涡轮导向器排气面积测量与分析

针对航空发动机涡轮导向器喉道面积科研生产的需求,研究发动机涡轮导向器喉道面积测量方法,解决发动机涡轮导向器喉道面积测量技术问题,满足发动机型号计量的需求,为航空发动机研制提供有力的保障.     

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

基于非接触式测量的旋转叶片动应变重构方法

基于叶端定时非接触式测量和振动响应传递比的概念,开展高速旋转叶片动应变重构方法的研究。在频域内推导了叶片任意测点位移与任意测点动应变的传递比,给出了单模态共振下响应传递比关于位移和应变模态振型的解析表达式;建立旋转叶片的三维(3D)有限元模型,开展考虑旋转预应力效应的叶片模态分析,提取位移和应变模态振型,获得任意转速下叶端位移与叶根关键点动应变的传递比。开展高速旋转叶片叶端定时非接触式测量实验,采用周向傅里叶算法对叶端定时信号进行处理,获得叶片在不同转速单模态共振下的叶端位移,结合响应传递比,重构5个旋转叶片的关键点动应变。结果表明:旋转叶片在9000r/min和13000r/min转速下发生1阶共振时,与应变片实测结果相比,叶根处应力最大点、次大点和边缘点3个关键点的动应变平均重构误差均小于15%,验证了旋转叶片动应变重构方法的有效性。     

基于PIV技术的单圆孔脉冲射流流场特征

对稳态射流及脉冲射流冲击靶板时的流场特性结构进行了探索和分析。采用高频粒子图像测速技术,在射流管口到冲击靶板间距为6倍管径的条件下,对稳态射流进口雷诺数为6 000的稳态射流及脉冲频率为20 Hz的脉冲射流进行了实验测量,得到了射流核心区、壁面射流区及滞止区内的速度分布。研究发现:①由于射流剪切作用的影响,脉冲射流核心区的最大轴向脉动速度为稳态射流的3倍。②滞止区内,由于射流的剪切作用和壁面的滞止作用,导致了脉冲射流轴向速度梯度最大为稳态射流的2倍,同时,滞止区内的最大脉动速度是稳态射流脉动速度的3倍。③脉冲射流对壁面的卷吸以及旋涡的产生和传播过程,破坏了壁面射流区稳定的速度边界层。相比稳态射流,脉冲射流的流场增加了湍流相干结构的含能并产生周期性的大尺度卷吸涡。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

关于多目标气动优化设计中伴随方法与对策理论的耦合研究(英文)

本文研究了多目标气动优化设计中伴随方法和对策理论的耦合问题,给出了伴随方法在每个对策策略中的具体应用和数值方法。在合作对策中伴随方法被并行地执行以共同得到Pareto阵面上的最优解;相反在Nash对策中伴随方法在Nash策略的最后被耦合起来以互相竞争的形式得到各自目标的最优解;而在Stackel-berg对策中伴随方法被分层耦合进"领头人"和"跟随者"的策略中以求解他们相互依赖的平衡解。文末的优化算例表明了本文耦合算法及其数值过程在求解多目标气动优化设计问题中的有效性。     

高精度反射面板制造中边值问题的求解方法(英文)

采用三层铝板两层蜂窝芯的夹层结构制造高精度反射面板是一种先进、复杂的技术。其中,单层铝板的受力分析和夹层板的回弹计算是成形精度的根本保障。利用Fourier级数表示单层板应力函数、利用幂级数表示夹层板挠度函数,分别对高精度反射面板制造中单层板压贴和夹层板回弹两类边值问题进行了求解。与有限元模拟结果对比表明,本文提出的单层板压贴膜应力计算Fourier级数法具有较高精度;与试验结果对比表明,本文提出的夹层板回弹量幂级数法具有满意精度。     

应用PIV技术测试模型环形燃烧室流场

采用粒子图像测速仪(PIV)测量带双级旋流器模型环形燃烧室内冷态和燃烧流场,试验研究不同进口气流温度对其冷态和燃烧流场内回流区的形成以及气流速度分布的影响,试验结果表明:燃烧室燃烧流场内回流区长度要比冷态流场短,燃烧流场的脉动速度明显大于冷态流场;另外随着进口气流温度增加,燃烧室冷态和燃烧流场的回流区长度都稍有减少.      

基于瞬态液晶测量技术的收缩-扩张形孔

采用一种进行全表面测量的瞬态液晶测量技术测量了新型气膜孔(收缩-扩张形孔)的气膜冷却特性,研究了动量比对冷却效率和换热系数的影响,并与传统的圆柱形孔气膜冷却特性进行了对比,结果表明:收缩-扩张形孔中心线附近区域的冷却效率相对较低,而两孔之间区域的冷却效率相对较高,与圆形孔分布规律相反;在上游区域,两孔中间区域的换热系数比相对孔中心线附近区域较高,而在下游区域,两孔中间区域的换热系数比相对孔中心线附近又较低,与圆形孔相比也有较大不同。相对于圆柱形孔,收缩缝形孔的平均换热系数比在上游较高,在下游较低;收缩-扩张形孔喷出气膜对下游壁面区域的有效覆盖率远大于圆柱形孔,其展向平均冷却效率明显高于圆柱形孔;收缩-扩张形孔在动量比为2时的平均冷却效率最高。     

崎岖地形中关节式月球车姿态估计数值求解方法

 以被动关节式地形自适应月球车为研究对象,融合关节机器人D-H坐标建模方法构建了月球车悬架运动学模型和以侧倾、俯仰和偏转角表示姿态的欧拉角方式建立了车轮到世界坐标系的悬架完整表达模型。利用悬架完整表达模型,用带有迭代因子的连续迭代和离散迭代数值求解方法,建立了光滑和离散崎岖地形姿态估计算法。最后以8轮扭杆双摇杆摇臂月球车原理样机为例来验证此模型求解方法。仿真结果验证了所建立的基于数值方法的崎岖地形被动关节式月球车姿态估计模型的正确性,其求解模型精度能够满足仿真要求。