Single track and single layer formation in selective laser melting of niobium solid solution alloy

Selective laser melting (SLM) was employed to fabricate Nb-37Ti-13Cr-2Al-1Si (at%) alloy, using pre-alloyed powders prepared by plasma rotating electrode processing (PREP). A series of single tracks and single layers under different processing parameters was manufactured to evaluate the processing feasibility by SLM, including laser power, scanning speed, and hatch distance. Results showed that continuous single tracks could be fabricated using proper laser powers and scanning velocities. Both the width of a single track and its penetration depth into a substrate increased with an increase of the linear laser beam energy density (LED), i.e., an increase of the laser power and a decrease of the scanning speed. Nb, Ti, Si, Cr, and Al elements distributed heterogeneously over the melt pool in the form of swirl-like patterns. An excess of the hatch distance was not able to interconnect neighboring tracks. Under improper processing parameters, a balling phenomenon occurred, but could be eliminated with an increased LED. This work testified the SLM-processing feasibility of Nb-based alloy and promoted the application of SLM to the manufacture of niobium-based alloys.     

片光反射遮挡式超高速亚毫米粒子探测技术

为满足在超高速碰撞靶上开展航天器抗空间碎片防护性能试验,需要准确测量速度3～10km／s,以及更高速度的毫米级或亚毫米级粒子的飞行速度,在可以实现毫米级粒子探测的片光遮挡式粒子探测技术基础上发展了片光反射遮挡式粒子探测技术,通过采用提高粒子直径与激光光束宽度的比值,解决了探测粒子直径小于1mm时探测信号弱不能识别等关键技术,研制了试验装置并开展了验证试验,研究结果表明该技术在0．2～10km／s速度范围内可实现直径为0．1mm量级粒子的有效探测。     

光干涉技术在纳米精度测量中的应用及发展

分析了几种应用于纳米精度测量的光干涉技术工作原理、应用限制及研究现状,包括X射线干涉仪、干涉仪及激光外差干涉技术。     

激光捷联惯导系统角增量输入姿态算法

在对经典理想角增量输入的圆锥算法分析总结基础上,提出并推导了更为合适的经典角增量输入圆锥算法通式.在对经典理想角增量与实际工程滤波角增量的圆锥响应对比分析基础上,推导了滤波角增量输入圆锥补偿算法的补偿系数和误差主项通式.最后,利用文中讨论的理想角增量输入和滤波角增量输入圆锥补偿算法,结合激光陀螺惯性导航系统的频谱特性进行了大量的仿真验证.仿真结果表明,文中讨论的角增量圆锥算法有效,能显著提高激光陀螺捷联惯性导航系统的姿态精度.     

影响Al2O3凝相尺寸分布的因素

用激光全息装置测量含铝复合推进剂燃烧场凝聚相的分布，分辨率为5μm。分析了滞留时间、铝粉含量（2％－16％）和燃烧室压强（0.1MPa-4MPa）对凝相粒子尺寸分布的影响，实验表明，粒子总数随滞留时间减少，粒子越大，减少的相对比例越大；粒子尺寸分布不随燃烧室压强和推进剂铝粉含量变化。     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。     

The Genesis Solar Wind Concentrator Target: Mass Fractionation Characterised by Neon Isotopes

The concentrator on Genesis provided samples of increased fluences of solar wind ions for precise determination of the oxygen isotopic composition. The concentration process caused mass fractionation as a function of the radial target position. This fractionation was measured using Ne released by UV laser ablation and compared with modelled Ne data, obtained from ion-trajectory simulations. Measured data show that the concentrator performed as expected and indicate a radially symmetric concentration process. Measured concentration factors are up to ∼30 at the target centre. The total range of isotopic fractionation along the target radius is 3.8%/amu, with monotonically decreasing ²⁰Ne/²²Ne towards the centre, which differs from model predictions. We discuss potential reasons and propose future attempts to overcome these disagreements.     

Microstructure,porosity and mechanical properties of selective laser melted AlSi10Mg

Finite element modeling(FEM), microscopy, X-ray computed tomography(CT) and mechanical property tests were used to study the microstructure, porosity and mechanical properties of an AlSi10Mg alloy produced by selective laser melting(SLM). The simulation of the melt pool and thermal history under different energy densities produced an optimized result with an energy density of 44.5 J·mm^-3. The high cooling rate during the SLM process significantly refined the previous a-Al dendrites. T...     

三维激光成像系统的点云模型真彩色处理方法

三维激光成像系统获得的点云数据精度高并且保有高精度的高程信息,然而特征信息不明显,没有保留全部的点和点的拓扑关系,无法直接判读地面物体;影像数据空间分辨率和精度低,并且缺少高程信息,然而其影像的特征连续,光谱信息丰富.因此,进行点云数据与影像数据融合方法的研究是目前三维激光成像系统研制的前沿性课题.针对点云数据与影像数据融合方法的研究,提出了一种三维激光成像系统点云模型真彩色处理的方法.实验结果显示,采用所提出的方法,不仅能够获得被扫描物体的位置信息和大小信息,而且能够得到被扫描物体的表面纹理细节信息.     

300M钢激光熔覆耐磨防腐自润滑涂层温度场数值模拟研究

为了提高飞机起落架减震支柱300M超高强钢的抗磨性能,突破由于温度梯度过大诱发的激光熔覆耐磨防腐自润滑涂层裂纹等技术瓶颈,基于ANSYS软件的生死单元法编制热循环程序,考虑自润滑相和耐磨相材料热物性参数随温度的变化、相变潜热、激光熔覆过程中与外界的换热、激光熔覆功率、激光熔覆扫描速率等因素对激光熔覆过程温度场、熔池、温度梯度的影响,建立300M超高强钢激光熔覆耐磨防腐自润滑涂层温度仿真模型。结果表明:基体的熔化需要激光、熔化的粉末等综合作用使传导到该区域的有效能量达到熔化的临界值,熔化高度增加率随激光功率的增加先降低后增加,熔化高度减少率随激光扫描速率的增加先变小后变大;由于激光熔覆的不同区域温度、冷却速率差异等综合因素影响,熔覆层熔池的纵截面为勺状熔池;伴随激光功率的增加,由于熔覆层不同区域对能量输入产生的温度响应速率差异导致Z方向温度梯度值增加,且最大冷却速率增加;伴随激光扫描速率的增加,激光输入能量降低,降低了高温区域温度及激光的快速局部加热等综合影响,Z方向温度梯度值降低。通过调控激光参数,在保持熔覆层结合强度的条件下,基体熔凝区能被控制到最小,并能够降低温度梯度。