基于简化Mohr模型的光纤陀螺温度补偿方法研究

为了提高光纤陀螺温度补偿精度,采用Mohr理论建立了光纤环圈的热传递模型,准确分析了光纤环圈内部的温度变化和分布情况,计算得到了光纤环圈的Shupe误差。根据Shupe理论误差和陀螺仪输出的相关性分析,得到了最优的光纤环圈热传递参数。根据热传递参数建立了光纤陀螺温度补偿模型,完成了光纤陀螺的实时温度补偿,实际补偿后光纤陀螺仪变温精度提高了约3.4倍。     

空间自旋目标平动补偿与微动特征提取方法

针对空间自旋目标平动补偿与微动(m-D)特征提取问题,提出一种基于延时共轭相乘和微动分解的平动补偿与特征提取方法。该方法通过延时共轭相乘处理实现目标加速度估计,然后构建冗余的微动原子集,对加速度补偿后信号进行微动分解补偿,通过搜索补偿信号的最大谱峰获取目标的微动特征与速度信息。仿真试验表明,所提方法能够有效估计空间自旋目标的运动参数,并快速提取其微动特征。     

舵机滚珠丝杠在内部热源作用下响应特性

舵机滚珠丝杠在运行过程中由于摩擦作用和电机运行产生的内部热源会导致其结构温度上升和变形,是影响滚珠丝杠副运行精度的因素之一。本文基于有限元理论建立舵机滚珠丝杠副模型,并通过在ANSYS Workbench中插入命令流的方式实现了在滚珠丝杠上施加移动摩擦热载荷,获得了滚珠丝杠副在内部热源作用下的温度、变形和应力响应特性。结果表明:滚珠丝杠轴向热流密度呈双峰趋势,且其高温区域主要集中在螺母行程范围内的中间区域;随着转速的增加,滚珠丝杠各处温度及其波动幅度加大;丝杠最大热应力位于与轴承配合的轴肩最外侧处。     

火电厂汽包水位测量及误差分析

汽包水位信号的准确测量直接关系到机组的安全稳定运行及汽水调节的品质，是机组安全、稳定运行的重要保证，因此需要采取必要措施提高汽包水位的测量精度并减少测量误差。本文介绍了汽包水位常用的测量方法、汽包水位测量误差产生的原因以及因汽包压力及取样管温度引起的水位测量误差的校核计算方法，提出r适用于发电厂汽包水位校核计算及实际补偿的通用原理和试验方法。     

J2级经纬仪竖盘指标自动补偿误差不确定度

介绍了按照ＪＪＧ４１４—９４《光学经纬仪》检定、校准Ｊ２级经纬仪竖盘指标自动补偿误差时，依据“’９３国际指南”要求，对其测量不确定度进行的分析、计算。     

针栓式喷注单元膜束撞击雾化混合过程数值模拟

为了全面认识针栓式喷注器喷雾场结构，基于自适应网格加密技术和分三相计算的PLIC VOF（Piecewise Linear Interface Calculation Volume of Fluid）方法对针栓式喷注单元膜束撞击雾化混合过程进行了仿真分析，通过对两路推进剂分别进行界面追踪，获得了膜束撞击雾化混合过程的详细结构特征，与高速摄影试验结果定性定量对比均吻合较好，验证了数值方法的准确性。以此为基础对膜束撞击的喷雾场结构、撞击变形过程、流场涡结构、雾化破碎典型特征及破碎后的雾化混合分布特征进行了识别分析，结果表明：膜束撞击形成了液束未穿透液膜和液束穿透液膜2种不同的喷雾扇结构。膜束撞击形成的喷雾扇呈"Ω"形，膜束同时发生弯曲变形和横截面变形。另外，膜束撞击同时受到正压和剪切应力作用，导致了一系列复杂涡流现象，使得相互作用增强，雾化混合均增强，这也是膜束撞击喷注构型优于膜膜撞击的本质原因。最后，还发现膜束撞击喷雾场液滴分布呈现分区结构特征，分别是液束控制主导的上雾化区、液膜控制主导的下雾化区及夹在中间的混合区，实际中应兼顾雾化特性和混合特性，选取中等动量比膜束撞击，这可为针栓式喷注器的理论研究和工程设计提供重要参考。     

Determination of optimal samples for robot calibration based on error similarity

Industrial robots are used for automatic drilling and riveting.The absolute position accuracy of an industrial robot is one of the key performance indexes in aircraft assembly,and can be improved through error compensation to meet aircraft assembly requirements.The achievable accuracy and the difficulty of accuracy compensation implementation are closely related to the choice of sampling points.Therefore,based on the error similarity error compensation method,a method for choosing sampling points on a uniform grid is proposed.A simulation is conducted to analyze the influence of the sample point locations on error compensation.In addition,the grid steps of the sampling points are optimized using a statistical analysis method.The method is used to generate grids and optimize the grid steps of a Kuka KR-210 robot.The experimental results show that the method for planning sampling data can be used to effectively optimize the sampling grid.After error compensation,the position accuracy of the robot meets the position accuracy requirements.     

基于全局Newton-Raphaon方法的弹流润滑分析

基于全局Newton-Raphaon方法对滑动轴承的弹流润滑性能进行了数值摸拟。比较了弹性变形对连杆大头轴承最小油膜厚度和最大油膜压力的影响。结果表明:全局Newton-Raphaon方法很好的解决了收敛困难,程序运行时间长的问题;考虑表面弹性变形的连杆大头轴承与刚性轴承相比,最小油膜厚度与最大油膜压力的变化趋势相同;一个工作循环内,弹性轴承的最小油膜厚度略大于刚性轴承,而最大油膜压力则明显减小。     

Application in prestiction friction compensation for angular velocity loop of inertially stabilized platforms

To overcome the influence of the nonlinear friction on the gimbaled servo-system of an inertial stabilized platforms(ISPs) with DC motor direct-drive, the methods of modeling and compensation of the nonlinear friction are proposed. Firstly, the inapplicability of LuGre model when trying to interpret the backward angular displacement in the prestiction regime is observed experimentally and the reason is deduced theoretically. Then, based on the dynamic model of direct-drive ISPs, a modified LuGre model is proposed to describe the characteristic of the friction in the prestiction regime. Furthermore, the state switch condition of the three friction regimes including presliding, gross sliding and prestiction is presented. Finally, a composite compensation controller including a nonlinear friction observer and a feedforward compensator based on the novel LuGre model is designed to restrain the nonlinear friction and to improve the control precision. Experimental results indicate that compared with those of the conventional proportion–integration–differentiation(PID) control method and the PID plus LuGre model-based friction compensation method, the dwell-time has decreased from 0.2 s to almost 0 s, the position error decreased to 86.7%and the peak-to-peak value of position error decreased to 80% after the novel compensation controller is added. It concludes that the composite compensation controller can greatly improve the control precision of the dynamic sealed ISPs.     

BTA 深孔钻削切屑变形与刀齿切削力分布规律仿真

采用ABAQUS有限元分析软件,建立了错齿BTA钻头钻削环状工件单元切削仿真模型,以45#钢为工件材料,对错齿BTA钻头各刀齿切削不同直径的环状工件进行了模拟仿真,分析了钻削过程中错齿BTA钻头各个刀齿切屑的形成过程与变形特点,研究了环状单元切削力三分量随工件半径的受力分布规律.结果表明,错齿BTA钻头各刀齿切削力分量呈现出随半径增大而增大的非均匀分布规律,并且切削速度和进给量对切削力分布规律几乎没有影响.