采用逐次正交化法的最优分布式Kalman滤波器

为解决大系统中应用整体式Kalman滤波遇到的非实时性难题,本文提出一种能保持最优的分布式Kalman滤波计算方法——逐次正交化法。这是一种适合多微机并行计算的最优算法,确保滤波的“实时性”,优于一般次优分布式Kalman滤波器。     

羊毛精纺织物服用性能优选的多属性模糊决策

本文应用多属性目标决策的方法,评判不同规格毛织面料的"满意度",客观地提供一个重要的优选辅助依据。     

面向代理模型的机翼变形计算方法

按照机翼结构设计的原则,对内部结构还未确定的机翼提出了一种通用的变形计算方法。机翼的平面形状可看作由多个梯形组成,机翼弯曲变形为三次函数,扭转变形为一次函数。只要给定翼梢挠度与扭转角,即可计算机翼变形情况下的几何模型,使代理模型能够预测变形后机翼的气动载荷分布。文中给出了两个实际机翼的算例。算例结果表明,本文模型预测的变形与实际结构有限元分析给出的变形吻合较好。     

基于响应面法的超燃冲压发动机进气道多目标优化

基于响应面法进行了二维混合压缩超燃冲压发动机进气道的多目标优化研究.采用均匀试验设计确定试验方案,运用计算流体动力学求解进气道的性能.根据分析结果构造了响应面近似模型,该模型采用了完全二阶多项式模型.通过响应面近似模型的优化,实现了超燃冲压发动机进气道优化,得到了Pareto最优集.结果表明,采用均匀试验设计和响应面法可以大大减小数值模拟的计算量,提高优化效率.     

双层多目标规划若干问题的研究

研究了下层决策者无关联的双层多目标规划问题，在不同偏好意义下，给出了各自解的定义，讨论了线性双层多目标规划问题。     

结构优化中的混合变量应力约束近似方法

提出一种处理结构优化应力约束的新近似方法，以往一般直接对应力约束按设计变量近似，本文用近似内力间接近似应力约束以得到更高的近似质量，根据对内力和设计变量关系分析，提出了内力按混合变量一阶泰勒展开的高捏近似方法。近似优化问题用约束变尺度法求解，最后按出了几个典型例题。结果表明该方法简单，有效，可靠。     

基于连续覆盖特性分析的星座设计

研究了需要对地面目标进行连续覆盖的星座的设计问题．首先推导了对覆盖性能有重要影响的星间覆盖间隔时间和轨道面覆盖间隔时间的计算公式，通过算例针对不同配置的星座进行了计算，使用工程仿真软件STK验证了分析结果．通过理论分析、算例计算以及工程仿真为该类型星座设计提供了理论指导。     

基于参数化模型和遗传算法的复合材料加筋壁板结构选型优化研究

针对复合材料加筋壁板的结构优化选型问题,采用辅助层压板和添加极小弹性模量材料的复合材料加筋壁板有限元建模方法,应用PATRAN/NASTRAN的参数化建模功能和遗传算法相结合的复合材料加筋壁板的优化方法,对5种复合材料结构形式进行了从2000N/mm到6000N/mm压缩载荷下的结构优化分析。结果表明,当载荷小于4500N/mm时,最有效的加筋壁板结构型式为J型;当压缩载荷大于4500N/mm时,最有效的加筋壁板结构型式为I型。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.