Potential of IRNSS/NavIC L5 signals for ionospheric studies

Indian Space Research Organization (ISRO) has developed an indigenous system named Indian Regional Navigation Satellite System (IRNSS) or NavIC (Navigation with Indian Constellation), that consists of 7 satellites and transmits navigation signal in L and S bands. ISRO, for validation of the system, has installed many IGS (IRNSS/GPS/SBAS) receivers scattered over the Indian region. Using preliminary data from two geographically widely separated stations over India, this paper presents the results on studies on parameters of IRNSS signal quality and discusses how these parameters may be used to study the ionospheric behavior over the Indian region. The results show the importance and advantages of using IRNSS data for such studies.     

飞机漂浮性分析的ACN计算方法

给出了刚性和柔性两类铺砌道面下，由飞机所需的道面厚度计算ACN值的方法。对于刚性道面，给出了不同刚度的地基下计算ACN的公式和计算系数。经三种具有代表性的机型进行验算，验证了方法的准确性。对大量计算数据的分析表明，地基类型和地基强度对ACN计算方法有很大影响，若要准确计算飞机的ACN值，可对ACN计算系数进行插值扩展，得到计算系数关于地基刚度的多项式。应用方法对某型飞机的漂浮性进行评估，结果表明有一定的工程实际意义。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

典型工况下低排放燃烧室的压力振荡特性

为了研究低排放燃烧室在典型工况下的压力振荡特性,针对模型燃烧室进行了燃烧自激振荡特性试验.在试验中测量了采用贫油预混预蒸发(LPP)燃烧技术的低排放燃烧室在典型工况下的压力振荡频率和幅值,在燃烧室进口压力为1.10～2.77MPa、燃烧室进口温度为656～845 K、燃烧室压降为3.41％～4.35％范围内,分析了燃油粒径变化对振荡特性的影响.分析结果表明:局部当量比脉动是引发燃烧不稳定的因素之一.通过计算燃油二次雾化状态下的液滴最大粒径,发现燃油液滴粒径的变化对主燃级出口处的局部当量比脉动有直接影响,从而引起燃烧室压力振荡幅值和频率的变化.     

叶片反扭对跨声速大涵道比风扇性能的影响

使用基于流固耦合算法的叶片反扭程序,考虑了非定常气动力对叶片变形的非线性作用,研究了叶片反扭对跨声速大涵道比风扇性能的影响.以冷态叶型为起点,先计算离心力作用下的叶片变形,在此基础上使用流固耦合程序获得非定常气动力作用下的变形.考察了3个转速下叶片的动态变形对大涵道比风扇气动性能的影响.结果表明:在跨声速工况下,叶片表面激波位置的变化对叶片反扭角有很大作用,在考察的转速范围内,堵塞点使用设计叶型计算的流量大于动态叶型下的流量,数值达7%,将导致发动机起飞推力小于预测值.结果表明在大涵道比风扇设计阶段,预测气动性能使用准确叶型的重要性.      

翼吊发动机安装结构等效建模及其隔振设计

为了研究翼吊发动机安装结构隔振特性并优化其隔振器设计,建立了发动机安装节-吊架-机翼结构理论分析及有限元模型.利用有限元方法进行了模态验证并分析了安装结构的隔振特性.进行发动机3种典型工况下的结构动响应分析确定了振动传递的主路径.基于振动传递路径法研究了隔振器参数和安装位置对安装系统隔振性能的影响规律.结果表明:振动载荷经安装结构后低压转子转频和高压转子转频峰值响应分别降低22.03%和14.65%.低压转子转频振动传递主路径为发动机-前安装节-吊架-机翼,高压转子转频为发动机-后安装节-上连杆-机翼.通过合理设置隔振器位置可以使安装系统隔振率达到50.41%,隔振器的频率比为5和阻尼比为0.25时安装系统隔振率可达70.67%.为了优化整个发动机安装系统的隔振效果,设计隔振器时必须选取合适的安装位置和参数.      

预燃式等离子体射流点火器工作特性实验研究

为解决发动机点火包线小于飞行包线的实际问题,提供等离子体点火技术在航空发动机中的工程应用新思路,论文设计了一种预燃式等离子体射流点火器,实验研究了放电特性和射流特性。结果表明,预燃式等离子体射流点火器与空气等离子体射流点火器相比,在提升射流能量降低电源功率方面有着较大的优势,电流相同时通入甲烷在较大流量时可减小驱动电源功率,总流量为44L/min时,减幅可达14.99%;同时预燃式等离子体射流较空气等离子体射流稳定,且射流长度增加,扩大了点火面积,有利于点火。     

“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

两次载荷分流齿轮传动构型的静力学均载特性

为改善面齿轮-圆柱齿轮两次载荷分流传动构型的均载特性,考虑齿轮的中心偏移、轴与轴承的承载变形等因素,依据构型的变形协调条件和力矩平衡方程,建立了传动构型的静力学模型,研究了轴的扭转和支撑刚度对均载特性的影响。结果表明:输入轴扭转刚度对均载特性几乎没有影响;分扭轴扭转刚度取合适的比值,则面齿轮分扭传动级可获得较好的均载特性,但圆柱齿轮分扭传动的均载特性几乎无变化;减小双联齿轮轴扭转刚度或增加双联轴支撑刚度可提高该构型的均载特性。因此,为提高该传动构型的均载特性,轴的扭转刚度和支撑刚度需采用参数匹配的设计方法。     

Experimental investigations of the spray structure and interactions between sectors of a double-swirl low-emission combustor

In this paper, the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry (PIV) and Planar Laser Induced Fluorescence (PLIF) technologies in an optical three-sector combustor test rig. Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained. The results illustrate that the swirl intensity has great effect on the flow field and spray structure. The spray cone angle is bigger when the swirl number is 0.7, 0.9 than that when the swirl number is 0.5. The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5. The fuel concentration in the center area of the center plane of side sector (Plane 5) is larger than that of the center plane of middle sector (Plane 1). The spray cone angle in Plane 5 is larger than that in Plane 1. The width of spray cone becomes larger with the increase of Fuel–Air Ratio (FAR), whereas the spray cone angle under different fuel–air ratios are absolutely the same. The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.