离心条件下后台阶贫油熄火特性

利用气流通过弯管产生的离心效应来模拟高速旋转的工况,研究高位后台阶火焰稳定器的关键几何参数对液雾燃烧贫油熄火特性的影响.通过控制后台阶高度,台阶板长度,后台阶到上壁面的距离三个几何参数,考察它们对后台阶火焰稳定器贫油熄火特性的影响.试验得到的结果表明在离心条件下,后台阶高度和台阶板长度对贫油熄火特性的影响较大,随着后台...     

ARC-MET930测定铝合金中的金属元素

应用芬兰ARC-MET930金属分析仪,制作万能校准曲线,测定铝合金中的金属元素含量,优化了分析条件,讨论了分析结果的精密度和准确度。本方法具有准确度较高,成本低,分析快,操作简便,激发试样次数少等优点,用于快速定量分析,现场分析牌号,取得了满意的效果。     

Development of microstructural inhomogeneity in multi-pass flow forming of TA15 alloy cylindrical parts

Revealing the development of microstructural inhomogeneity in the multi-pass flow forming of titanium alloy components is of great significance to the microstructure control and property tailoring. To this end, the microstructural inhomogeneity of TA15 alloy spun cylindrical parts was analyzed based on the deformation history. The results indicate that the material underwent significant compressive strain in the normal direction (ND), tension strain in the rolling and circumferential directions (RD and CD), while tension strain in the CD is slightly small due to the limited material flow in this direction. These strain characteristics make the microstructure, especially the primary α (α_p), present different morphologies in the different planes of the part. Meanwhile, the combined effects of inhomogeneous deformation and temperature distribution in the ND also cause the inhomogeneity of microstructure morphology and parameters in this direction. Quantitative analyses show that with the forming pass increasing, the aspect ratio of α_p increases most in the normal-rolling plane, then in the normal-circumferential plane and least in the circumferential-rolling plane, whereas α_p content decreases in an opposite trend. Along the ND, the aspect ratio and content of α_p is relatively high in the outer and inner surface areas but lowest in the central area, and these inhomogeneous characteristics can be gradually diminished with the forming pass increasing. Furthermore, the variation of hardness inhomogeneity factor indicates that a four-pass forming with the total reduction ratio of 63% could obtain a homogenous microstructure along the ND of the TA15 alloy spun cylindrical part.     

四种风洞收缩段流场特性对比

基于西北工业大学高亚声速平面叶栅风洞,测量了维氏收缩段的出口流场,发现其方向场品质较差,相比速度场和总压场,核心区沿周向减小了15%。对四种收缩段进行数值模拟后,对比了收缩段的出口核心区、均匀性及分离特性,发现维氏曲线在前部收缩,进口收缩过急引起旋涡,但出口稳流段较长,因此出口均匀性更好。双三次曲线在后部收缩,主流区顺压梯度更大,因此附面层更薄,气流偏角更小,分离特性更好,但出口过冲更大。现有维氏收缩段的三维结构在拓宽核心区同时对气流扰动较大,恶化速度场与方向场,气流偏角增加最大达43%。进口管径对双三次收缩段的流场特性影响不大。     

电位法测量微缺口试样的数值分析

疲劳寿命受到材料内部缺陷的制约,可以通过电位法试验获得微缺口试样的疲劳裂纹扩展规律,进而分析缺陷对材料疲劳寿命的影响。在试验前,需要预先研究试验的主要影响因素。利用COMSOL有限元软件,研究了电流输入点位置和电势差测点位置对试验精度和试验复现性的影响,计算得到不同裂纹前缘形状对应的电位法校核曲线。结果表明:(1)电流输入点位置位于试样平行于裂纹面的上下表面时,可以保证试验的复现性。(2)当测点位于裂纹面的垂直对称面上,且测点距离裂纹面垂直距离为0.06～0.1倍试样宽度时,可以同时满足测试精度和复现性。(3)当裂纹宽度和裂纹深度的比值3时,可以不考虑裂纹前缘形状对校核曲线的影响,当裂纹宽度和裂纹深度的比值≤3时,裂纹前缘形状对校核曲线的影响较大。     

提高航空发动机性能的弯扭导向器技术

给出了采用弯扭导向器提高发动机性能的设计原则：在全三维弯扭设计时，必须在保证涡轮前总温、总压和燃气流量的前提下，合理调整尾喷管面积，提高涡轮后背压，保证在设计转速下涡轮输出功与原型涡轮级相同，从而保证了压气机的设计点和喘振裕度，同时提高了发动机推力、降低油耗。     

一种基于计算几何控制无量纲参数的叶片造型方法

应用目前先进的自由曲线理论,开发了一种新的叶片造型方法——B样条控制中线角叶型(BMAA)方法。分别选取准均匀B样条和贝塞尔曲线,实现了对叶型中线和厚度的方便、灵活控制;同时综合考虑方便性与实用性,选取四点控制参数进行设计。分别利用BMAA方法与原有定制叶型、任意中线方法,对某单级压气机进行设计,结果表明:对于超/跨声叶片设计,BMAA方法设计的叶片性能略优于定制叶型;与任意中线叶型达到的性能相当,但叶型控制便捷性和叶型光滑性优于任意中线叶型。     

基于ADRC的航空发动机限制保护器设计

发动机限制保护器在航空发动机运行过程中对特定的被限制量进行实时监控,在其超出安全范围时实施限制,实现对航空发动机的保护.将自抗扰技术用于限制保护控制器设计,利用自抗扰控制器的扩张观测器,动态估计未知扰动和系统特性,对实际控制量进行反馈补偿,实现超限后的快速保护,提高了发动机的安全性.仿真结果表明:所设计的自抗扰限制保护控制器能将超限偏差有效转化为对主回路指令的修正,综合控制系统响应速度快,达到了限制保护的目的.     

Shape and motion estimate of LEO debris using light curves

We have derived a tri-axial ellipsoidal model of an LEO object, a Cosmos 2082 rocket body, including its rotational axis direction, rotation period, precession, and a compositional parameter, using only light curve data from an optical telescope. The brightness of the object was monitored for two days and least-squares fitting was used to determine these values. The derived axial ratios are 100:18:18, the coordinates of the rotational axis direction on the celestial sphere are R.A. = 305.8° and Dec. = 2.6°, and its observed average rotation period is 41 s. When precession is considered, its amplitude and precession period are 30.5° and 29.4 min. These results show that optical light curve data are sufficient to determine the shapes and the motions of LEO objects.     

人体变形中局部坐标系旋转失真问题

分析了人体变形中选取3个基轴构建坐标系所存在的缺陷,提出了一种位置-四元数的方法,解决了曲线骨架驱动的旋转失真现象.采用四元数球面线形插值和B样条四元数插值的方法构建人体变形中曲线骨架的局部坐标系,采用位置-四元数-缩放的方式代替传统的转化矩阵,通过人体表面顶点在该坐标系下的绑定,实现人体皮肤、肌肉的变形.试验结果显示:该方法有效地消除了局部坐标系的旋转失真现象,适用限制少,易于实现.