离子电推进技术的发展现状与未来

离子电推进是最具代表性和技术成熟度的电推进技术类型之一。本文从放电室技术、离子光学系统技术、放电阴极和中和器阴极技术的优势、缺憾等方面,总结了离子电推进的技术发展现状。针对未来航天任务对离子电推进更大功率、更高比冲、更简系统等新需求,分析了传统离子电推进所面临的主要技术挑战,梳理出了环型离子电推进、双级加速离子电推进、自中和离子电推进、螺旋波放电离子电推进等创新离子电推进技术发展的未来方向。     

20 cm离子推力器羽流对微波通信影响的试验研究

离子推力器工作时产生的等离子体羽流会对穿过其间的电磁波产生影响。为了解通信微波在羽流中的传输特性,在带有透波真空舱的专用设备上进行了羽流对微波通信影响的试验。采用的方法是将一对发射和接收双脊喇叭天线口紧贴透波舱两侧并正对放置来测试穿过羽流的通信微波的变化情况。试验结果表明:在1～5 GHz微波通信频段范围内,离子推力器所产生的羽流对电磁波的波幅和相位影响较小,幅度衰减不超过4 dB,相位偏差不超过80°。     

20 cm离子推力器电磁辐射试验研究

离子推力器工作时会产生对外电磁辐射,因此离子电推进应用于航天器时存在电磁兼容性问题。为初步了解离子推力器工作产生的电磁辐射特性,利用经改造后的地面专用试验系统进行了20 cm离子推力器电磁辐射测试试验。文章介绍了20 cm离子推力器电磁辐射的试验方案,采用两种形式进行:推力器电场辐射发射试验,测试频段为10 kHz～5 GHz;推力器瞬态电场辐射发射试验,测试频段为100 kHz～5 GHz。试验结果表明:在离子电推进稳态工作过程和几个瞬态工况点,未发生电磁干扰现象。     

超高速机械密封副离子注入与摩擦学特性研究

超高速机械动密封需满足CZ-5运载火箭伺服系统中涡轮泵可靠性及寿命指标要求。离子注入作为重要的金属材料表面改性技术,对有效改善机械密封副旋转环表面摩擦磨损特性至关重要。在对密封动环表面离子注入可行性研究的基础上,提出了对其密封副配对摩擦磨损特性进行综合验证的试验方案。通过选取常用典型石墨与旋转金属环配副进行干磨条件下的试验测试,改变线速度、端面比压,使用摩擦磨损试验机对比分析了配对摩擦副的摩擦磨损特性,系统研究了载荷和转速对密封副配对摩擦系数的影响规律,揭示其密封摩擦学特性。通过机械密封在温度应力下的工作可靠性分析以及密封副整机稳态工作性能验证,为超高速涡轮泵的寿命与可靠性试验验证提供了一个合理的、高效费比的技术途径。     

超低轨道卫星应用离子电推进技术方案

低地球轨道大气环境对诸如科学探测和对地观测卫星的阻尼作用十分明显,而且阻尼随太阳和地磁活动以及昼夜、季节交替变化范围宽.为了保证卫星轨道精度或飞行状态满足任务要求,需要利用推进系统对卫星受到的阻尼进行实时或间歇式补偿以实现轨道或飞行状态的保持.针对轨道高度220～268 km的无拖曳飞行和轨道维持应用,基于卫星轨道阻尼...     

Spectroscopic Constraints on Models of Ion-cyclotron Resonance Heating in the Polar Solar Corona

Using empirical velocity distributions derived from UVCS and SUMER ultraviolet spectroscopy, we construct theoretical models of anisotropic ion temperatures in the polar solar corona. The primary energy deposition mechanism we investigate is the dissipation of high frequency (10-10000 Hz) ion-cyclotron resonant Alfvén waves which can heat and accelerate ions differently depending on their charge and mass. We find that it is possible to explain the observed high perpendicular temperatures and strong anisotropies with relatively small amplitudes for the resonant waves. There is suggestive evidence for steepening of the Alfvén wave spectrum between the coronal base and the largest heights observed spectroscopically. Because the ion-cyclotron wave dissipation is rapid, even for minor ions like O⁵⁺, the observed extended heating seems to demand a constantly replenished population of waves over several solar radii. This indicates that the waves are generated gradually throughout the wind rather than propagated up from the base of the corona. This revised version was published online in June 2006 with corrections to the Cover Date.     

公差原则中相关要求的计算问题

关于公差原则中的相关要求的计算问题 ,本文提出了两种方法 :计算法和图解法。运用这两种方法可以简化此类问题的计算过程 ,准确求得计算结果。     

RAYTHEON 10SS雷达气象波束开关告警的产生及排除

自昆明西山雷达站RAYTHEON／＆司的10SS一次雷达投产以来，出现过3次气象波束开关告警，告警的现象均为A／B两个通道频繁交替告警，经过检查一次是由于天线平台的信号电缆头问题所致，另外两次是因为旋转铰链的电刷问题所致，本文将当时排除故障的情况和想法写出来，和大家一起来讨论今后如何更好地排除该故障。     

高效离子电热水器的设计

描述一种由AT89C2051单片机控制的高效离子电热水器，该热水器使用安全，即开即热，转换效率高。     

Fabrication of Diamond-like Carbon Films by Ion Assisted Middle Frequency Unbalanced Magnetron Sputtering

Diamond-like carbon （DLC） films are deposited by the Hall ion source assisted by the mid-frequency unbalanced magnetron sputtering technique. The effects of the substrate voltage bias, the substrate temperature, the Hall discharging current and the argon/nitrogen ratio on the DLC film＇s performance were studied. The experimental results show that the film＇s surface roughness, the hardness and the Young＇s modulus increase firstly and then decrease with the bias voltage incrementally increases. Also when the substrate temperature rises, the surface roughness of the film varies slightly, but its hardness and Young＇s modulus firstly increase followed by a sharp decrease when the temperature surpassing 120 ℃. With the Hall discharging current incrementally rising, the hardness and Young＇s modulus of the film decrease and the surface roughness of the film on 316L stainless steel firstly decreased and then remains constant.