基于区域平均燃料消耗的推力器配置问题

摘要： 为实现精准的交会对接需要同时进行相对位置与相对姿态的六自由度控制.在控制指令一定的情况下,不同的推力器配置以及不同的控制分配算法会带来不同的推进剂消耗.实际任务中,可以从时间和空间上对控制指令进行划分,即控制指令在一段时间内集中在一定的空间区域内.本文提出发动机配置区域平均燃料消耗的度量指标,针对三维和六维控制任务给出区域平均燃料消耗的计算方法,进而提出对推力器配置阵的优化思路,对于完善控制指令分配和推力器配置设计与优化有重要的意义.     

地面燃气轮机单管燃烧室流量分配试验

对设计的100kW地面燃气轮机单管燃烧室空气流量分配进行了试验研究。在常压环境下采用堵孔法分别得到了旋流器、主燃孔和掺混孔的流量特性曲线,分析得到燃烧室不同结构的流量系数;试验研究了不同进口流量条件下燃烧室的流量分配,测量得到了燃烧室总压损失。研究发现:随着进口空气流量的增加,燃烧室的流量分配比例基本保持稳定,并且与燃烧室的设计空气比例基本吻合;随着燃烧室进口流量（雷诺数）的增加,旋流器、主燃孔和掺混孔的流量系数呈线性降低;随着进口流量（雷诺数）的增加,燃烧室总压损失逐渐增大;对主燃孔和掺混孔的流量特性测量中,两种测量方法得到的试验结果稍有差别,总体上看两种测量方法的试验结果较为接近。通过对比分析证明两种试验测量方法真实可靠,该研究结果可为100kW地面燃气轮机燃烧室的设计与优化提供依据。      

当量油气比对内燃波转子燃烧特性的影响

为了研究当量油气比对内燃波转子燃烧特性的影响规律,采用控制变量法,保持内燃波转子转速、混气填充速度不变,通过调节燃料喷射体积流量改变混气的当量油气比。在不同的当量油气比下开展内燃波转子燃烧特性试验。试验结果表明:当量油气比对于内燃波转子燃烧过程影响很大,随着当量油气比的增加,内燃波转子获得的燃烧压力增益增大,在内燃波转子转速为900r/min、混气填充速度为6.741m/s、当量油气比为1.442时,6个工作循环内平均燃烧压力增益达到246.29％,火焰平均传播速度随当量油气比呈类似正态分布,在化学恰当比附近达到最大10.8m/s。当量油气比小于1时,两组工况下火焰锋面呈向下倾斜状传播,当量油气比大于1时,两组工况下火焰锋面呈向上倾斜状传播。      

液体推进燃料着火特性影响因子与活化能分析

采用反射激波管实验台,对液体推进燃料RP-3着火特性进行了实验研究,并分析了燃料的表观活化能。采用了最大OH-光谱斜率倒推法确定着火终点,判定得到了液体推进燃料的着火特性,并对不同燃料体积分数下的着火延迟进行了归一化处理。结果表明:推进燃料的表观活化能差异不大,约为154～171kJ/mol;对各参数影响因子进行分析,着火延迟时间与当量比成正比关系,与燃料体积分数和混合气压力成反比关系;与JP-10比较发现,着火特性数据受燃料体积分数、当量比的影响因子几乎相等。      

基于LPV状态空间模型的小型航空煤油二冲程发动机喷油控制策略

为了简化基于平均值模型的喷油控制模型的计算,根据线性变参数(LPV)状态空间模型原理,在平均值模型的基础上建立了LPV状态空间喷油控制模型,利用Matlab/Simulink工具对稳态工况和瞬态工况的喷油脉宽控制模型进行仿真,最后在发动机试验台架上进行试验验证.仿真和试验结果表明:①基于LPV状态空间模型的喷油控制模型能够满足瞬态工况和稳态工况控制的要求,计算的喷油脉宽精度略低于平均值模型,由于LPV状态空间模型计算简单,能够直接应用于控制算法的设计,因此在工程中容易实现.②与插值算法相比,基于LPV状态空间模型的控制策略使发动机的动力输出有所下降,主要是由于模型简化造成进气空气流量减小引起的.      

交会对接绕飞段临界安全轨迹研究

以Hill方程为基础对圆轨道近距离双脉冲绕飞安全策略进行研究.首先给出双脉冲绕飞的模型,通过仿真遍历得到不会进入球形安全区的绕飞轨迹,然后绘制出这些安全的绕飞轨迹所对应的绕飞时间、燃料消耗、追踪器与目标器的初始距离三个量之间的关系曲面,进而得到临界安全条件下的关系曲线并拟合出关系表达式,最后对拟合误差进行分析发现导致轨迹偏离的程度很小.     

直升机燃油系统增压转自吸供油动特性

通过某型燃油系统增压供油转自吸供油试验,研究了发动机入口处的流量历程。在试验研究和直升机燃油系统增压转自吸供油机理基础上,利用Flowmaster软件建立了某典型直升机燃油系统仿真模型,仿真结果与试验结果吻合较好,验证了模型的正确性。在此基础上,研究了直升机燃油系统增压转自吸供油动特性。结合仿真结果,分析了增压泵出口单向阀的弹簧预紧力、弹簧刚度对发动机入口燃油流量、压力的影响,为燃油系统零部件选型及参数确定提供参考。     

中点箝位型光伏并网逆变器调制策略及效率对比

传统三电平中点箝位(Three-level neutral point clamped,3L-NPC)半桥逆变器在高压大功率条件下,由于开关器件损耗不均衡而使其容量受限,因此衍生了多种NPC型三电平半桥拓扑。为了优化选取NPC型拓扑及调制策略,对4种3L-NPC型拓扑(二极管NPC、有源式NPC、层叠式NPC及有源层叠式NPC)的调制策略及开关器件损耗分布进行了对比分析,并研制了一台5kW的NPC型统一实验平台,进行了效率测试。理论分析与实验结果表明:(1)根据零电平续流路径的配置不同,NPC型拓扑主要有4种调制策略;(2)选取合理的NPC型拓扑及调制策略,不仅可以均衡器件损耗,而且系统效率基本不变,为逆变器的扩容奠定了基础。     

Numerical investigation of the impact of asymmetric fuel injection on shock train characteristics

Numerical simulations are carried out to investigate the impact of asymmetric fuel injection on shock train characteristics using the commercial-code FLUENT. The asymmetry of fuel injection is examined by changing the fuel flow rates of the upper and lower wall fuel injectors. The numerical approach solves the two-dimensional Reynolds-averaged Navier–Stokes (RANS) equations, supplemented with a k-ω model of turbulence. As a result, different ways of fuel injections will always lead to shock train transitions, with the variations of shock train structure, strength and leading edge position. For symmetric fuel injection, the flowfield of the isolator is quite asymmetric with the boundary layer of the upper wall side developing much stronger than that of the lower wall, which is due to the heterogeneity of the incoming flow. Regarding to asymmetric fuel injection with more of lower wall side, though the pressures in the combustor are nearly the same, the first shock of the shock train converts between ‘Distinct symmetric X type shock’ and ‘Obscure and weaker asymmetric shock’ and the shock train leading edge moves upstream with the increase of the asymmetry level. With regard to asymmetric fuel injection with more of upper wall side, ‘incomplete asymmetric X type shock’ occurs and the shock train structures keep nearly the same with low level of fuel injection asymmetry. Unexpected results like unstart will happen when increasing the level of fuel injection asymmetry. And the isolator will come back to normal state by decreasing the differential of upper and lower wall sides fuel injections.     

Experimental study of a flush wall scramjet combustor equipped with strut/wall fuel injection

In this study a flush wall scramjet combustor is tested in a supersonic incoming air flow with the Mach number of 3 which is generated by an air vitiation heater producing the stagnation temperature of 1505 K. Using liquid kerosene as the fuel, the flame is stabilized by means of a centrally mounted O₂ pilot strut after being ignited by a plasma torch. During experimental measurements, the fuel is injected with a constant equivalence ratio of 0.8 according to specified strut/wall injection ratios, i.e., a portion of the fuel amount is injected from the strut while the rest is injected from the wall. The strut and wall injectors are arranged at the same axial position. The combustion performance and wall temperature gradients are evaluated with various fuel feeding ratios between the wall and the strut. Experimental results show, when the equivalence ratio is constant and the axial injection position is fixed, the combustion characteristics vary significantly with the strut/wall fuel feeding ratio, especially when this ratio is close to its lowest and highest limits. Among the four fuel feeding ratios examined, the strut only injection mode and the average distributed strut/wall injection mode show the best combustion performance. However, the strut/wall injection mode produces a smaller wall temperature gradient compared to the strut only injection mode, which is due to the significant film cooling effect caused by the wall injected liquid kerosene.