兆瓦级空间核电源碱金属朗肯循环热电转换系统设计

为解决火星探测任务中存在的星表供电问题,制定了以空间液态金属朗肯循环作为星表基地热电转换模块的任务规划,采用Simulink模块化建模方法对空间液态金属朗肯循环模型进行程序化描述.根据空间朗肯循环各部件的耦合标准,建立系统部件及总体控制仿真模型,重点研究变运行条件下循环输出功率的波动.研究表明:在本文各工况下,朗肯循环...     

涂层刀具低温铣削SiCp/Al复合材料表面质量研究

在加工过程中,相反的两相特性增加了 SiCp/Al复合材料加工难度,难以获得良好的表面质量.为了提高其切削性能,本文开展20vol％SiCp/Al复合材料铣削加工试验研究,比较常温和低温条件下TiAlN涂层和TiAlSiN涂层两种铣刀的切削性能.结果表明,在低温条件下,两种刀具的切削力增加,铣削后表面铝基体的开裂及剥落...     

面向航天应用的液态金属相变传热性能研究

为探究液态金属相变材料的适用范围，本文使用数值模拟手段，比较分析了以镓为代表的低熔点金属与以正十八烷为代表的石蜡类相变材料之间的传热性能。结果表明，镓更适用于应对瞬时高热流冲击，即高热流、短时间工作的电子设备散热；而正十八烷适用于低热流、较长时间工作的电子设备控温。此外，单位体积相变材料，镓模块的热控时间长于正十八烷模块；单位质量相变材料，镓模块在短时间内占优，长时间内正十八烷模块占优。针对潜在应用场景进行分析，表明了液态金属相变材料可用于航天天线TR组件和激光器芯片控温。     

Elliptical vibration cutting of large-size thin-walled curved surface parts of pure iron by using diamond tool with active cutting edge shift

Large-size thin-walled curved surface parts of pure iron are crucial in aerospace, national defense, energy and precision physical experiments. However, the high machining accuracy and surface quality are difficult to achieve due to the serious tool wear and deformation when machining the parts with conventional cutting tools. In this paper, an elliptical vibration cutting (EVC) with active cutting edge shift (ACES) based on a long arbor vibration device is proposed for ultra-precision machining the pure iron parts by using diamond tool. Compared with cutting at a fixed cutting edge, the influence of ACES on the EVC was analyzed. Experiments in EVC of pure iron with ACES were conducted. The evolutions of the surface roughness, surface topography, and chip morphology with tool wear in EVC with ACES are revealed. The reasonable parameters of ultra-precision machining the pure iron parts by EVC with ACES were determined. It shows that the ACES has a slight influence on the machined surface roughness and surface topography. The diamond tool life can be significantly prolonged in EVC of pure iron with ACES than that with a fixed cutting edge, so that high profile accuracy and surface quality could be obtained even at higher nominal cutting speed. A typical thin-walled curved surface pure iron part with diameter ∅240 mm, height 122 mm, and wall thickness 2 mm was fabricated by the presented method, and its profile error and surface roughness achieved PV 2.2 μm and Ra less than 50 nm, respectively.     

A novel method of utilizing static mixer to obtain mixing homogeneity of multi-species powders in laser metal deposition

Real-time mixing of multi-species powder challenges Laser Metal Deposition (LMD) of Functionally Graded Materials (FGMs). The current work proposes a novel method of using a static mixer to realize rapid, uniform multi-species powder mixing. Firstly, copper powder and 316L stainless steel powder are selected to complete the powder mixing observation experiment with Scanning Electron Microscope (SEM) and Energy Dispersive Spectrometer (EDS). Secondly, computational fluid dynamics and particle mixing simulation models are used to analyze the flow field and particle motion characteristics in the static mixer. Finally, LMD experiment and metallographic observation are carried out with 316L stainless steel powder and WC powder to verify the feasibility of the static mixer. This study provides a theoretical and practical basis for powder mixing in laser processing with a static mixer. The conclusions can also be applied to other processing fields requiring real-time and uniform mixing of multi-species powders.     

基于液体金属的接触PIM抑制方法和实验验证

接触非线性是射频设备和电路中产生无源互调（passive intermodulation，PIM）信号的重要原因之一。基于对接触结点射频等效电路的分析，提出了一种基于共晶镓铟合金（eutectic gallium-indium，EGaIn）的PIM抑制方法。EGaIn不同于传统的焊锡，它可以在室温下实现接触结位置上的稳定、可重构连接。首先分析了射频（radio frequency，RF）下的金属接触结的电路模型。其次设计并实现了两个包含不同金属接触结构且工作在2.6GHz的平面倒F天线（planar inverted F antenna，PIFA）。最后比较了EGaIn焊接前后PIFA的互调水平，其中对PIM指标的最大抑制程度为35dB。验证了EGaIn可以在室温下对PIFA的接触结点进行可重构焊接，这为电连接中的非线性抑制提供了一种参考方法。     

微织构刀具对钛合金切屑形成影响的仿真研究

针对微织构刀具对钛合金Ti6Al4V切屑形成以及微槽二次切削机理分析的不足，通过建立热-力耦合仿真模型对比研究不同微织构刀具、微织构几何尺寸以及切削速度对切屑形成的影响规律。数值仿真结果表明：微织构刀具更有利于断屑，二次切削作用使切屑的弯曲半径变大，微织构可以减小刀屑之间实际接触面积，降低切削温度。增大微织构宽度可以增强微槽的二次切削作用，利于断屑，但应注意其对刀具强度的削弱作用，而增大相邻微槽间距则会出现相反的二次切削作用机制。提高切削速度对各刀具均有利于断屑，弧形微织构刀具的降温效果最好，V形微织构刀具次之，矩形微织构刀具降温效果最差。研究结果对进一步理解微织构刀具对钛合金切屑的二次切削作用机理提供一定参考。     

超声振动辅助切削对碳纤维增强树脂复合材料面下损伤影响的仿真研究

碳纤维增强树脂基复合材料（CFRP）在传统加工（OC）过程中存在着切削力过大、表面质量不佳、面下损伤较为严重等问题。为了改善上述问题，本文提出使用超声振动辅助切削（UVC）工艺加工CFRP，通过仿真分析对切削力与面下损伤深度进行研究。结果表明：使用UVC加工CFRP可降低13%~80%的切削力，且纤维方向角对切削力影响较小。与OC相比，UVC切削0°、45°纤维方向角的CFRP时可以减少约50%的面下损伤深度；在切削90°、135°纤维方向角的CFRP时虽然没有改善面下损伤深度，但取得了较为平整的已加工表面以及较小的损伤区域。     

Development and coupling test of active spacecraft potential control – Next generation (ASPOC-NG)

The active spacecraft potential control (ASPOC) system developed in the 1990s emits positive ions to neutralise the spacecraft potential, such as used in several missions like Geotail, Equator-S, Cluster, Doublestar and MMS. With the experience gained, the next generation of the active spacecraft potential control (ASPOC-NG) instrument has been developed over the last three years. Thereby, three emission technologies were tested including Liquid Metal Ion Source (LMIS), Liquid Metal Electron Source (LMES) and Solid Metal Electron Source (SMES). The development of the emitter module by FOTEC and the corresponding electronics control unit by IWF is presented. Optimisations were carried out with the focus on the reduction of mass and power consumption to comply with the requirements of future scientific missions. Coupling tests of the modules and the electronics control unit were performed including range, accuracy and lifetime tests. Both ASPOC-NG instruments for positive and negative charge compensation and their performance values show excellent results.     

中弧线角度分布对跨音叶栅特性影响研究

中弧线角度分布形式对压气机叶片表面等熵马赫数分布具有重要的影响。为了对比不同压气机叶型的流动特征，采用数值模拟和平面叶栅试验相结合，对两种中弧线角度分布形式的跨音叶型在不同来流工况下的气动特性展开了详细研究。结果表明：在设计点，前加载配合均匀加载的中弧线角度分布叶型能够消除叶片吸力面的局部超音区，与前加载的中弧线角度分布叶型相比，叶片表面等熵马赫数分布更加饱满。其次，前加载配合均匀加载叶型能够推迟叶片吸力面的涡层失稳，减弱了吸力面分离涡与端壁分离涡的耦合作用，进而改善了端区的流动状况，截面平均总压损失系数降低了8.2%。最后，对非设计工况下两种中弧线角度分布的气动特性进行了分析，随着来流马赫数的降低，两种中弧线角度分布叶型的损失差异逐渐减小，均具有较优的气动性能。来流速度对叶片表面等熵马赫数、损失分布和分离面形状特征影响较小，仅影响叶片表面等熵马赫数和损失数值大小。