PIC检测器解析表达式的偏差修正

由于传统PIC(Parallel Interference Canceller,并行干扰消除)检测器性能分析公式存在偏差,导致与仿真结果有一定的差异,不能准确反映系统性能。在对传统PIC检测器性能表达式和推导过程存在的偏差进行分析的基础上,通过公式推导,得到更为精确的PIC检测器任一级的误码率性能解析表达式。通过数值计算,偏差修正后的解析表达式对误码率估计的准确度比修正前提高了1个数量级,与仿真结果更为接近,并且干扰消除的级数越多效果越好。研究结果表明,修正后的PIC解析表达式是有效的。     

BDS-3 PPP模糊度固定实现及精度评估

精密单点定位(PPP)模糊度固定(AR)能够显著提升精密定位的收敛速度和精度。通过在BDS-2和BDS-3之间添加系统间偏差的方法实现BDS-3的模糊度固定,并基于全球MGEX测站静态、仿动态数据和车载实验数据全面评估了BDS-3模糊度固定的效果。结果表明,相对于浮点解,BDS-3 PPP模糊度固定能够显著提升PPP的精度,在东北天3个方向上静态解算精度提升依次为37.4%、26.2%和20.1%;仿动态解算精度提升依次为38.3%、27.2%和11.1%;车载动态实验BDS-3模糊度固定精度在三维方向上综合提升为40.4%。此外,模糊度固定后,以浮点解稳定后的两倍定位精度为基准,在东北天方向上,静态定位时间提升程度依次为63.5%、64.0%和40.3%;仿动态定位时间提升程度依次为58.7%、56.8%和25.4%;车载实验在三维方向的收敛时间为30.0 min。以上结果证明了所提方法的有效性及BDS-3模糊度固定的性能提升。     

一种弹性胶粘剂在石英加速度计中的应用

针对石英加速度计偏值问题,提出了摆片组粘接胶粘剂的选用原则,并应用有限元软件进行了仿真研究.分析结果表明,固化后弹性模量小的胶粘剂粘接面产生的应力较小,有利于提高石英加速度计偏值的稳定性.进一步对选用的弹性胶粘剂进行了强度检测,测试结果表明石英加速度计的偏值稳定性得到了明显改善.     

Fast calibration of between-receiver GPS/Galileo/BDS differential phase bias with millimeter accuracy based on short baseline mode

The differential code and phase biases induced by the receiver hardware (including receiver, antenna, firmware, etc.) of the Global Navigation Satellite System (GNSS) have significant effects on precise timing and ionosphere sensing, thus deserve careful treatment. In this contribution, we propose an approach to fast fix the single-difference ambiguity to finally obtain the unbiased estimates of between-receiver differential phase bias (BR-DPB) and between-receiver differential code-phase bias (BR-DCPB) based on the short baseline mode. The key to this method is that the error sources can be significantly eliminated due to the length of the baseline is very short. At the same time, the empirical constraints and random characteristics of BR-DPB/BR-DCPB were considered, which is conducive to the resolution of single-difference ambiguity. Several sets of GNSS data (GPS L1/L2, Galileo E1/E5b, and BDS B1/B3), recorded by the short baselines in an interval of 30 s and covered a broad range of receiver/antenna types (JAVA, SEPT, LEIC, and TRIM), were used to verify the effectiveness of the proposed method. The numerical tests show that the proposed method is capable of fast fixing the single-difference ambiguity successfully within a few epochs and then providing the unbiased estimates of BR-DPB and BR-DCPB in an epoch-by-epoch manner. Experiments show that the estimated BR-DPB is in millimeter accuracy, which is of great significance for the millimeter-accuracy phase time transfer and ionospheric delay estimation. Furthermore, the calibrated BR-DPB/BR-DCPB can be treated as the known products for long-distance precise timing and ionosphere sensing based on the inter-station single-difference model.     

Evaluation of rapid phase clock/bias products for PPP ambiguity resolution and its application to the M7.1 2019 Ridgecrest,California earthquake

Precise point positioning with ambiguity resolution (PPP-AR) is a useful tool for high-precision geodetic and geophysical applications, while phase bias products are the prerequisite to implement PPP-AR. Wuhan University has been providing the final (the best operationally post-processing solution based) phase clock/bias products with a latency of two weeks since March of 2019, while a dedicated open-source software package PRIDE PPP-AR is released to leverage these products for high-precision positioning. In order to satisfy some both time and precision critical applications, such as rapid earthquake response, Wuhan University also released rapid (with comparable quality but with much shorter delivery latency) phase clock/bias products with a latency of less than 24 h and updated PRIDE PPP-AR in July 2019. We first introduce the phase clock/bias generation and validation schemes and the maintenance of routine products provision. Then, with 14 days (July 2 to July 15 in 2019) of GPS data collected from 146 globally distributed IGS (International GNSS Service) stations, we evaluated the positioning performance of the rapid products with respect to their final counterparts. It is found that positioning precision of PPP-AR using rapid products is comparable to that using final products, especially in kinematic positioning mode. When rapid products are used, the RMS of PPP-AR in static mode with respect to IGS weekly solutions can reach 1.7 mm, 1.8 mm and 5.5 mm in the east, north and up components, respectively. Furthermore, the RMS of epoch-wise positions with respect to daily solutions for the east, north and up components are 0.51 cm, 0.57 cm and 1.51 cm for PPP-AR with rapid products in kinematic mode. It demonstrates that the rapid phase clock/bias products can sufficiently meet the precision requirement of most geodetic and geophysical applications yet with much shorter time delay. Finally, we study the July 6th M7.1 2019 Ridgecrest, California earthquake using the rapid phase clock/bias products and demonstrate their comparable performance against the final products.     

Estimation of differential code biases with Jason-2/3 onboard GPS observations

With the continuous deployment of Low Earth Orbit (LEO) satellites, the estimation of differential code biases (DCBs) based on GNSS observations from LEO has gained increasing attention. Previous studies on LEO-based DCB estimation are usually using the spherical symmetry ionosphere assumption (SSIA), in which a uniform electron density is assumed in a thick shell. In this study, we propose an approach (named the SHLEO method) to simultaneously estimate the satellite and LEO onboard receiver DCBs by modeling the distribution of the global plasmaspheric total electron content (PTEC) above the satellite orbit with a spherical harmonic (SH) function. Compared to the commonly used SSIA method, the SHLEO model improves the GPS satellite DCB estimation accuracy by 13.46% and the stability by 22.34%, respectively. Compared to the GPS satellite DCBs estimated based on the Jason-3-only observations, the accuracy and monthly stability of the satellite DCBs can be improved by 14.42% and 26.8% when both Jason-2 and Jason-3 onboard observations are jointly processed. Compared with the Jason-2 solutions, the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations have an improved consistency of better than 18.26% and 9.71% with the products provided by the Center for Orbit Determination in Europe (CODE) and Chinese Academy of Sciences (CAS). Taking the DCB products provided by the German Aerospace Center (DLR) as references, there is no improvement in accuracy of the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations than the Jason-2 solutions alone. A periodic variation is found in the time series of both the Jason-3 and Jason-2 onboard receiver DCB estimates. Preliminary analysis of the PTEC distribution based on the estimated SH coefficients are also presented.     

Correction model of BDS satellite-induced code bias and its impact on precise point positioning

There are code biases on the pseudo-range observations of the Beidou Navigation Satellite System (BDS) that range in size from several decimeters to larger than one meter. These biases can be divided into two categories, which are the code biases in the pseudo-range observations of Inclined Geo-Synchronous Orbit (IGSO) satellites and Medium Earth Orbit (MEO) satellites and the code biases in the pseudo-range observations of Geosynchronous Earth Orbit (GEO) satellites. In view of the code bias of the IGSO/MEO satellites, the code bias correction model is established using the weighted least square curve fitting method. After the correction, the code biases of the IGSO and MEO satellites are clearly mitigated. A methodology of correcting GEO code bias is proposed based on the empirical mode decomposition (EMD)-wavelet transform (WT) coupled model. The accuracies of the GEO multipath combination of the B1, B2 and B3 frequencies are improved by 39.9%, 17.9%, and 29.4%, respectively. Based on the corrections above, the ten days observations of three Multi-GNSS Experiment (MGEX) stations are processed. The results indicate that the convergence time of the precise point positioning (PPP) can be improved remarkably by applying a code bias. The mean convergence time can be improved by 14.67% after the IGSO/MEO code bias correction. By applying the GEO code bias, the mean convergence time can be further improved by 17.42%.     

小数偏差产品质量评估及固定性能分析

为了评估不同小数偏差产品的数据质量和模糊度固定效果，比较了2016年全年的SGG FCB产品和CNES产品，结果表明两种产品具有很高的一致性，SGG FCB产品的数据完整性更好。应用两种产品进行精密单点定位(PPP)固定解的静态结果平面位置精度可以达到1 cm以内，高程位置精度可以达到1~2 cm，采用两种产品获得的PPP模糊度固定率十分接近，动态模式下处理静态数据的位置结果可以达到平面2~3 cm，高程5 cm以内的精度，两组固定解的位置误差结果差异不超过5 mm，模糊度固定成功率分别为92.37%和92.14%，两种小数偏差产品在23分钟左右完成首次固定，能够有效提高PPP的收敛速度。使用两种小数偏差产品得到的机载动态数据结果也非常相近。     

Tightly combined GPS/Galileo RTK for short and long baselines: Model and performance analysis

To ensure the compatibility and interoperability with modernized GPS, Galileo satellites are capable of broadcasting navigation signals on carrier phase frequencies that overlap with GPS, i.e., GPS/Galileo L1-E1/L5-E5a. Moreover, the GPS/Galileo L2-E5b signals have different frequencies with wavelength differences smaller than 4.2?mm. Such overlapping and narrowly spaced signals between GPS and Galileo bring the opportunity to use the tightly combined double-differenced (DD) model for precise real-time kinematic (RTK) positioning, resulting in improved performance of ambiguity resolution and positioning with respect to the classical standard or loosely combined DD model. In this paper, we focus on the model and performance assessment of tightly combined GPS/Galileo L1-E1/L2-E5b/L5-E5a RTK for short and long baselines. We first investigate the tightly combined GPS/Galileo DD observational model for both short and long baselines with simultaneously considering the GPS/Galileo overlapping and non-overlapping frequencies. Particularly, we introduce a reparameterization approach to solve the rank deficiency that caused by the correlation between the DISB parameters and the DD ionospheric parameters for both overlapping and non-overlapping frequencies. Then we present performance assessment for the tightly combined GPS/Galileo RTK model with real-time estimation of the differential inter-system bias (DISB) parameters for short and long baselines in terms of ratio value, ambiguity dilution of precision (ADOP), ambiguity conditional number, decorrelation number, search count, empirical success rate, time-to-first-fix (TTFF), and positioning accuracy. Results from both static and kinematic experiments demonstrated that compared to the loosely combined model, the tightly combined model can deliver improved performance of ambiguity resolution and precise positioning with different satellite visibility. For the car-driven short baseline experiment with 10° elevation cut-off angle, the tightly combined model can not only significantly increase the ratio value by approximately 27.5% (from 16.0 to 20.4), but also reduce the ambiguity ADOP, the conditional number, and the search count in LAMBDA by approximately 22.2% (from 0.027 to 0.021 cycles), 14.9% (from 199.2 to 169.6), and 25.4% (from 150.1 to 112.0), respectively. Comparable decorrelation number, empirical success rate, and positioning accuracy are also obtained. For the car-driven long baseline experiment, it is also observed that the ambiguity resolution performance in terms of the ratio value, the decorrelation number, the condition number, and the search count are significantly improved by approximately 18.5% (from 2.7 to 3.2), 22.0% (from 0.186 to 0.227), 55.9% (from 937.6 to 413.7), and 10.3% (from 43.8 to 39.3), respectively. Moreover, comparable ADOP, empirical success rate, and positioning accuracy are obtained as well. Additionally, the TTFF can be reduced (from 54.1 to 51.8 epochs with 10° elevation cut-off angle) as well from the results of static experiments.     

激光捷联惯导系统温度误差补偿研究

针对激光陀螺惯性导航系统中惯性器件零偏随温度变化的情况,在-30℃～+50℃温度范围内,通过大量的温度实验,建立了零偏与温度变化的多项式模型,并用该模型对实验数据进行了补偿,扣除地速和重力加速度的分量,惯性器件输出几乎为零。最后在不同温度下进行了初始对准实验,实验结果表明：经过温度补偿后,在-30℃～+50℃ 温度内,俯仰角误差平均在0.0019° 以内,横滚角误差平均在0.0038°以内,航向角误差平均在0.014° 以内,接近了常温下的初始对准精度,满足了系统的指标要求。