高速冲液脉冲放电制备纳米硅球

通过Ansys对单脉冲放电过程进行温度分布仿真时发现,当脉宽很小时,汽化体积所占比例很高,即材料利用率较高,但是产率较低;而加大脉宽时,产率较高,但是汽化比例较低。为综合两者的优势,利用大脉宽加工,使放电通道移动。仿真结果表明,相对于放电通道静止,其在材料利用率和产率上都有了大幅度提高。当在加工中引入高速冲液时,实验表明其能促使放电通道发生漂移,收集产物后称量、计算,其产率达到了1g/h。     

D-region ionospheric disturbances associated with the Extremely Severe Cyclone Fani over North Indian Ocean as observed from two tropical VLF stations

The D-region ionospheric disturbances due to the tropical cyclone Fani over the Indian Ocean have been analysed using Very Low Frequency (VLF) radio communication signals from three transmitters (VTX, NWC and JJI) received at two low latitude stations (Kolkata-CUB and Cooch Behar-CHB). The cyclone Fani formed from a depression on 26th April, 2019 over the Bay of Bengal (Northeastern part of the Indian Ocean) and turned into an extremely severe cyclone with maximum 1-min sustained winds of 250 km/h on 2 May, 2019 which made landfall on 3 May, 2019. Out of six propagation paths, five propagation paths, except the JJI-CHB which was far away from the cyclone track, showed strong perturbations beyond $3\sigma$ level compared to unperturbed signals. Consistent good correlations of VLF signal perturbations with the wind speed and cyclone pressure have been seen for both the receiving stations. Computations of radio signal perturbations at CUB and CHB using the Long Wave Propagation Capability (LWPC) code revealed a Gaussian perturbation in the D-region ionosphere. Analysis of atmospheric temperature at different layers from the NASA’s TIMED satellite revealed a cooling effect near the tropopause and warming effects near the stratopause and upper mesosphere regions on 3 May, 2019. This study shows that the cyclone Fani perturbed the whole atmosphere, from troposphere to ionosphere and the VLF waves responded to the disturbances in the conductivity profiles of the lower ionosphere.     

梳状电容式微加速度计温度性能优化

零偏温度漂移是影响高精度MEMS加速度计整体性能的关键指标，敏感结构机械零位的温度漂移和电路零位(电容检测电路）的温度漂移是加速度计零偏温度漂移的直接原因。分析了影响加速度计零偏温度系数的3种主要影响因素，提出了某型加速度计伺服电路温度性能测试筛选方法，有效减小了电路零位的温度漂移。采用了全硅表头，同时对表头封装粘接方式进行优化，大幅减小了表头机械零位的温度漂移。经过这些优化措施后，加速度计的温度性能得到了明显改善，零偏温度系数由1.3mg/℃减小到0.5mg/℃，零偏的常温稳定性(1h）达到0.108mg，重复性(6次）达到0.141mg。     

Analysis of long-endurance station-keeping flight scenarios for stratospheric airships in the presence of thermal effects

The ability to achieve long-endurance station-keeping flights makes stratospheric airships desirable platforms for the provision of communication and surveillance services. To maintain long-endurance flights, it is necessary to consider the problem of energy consumption. In this paper, we discuss long-endurance flight scenarios of stratospheric airships in the presence of thermal effects. The balance between buoyancy and gravity is influenced by thermal effects during the diurnal cycle. We perform a theoretical analysis based on the helium’s mass, pressure differential, and altitude as the main factors. To verify the effectiveness of the control over the pressure differential and the altitude, three long-endurance flight scenarios are proposed and compared. Then, the corresponding optimization problems are constructed to determine the energy-minimum flight. Finally, further efforts are made to reduce energy consumption. The realization and limitations of two strategies for improvement are analyzed. A comparison with other scenarios shows the effectiveness of energy conservation. The study in this paper thus provides a reference for station-keeping applications of stratospheric airships.     

三角形截面高柔结构横风向振动的风洞试验研究

本文介绍了正三角形截面高柔结构模型在均匀流场和湍流场中三种迎角下的横风向风振响应风洞试验结果，分析了三角形截面高柔结构的横风向涡激振动现象与驰振危险性，获得了一些数据和结论。     

发动机高模试验技术研究

基于ANSYS软件平台,建立了发动机高模试验系统传动轴强度和疲劳数值仿真模型,并进行了数值仿真与分析计算,研究了传动轴强度和疲劳与位移之间的关系,得出了传动轴设计准则.通过对发动机高模试验系统扩压器与氮气破空设备的研究、分析与计算,得出了储能气缸和氮气破空环管的设计准则.采用该设计准则设计的发动机高模试验系统解决了发动机试验启动过程压力过高、回火严重、发动机喷管变形等问题,试验系统满足发动机设计对高模试验的要求.通过该试验系统考核的发动机已成功应用于发射卫星的运载火箭系统.     

激光脉冲圈焊工艺研究与应用

基于有限元软件MSC.MARC软件平台Hypermesh软件模块仿真模拟了激光连续圈焊和激光脉冲圈焊的温度场分布,模拟结果表明:激光脉冲圈焊可有效控制被焊工件温度场分布,焊接热影响区小,为此采用激光脉冲圈焊工艺焊接簧片式电磁阀簧片组件.研究了激光焊接频率与焊点重叠率以及激光焊接速度与焊缝强度和焊点重叠率之间的关系,从而得出了激光脉冲圈焊焊接工艺规范,即激光峰值功率Pf--300 W,激光基值功率Pj=200 W,激光焊接速度v=3.33 mm/s,激光频率f=20 Hz等,采用该焊接规范焊接完成的簧片式电磁阀已经应用于嫦娥五号探测器推进分系统、轨道器子系统以及上升器推进子系统的液体动力装置之中,并已经完成了飞行和月球探测任务.     

异形排气管的热态气动试验

在发动机活动试车台上，对全尺寸的从环形过渡到腰果形的发动机排气量，进行了热态的出口压力和温度分布测试，实验结果表明，排气管出口截面的上部存在有严重的低压区，出现气流倒流的现象，产生的原因是由于发动机排气管的上壁面的扩张角过大造成的，排气管出口夫面温度由上向下不断提高，上部因受冷气倒流的影响，温度只有９０℃左右，而对应排气管环形部分直接排出燃气，由于未受冷空气的掺混，使出口截面下半的气流最调达度４２     

风扇出口导向叶片低噪声设计Ⅰ:方法与优化

作为"风扇出口导向叶片（Outlet Guide Vanes，OGV）低噪声设计"系列文章的第1篇，本文在现有压气机气动设计流程的基础上，加入了噪声评估过程，建立了基于通流设计的气动/声学一体化设计方法。为提高设计阶段的评估速度，以三维升力面理论与管道声学理论为基础，从通流设计和造型设计输出中提取参数，结合转子尾迹模型，建立了转/静干涉噪声的解析预测模型。以现代大涵道比涡扇发动机风扇/增压级为对象，采用该模型系统分析了OGV轴向掠形与周向倾斜对转/静干涉噪声的影响，获取了轴向掠形角与周向倾斜角等三维设计参数与风扇噪声的关系图谱，初步确定了低噪声设计较优降噪量的掠和倾组合方案。以此为基础，在保持叶尖子午投影位置和弦长不变的前提下，将叶片前缘和径向积叠进行参数化，采用遗传算法进一步开展了OGV的低噪声优化设计，最终获得了2个优化方案，预估的降噪量达到了8 dB。     

激光深熔焊接等离子体发射光谱诊断研究

综述了激光等离子体发射光谱诊断的基本假设;介绍了电子温度、密度光谱计算最常用的方法;同时综述了国内外激光焊接等离子体光谱诊断的研究进展.旨在对激光焊接等离子体光谱诊断基本理论和当前的研究进展进行全面的梳理,并对开展激光焊接等离子体光谱试验工作提供理论支持和技术参考.