提高空间环模设备中铝热沉高真空气密性的工艺措施

我国大型空间环境模拟器的铝热沉,工作于-196～+100℃的温度,内压最高1.6MPa。其中主容器热沉是一个直径10.5m、高20m 的鼠笼形立式铝列管热交换器。整个热沉由2500多根铝管焊接而成,焊缝数量超过5000道。热沉有很严格的真空气密性要求,整个热沉的总漏率要求不大于1×10~(-6)Pa·m~3/s。文章分别从管件检测、纯铝焊接、高真空检漏等方面论述了确保热沉高真空气密性的措施。     

Variation of the orbital elements for parabolic trajectories due to a small impulse using Gauss equations

Firstly we derive Gauss’ perturbation equation for parabolic motion using Murray–Dermott and Kovalevsky procedures. Secondly, we easily deduce the variations of the orbital elements for the parabolic trajectories due to a small impulse at any point along the path and at the vertex of the parabola.     

物体—双伞系统运动方程与稳定性判据

利用刚体－双刚体模型给出了物体－双伞系统的运动方程与一种简化模式，并按运动稳定性分析的原理求得了该系统的稳定性判据。     

FMCW体制毫米波SAR实时信号处理方法研究

与脉冲体制合成孔径雷达(SAR)相比,调频连续波(FMCW)体制SAR具有体积小、重量轻、分辨率高、功耗低和低截获等一系列优点,目前小型或微小型SAR普遍采用FMCW工作体制。FMCW SAR在整个脉冲重复周期内都发射信号,其信号占空比达到了100%,为了减小数字接收机采样带宽,降低数据率,FMCW体制毫米波SAR一般采取解线频调接收的方式,但其数据量依然很大,而且机载平台受到气流的影响,运动误差很大,需要迭代估计与补偿,给实时处理模块带来了很大压力。为了提高整个机载FMCW SAR系统的信号实时处理性能,需要在算法层面进行改进。提出了一种两次子孔径误差估计和全孔径误差拼接补偿的FMCW SAR实时成像算法,使用相位梯度自聚焦(PGA)算法和图像偏置(MD)算法级联提取子孔径误差;然后进行子孔径误差拼接成全孔径误差补偿原数据,两维脉冲压缩后完成图像聚焦,提高了FMCW体制毫米波SAR成像算法的效率;最后使用机载Ka波段FMCW SAR实测数据,验证了该算法的有效性。     

Evaluation of airborne data link communication

An experimental prototype of a cockpit data link communication interface (modified Navigation Display (ND) and Multi-purpose Control and Display Unit (MCDU)) was developed and tested in an Airbus A340 Full Flight Simulator. 8 crews (16 professional pilots) performed simulator flights in a mixed voice and data link scenario. After each experiment video recordings were presented to the pilots and they were asked to estimate subjective strain (NASA task load index) and situational aspects retrospectively. Results show an increase in subjective strain and a decrease of ‘feeling of sovereignty’ and situation awareness under data link conditions. The effect is similar to the one caused by higher workload.     

Matching design of hydraulic load simulator with aerocraft actuator

 This paper intends to provide theoretical basis for matching design of hydraulic load simulator (HLS) with aerocraft actuator in hardware-in-loop test, which is expected to help actuator designers overcome the obstacles in putting forward appropriate requirements of HLS. Traditional research overemphasizes the optimization of parameters and methods for HLS controllers. It lacks deliberation because experimental results and project experiences indicate different ultimate performance of a specific HLS. When the actuator paired with this HLS is replaced, the dynamic response and tracing precision of this HLS also change, and sometimes the whole system goes so far as to lose control. Based on the influence analysis of the preceding phenomena, a theory about matching design of aerocraft actuator with HLS is presented, together with two paired new concepts of "Standard Actuator" and "Standard HLS". Further research leads to seven important conclusions of matching design, which suggest that appropriate stiffness and output torque of HLS should be carefully designed and chosen for an actuator. Simulation results strongly support that the proposed principle of matching design can be anticipated to be one of the design criteria for HLS, and successfully used to explain experimental phenomena and project experiences.     

耦合六自由度运动弹性飞机阵风响应数值模拟

耦合飞机刚体六自由度运动,考虑飞机结构气动弹性变形,基于全湍流Navier—Stokes方程流场数值模拟方法．建立了离散阵风作用下弹性飞行器气动载荷与飞行姿态响应的数值模拟技术。其中模态空间中结构动力学方程以及六自由度运动方程分别采用四阶R—K进行时间推进求解,采用RadialBasicFunction（RBF）技术进行气动／结构数据耦合。对应飞机姿态以及弹性变形采用RBF与TFI组合模式的动网格方法进行网格更新;以飞翼布局弹性飞机为数值研究对象,研究了离散阵风作用下飞行器的气动载荷响应以及飞行姿态的变化,对比分析了刚性飞行器与弹性飞行器对离散阵风响应的区别,为进一步系统地分析真实飞机飞行品质提供数值平台。     

An experimental study of the dual-loop control of electro-hydraulic load simulator （EHLS）

This paper investigates motion coupling disturbance（the so called surplus torque）in the hardware-in-the-loop（HIL）experiments.The＇＇velocity synchronization scheme＇＇was proposed by Jiao for an electro-hydraulic load simulator（EHLS）in 2004.In some situations,however,the scheme is limited in the implementation for certain reasons,as is the case when the actuator＇s valve signal is not available or it is seriously polluted by noise.To solve these problems,a＇＇dual-loop scheme＇＇is developed for EHLS.The dual-loop scheme is a combination of a torque loop and a position synchronization loop.The role of the position synchronization loop is to decouple the motion disturbance caused by the actuator system.To verify the feasibility and effectiveness of the proposed scheme,extensive simulations are performed using AMESim.Then,the performance of the developed method is validated by experiments.     

基于逐次二点法三坐标测量机直线度运动误差的测量

分析了逐次二点法在三坐标测量机直线度运动误差测量方面的可行性,介绍了逐次二点法的测量原理,并定量分析了传感器及安装引起的误差。对现有的三坐标测量机进行测量,结果表明,采用逐次二点法对直线度运动误差测量实用可靠,可以满足测量的要求。