析.并通过对弹道导弹制导精度、弹道导弹最大过载、弹道飞行时间和反导导弹脱靶量以及它们的均值、均方差的重要性和需求性分析,合理设置评估体系的指标及其权值,应用随机仿真分析方法,对比仿真经典比例导引、修正比例导引和变结构比例导引三种突防制导律的性能.仿真结果证明,层次评估理论可以用于弹道导弹末段突防制导律的评估及优选.     

蜂窝式轴心通风器油气分离性能计算

为对航空发动机蜂窝式轴心通风器油气分离效率进行研究,建立考虑油气双向耦合的流场计算方法及油滴/壁面相互作用模型,在验证通风阻力及油气分离效率可靠性的基础上,对不同转速、通风流量和环境温度下蜂窝式轴心通风器的油气分离效果进行计算和分析.结果表明:转速的增加会使油气分离效率得到提升,而通风流量和环境温度的增加则导致油气分离效率的降低.蜂窝孔结构的加入对通风阻力影响不大,却对通风器的滑油分离过程起主要作用,计算表明其对滑油分离贡献率在80%以上.      

Analyses toward factors influencing sealing clearance of a metal rubber seal and derivation of a calculation formula

Sealing clearance is a key factor for a metal rubber seal’s sealability. The expansion coef-ficient and expansion deformation in the radial direction of metal rubber have been obtained through a thermal expansion experiment of metal rubber. The influence of the elastic modulus to the sealing clearance has been analyzed theoretically. By combining the temperature and elasticity factors of metal rubber with the elastic mechanics theory, the calculation formula of the sealing clearance has been derived, and the values of the sealing clearance and the leakage rate in certain working conditions have been calculated. Experimental results are consistent with calculation results in a high degree. The calculation formula of the sealing clearance can explain the influences of the temperature and elastic modulus factors of metal rubber on the sealing clearance. It can pro-vide guidance for the study of sealing mechanism of metal rubber seals.     

基于格子Boltzmann方法表面形貌对微通道对流换热的影响

为推动微通道冷却技术在航空发动机中的应用,进一步提高航空发动机性能,本文通过扫描电子显微镜、粗糙度扫描仪等多方式扫描得到实际加工物体表面形貌,结合分形理论进行处理,得到真实、光滑、分形插值、康托尔集四类圆形截面管模型,管径100μm~400μm;采用格子Boltzmann方法进行数值模拟,首先通过与文献中实验结果的对比,验证了此方法的正确性,然后对空气在这四类圆形截面微通道中的对流换热特性进行了数值模拟,计算雷诺数Re范围80~640;结果发现：表面形貌是微通道中对流换热不可忽略的因素,相对粗糙度越大越有利于换热,真实扫描管的换热性能要比相同条件下光滑管高2.22%;分形理论可用于微通道表面形貌的构建,在相同迭代次数下,分形插值模型与真实扫描形貌换热性能相差0.03%,而康托尔集模型与真实扫描形貌换热性能相差1.88%,分形插值模型较康托尔集模型更能真实地反映实际形貌;微通道中,随着雷诺数的增加Nu将不再是常数,而是有增加的趋势。     

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

双脉冲固体火箭发动机隔舱打开与破片运动过程模拟

相比传统固体火箭发动机,具有能量管理特性的双脉冲固体火箭发动机结构更为复杂,为了提高其工作可靠性,针对核心部件金属隔舱的破片运动过程开展了数值仿真与试验研究。首先基于LS-DYNA软件,分析中引入监测函数、逻辑开关函数和加载驱动函数,模拟燃气流对破片的连续作用力,计算得到了在不同时刻破片的空间分布规律、撞击点位置及发动机内部损伤情况,保证了破片运动过程的高保真还原。其次,为了验证仿真结果的准确性,进行了模拟二脉冲初始工况的热流试验,发现破片撞击位置及损伤程度的仿真结果与试验数据一致性较高,其中撞击位置的预示误差小于9%,试验结果充分验证了有限元模型的准确性。由此,建立了适用于双脉冲固体火箭发动机金属隔舱破片运动过程的分析模型,实现了破片撞击位置及损伤程度的高精度预示。     

基于气压高度辅助的机载自主完好性监测算法

卫星接收机自主完好性监测是指根据用户接收机的多余观测值监测用户定位结果的完好性,其目的是在导航过程中检测出发生故障的卫星,并保障导航定位精度。针对卫星接收机自主完好性监测算法可用性不足的问题,结合机载实际导航系统配置,提出了一种基于气压高度表辅助的机载自主完好性监测算法。综合利用卫星导航系统及气压高度表观测信息,建立联合系统的观测模型,推导了基于多解分离的完好性监测及保护级别计算方法。仿真结果表明,相比于传统的接收机自主完好性监测算法,该算法在可见星为5颗时仍能识别故障卫星。该算法具有更好的故障检测能力及可用性,能有效提高卫星导航系统的完好性监测性能,从而保证卫星导航系统的精度和可靠性。