Modeling high-speed cutting of SiCp/Al composites using a semi-phenomenologically based damage model

In this paper, we attempts to investigate cutting mechanisms in high-speed cutting of Al6061/SiC_p/15p composites using a semi-phenomenologically based damage model in the equivalent homogeneous material (EHM) framework. By combining macroscale EHM modeling and underlying microscale physical mechanisms, a feasible semi-phenomenological plastic model is proposed for prediction of cutting forces and chip morphology during high-speed turning Al6061/SiC_p/15p composites. This model incorporates the modified Weibull weakest-link effect to represent the strain-based damage evolution in large deformations. This proposed semi-phenomenological constitutive model is implemented by compiling material subroutines into cutting finite element (FE) codes. The effects of the critical shear stresses on chip formation that depend on the tool-chip frictional coefficient are accounted for in the cutting FE model. The chip formation mechanism affecting material removal behaviors during high-speed turning is further investigated. The capabilities of the proposed constitutive model are evaluated by comparing cutting forces and chip morphologies between experiments and simulations at different cutting speeds associated with strain rates. The EHM-based and microstructure-based models are further compared in both computational efficiency and accuracy. The simulation results show that the developed semi-phenomenological constitutive formalism and cutting model are promising and efficient tools for further investigation of dynamic mechanical and cutting behaviors of particle-reinforced composites with different volume fraction and particle size.     

充气卸荷开关泄漏机理分析

某发射场进行火箭发动机气瓶充气时出现充气卸荷开关关闭后泄漏故障,分解卸荷开关后发现卸荷开关阀芯导向部位存在异常磨损,且阀芯非金属密封面周向密封压痕深度不均匀,结合故障形貌,采用有限元仿真计算压痕深度,对泄漏故障的根本原因进行深入剖析。分析结果表明:卸荷开关阀芯导向部位存在微小原始缺陷,多次动作后在阀芯与壳体导向部位产生粘着磨损,阀芯在壳体导向孔中回位发生偏斜,造成阀芯非金属密封面出现不均匀压痕,最终导致卸荷开关在测试时漏率超标。     

颗粒增强金属基纳米复合材料脉冲电沉积制备研究

采用脉冲电沉积,在普通碳钢表面制备了Ni-W-P／CeO2-SiO2颗粒增强金属基纳米复合材料,研究了脉冲峰值电流密度和脉冲占空比对电沉积过程的影响,采用纳米颗粒的质量百分含量、沉积速率、显微硬度和表面形貌进行表征。结果表明：增加脉冲峰值电流密度或脉冲占空比,Ni—W—P基质金属晶粒细化,CeO2和SiO2纳米颗粒的质量百分含量提高。当脉冲频率为1000Hz,脉冲峰值电流密度和脉冲占空比分别为40A／dm^2和50％时,沉积速率最快（56．24μm／h）,显微硬度最高（712Hv）。此时,Ni—W—P基质金属轮廓清晰,晶粒细小而均匀,CeO2和SiO2纳米颗粒以弥散态均匀分散在基质金属中。     

基于数据融合的边缘检测新方法研究

基于经典形态学的边缘检测方法虽然具有较好的去噪能力,但其得到的往往是断续的,不完整的边缘信息,不能反映全部的边缘特性.分别利用改进的数学形态学的方法和拉普拉斯算法对图像进行边缘检测,然后将两种方法处理后的图像进行数据融合,实验结果表明,该方法得到的图像边界细腻完整,具有较好的抗噪性.     

Automated determination of the orientation of dust devil tracks in mars orbiter images

The paper presents and evaluates three methods for automatically estimating the main orientation of Martian dust devil tracks in MOC and HiRISE images. Inferring such information about dust devils from their tracks is important to better understand the near surface wind. The methods considered were based on gradient direction, directional openings and morphological granulometry. The accuracy of the methods was asserted by comparing the results to a set of directions estimated visually and assumed to be the ground truth. The higher accuracy was reached using directional openings. Besides, the directions inferred by this method were compared to those predicted by the GCM and the results agreed.     

A robotic telescope network for space debris identification and tracking

The two TAROT (Télescopes à Action Rapide pour les Objets Transitoires; Rapid Action Telescopes for Transient Objects) installations are fully robotic optical observatories with optimized observation scheduling, data processing and archiving. Zadko is a 1 m telescope in Western Australia. The fully robotisation of the Zadko telescope has just been completed; it is now included in the TAROT network. In this paper we provide an overview of this international network of robotic optical telescopes. We discuss the advantages of using the network to participate in a satellite and space debris tracking program. This network will access almost all geostationary belt objects, and provide the first real-time satellite positioning capability. The inclusion of the 1 m Zadko telescope into the network significantly extends the efficiency and sensitivity of the existing two telescope configuration.     

电弧增材制造7075铝合金的微观组织与力学性能

7xxx系铝合金电弧增材制造过程中因组织不均匀与元素偏析导致成形试样性能较低,针对这一问题,对电弧增材制造7075铝合金薄壁件进行固溶+人工时效热处理(T6态),对比研究了热处理前后微观组织与力学性能的变化。结果表明,7075铝合金沉积态试样中晶粒被网状共晶组织包围,Zn、Mg和Cu元素在晶界富集,产生元素偏析。经过T6态热处理后,大部分共晶组织溶解,元素分布的不均匀性得到明显改善。与沉积态试样相比,热处理后试样的抗拉强度与断后伸长率增加,抗拉强度从(279.4±5.3)MPa提高至(493.9±10.2)MPa,断后伸长率从3.78%±0.35%增加到9.66%±1.70%。T6态试样的拉伸断口表面密布着韧窝,断裂方式为韧性断裂。     

PTFE/CFRP/铝合金叠层材料钻削试验研究

对PTFE/CFRP/铝合金叠层材料进行了钻削试验研究。结果表明:最高钻削温度随主轴转速的增大而增大,但随进给量的增大反而下降;相同钻削参数下,从铝合金侧钻入能获得更低的钻削温度;采用较大的进给量有利于铝合金形成碎屑状切屑,避免带状切屑排出时划伤已加工CFRP表面;采用较低主轴转速和较大的进给量可获得更好的铝合金孔出口质量。     

帕金森大鼠模型的影像特性

利用影像技术对帕金森病（Parkinsondisease，PD）大鼠模型的脑形态与功能信息进行了系统研究。利用磁共振（Magneticresonance imaging。MRI）及磁共振血管成像（Magneticresonanceangiography，MRA）获取PD大鼠脑部形态影像资料，利用质子磁共振波谱（1H—magneticreso—nancespectroscopy，1H—MRS）及CT灌注（CTperfusion，CTP）成像获取波谱及血流变化等功能影像学资料。研究结果表明PD大鼠在形态上影像无特征性异常，在功能影像学纹状体存在局部脑血流降低和波谱变化。     

混杂纤维复合材料层板的抗弹冲击性能

为了考察混杂纤维复合材料层板的抗弹冲击性能,采用碳纤维织物或玻璃纤维织物与芳纶纤维织物复合材料层共固化的方式,利用热压罐成型工艺制备了几种具有不同面密度及铺层结构的混杂纤维复合材料层板,并进行抗弹冲击性能测试、表观形貌观察和无损检测分析。结果表明:纯芳纶纤维及混杂纤维复合材料层板的钢弹冲击破坏模式相同,均为表层剪切破坏,中间层分层破坏,背层拉伸断裂破坏;层间混杂顺序对复合材料层板的分层缺陷面积有较大影响,当碳纤维层作为背层时,层板的分层缺陷面积为12 863. 6 mm2小于玻璃纤维层作为背层时(17 400. 5 mm2);当芳纶层作为背板时,混杂纤维复合材料层板冲击后分层缺陷面积与纯芳纶的相当(14 151. 0～14 927. 0 mm2)。混杂纤维复合材料对层板的抗弹冲击性能有较大影响,混杂后复合材料的弹道极限速度(v50)均有一定程度的提高,其中玻璃纤维/芳纶复合材料的v50从纯芳纶复合材料层板的193. 08提高至204. 33 m/s。将碳纤维层或玻璃纤维层作为着弹面层的混杂纤维复合材料层板具有更优异的抗弹冲击性能,其贯穿比吸能(BPI)均优于纯芳纶复合材料层板。