关于螺旋桨桨叶有利迎角的探讨

通过桨叶的性质角与迎角关系的数学模型,对桨叶有利迎角进行了分析研究。当桨叶迎角和桨叶性质角变化时,桨叶极线图和桨叶总空气动力向拉力轴靠近或离开,由此找出桨叶的最有利状态。通过分析得出,桨叶迎角接近桨叶临界迎角时最有利。最后通过桨叶极线图和桨叶总空气动力方向变化的模型实验验证了此结论的正确性。     

带限位台阶的高阻尼橡胶减振器性能试验分析

航天工程中的有害振动可通过高阻尼橡胶减振器进行控制,但核心耗能单元和其他部件之间的连接容易失效。为了改进高阻尼橡胶减振器中阻尼材料和钢板的连接模式,使两者在较大变形下具有较高的机械连接性能,并且避免采用高温高压整体硫化的生产工艺,提出了一种带限位台阶的装配式高阻尼橡胶减振器。该减振器的阻尼材料和钢板之间采用常温胶黏连接模式,且在阻尼材料和钢板的连接边界面上设置了若干个具有一定高度的阶梯状限位台阶。对限位阶梯总高度分别为3 mm、4 mm、5 mm的3种不同装配式高阻尼橡胶减振器进行了不同加载频率和幅值的性能试验。试验结果表明:新型装配式高阻尼橡胶减振器在大变形下具有较强的耗能能力。带限位台阶的减振器和没有限位台阶的减振器相比,最大储能模量提高了22.3%,损耗因子提高了24.9%,且在较大位移幅值工况下,滞回曲线由原本的椭圆形变成类8字型,在保证较高阻尼力的同时使得滞回曲线所包络的面积增大,最大增幅可达588%。该新型减振器无需高温高压整体硫化,可以显著降低生产成本并提高生产效率,具有显著的性能优势和广泛的应用前景。     

起落架缓冲器静压曲线符合性偏差问题分析

依据起落架缓冲器静压缩曲线图对确保飞机起落架质量的重要性,对绘制起落架静压缩曲线图时出现的符合性偏差问题进行了分析,并提出了相应工艺措施。     

Dual Drive Curve Tool Path Planning Method for 5-axis NC Machining of Sculptured Surfaces

The problem of finished surface being not first-order continuous commonly exists in machining sculptured surfaces with a torus cutter and some other types of cutters. To solve this problem, a dual drive curve tool path planning method is proposed in this article. First, the maximum machining strip width of a whole tool path can be obtained through optimizing each tool position with multi-point machining (MPM) method. Second, two drive curves are then determined according to the obtained maximum machining strip width. Finally, the tool is positioned once more along the dual drive curve under the condition of tool path smoothness. A computer simulation and cutting experiments are carried out to testify the performance of the new method. The machined surface is measured with a coordinate measuring machine (CMM) to examine the machining quality. The results obtained show that this method can effectively eliminate sharp scallops between adjacent tool paths, keep tool paths smooth, and improve the surface machining quality as well as machining efficiency.     

Hybrid method based on flame volume concept for lean blowout limits prediction of aero engine combustors

The Lean Blowout (LBO) limit is crucial for the aircraft engines. The semi-empirical (such as Lefebvre’s LBO model and Flame Volume (FV) model), numerical and hybrid methods are widely utilized for the LBO limit quick prediction. An innovative hybrid method based on the FV concept is proposed. This method can be classified as a semi-empirical/physical based hybrid prediction method. In this hybrid method, it is assumed that the flame volume varies nearly linearly with the fuel/air ratio near the LBO. The flame volume is obtained directly by the numerical simulation using the threshold value of the visible flame boundary as 900 K. Then the final LBO limits is determined by the FV model. On the premise of keeping the good generality of prediction, the hybrid method based on the FV concept can further improve the prediction accuracy. The comparison with the prediction of the existing available methods on fifteen combustors shows that the hybrid method based on the FV concept achieves better prediction accuracy. The prediction uncertainties between the experimental results and the predicted values by the hybrid method based on the FV concept are within about ±10%.     

基于载波相位的多通道相位一致性测量方法CSCD

对于卫星导航系统,由导航天线进行波束合成的多路并行导航信号需要具有严格的相位一致性,本文给出基于专用地检设备的多通道相位一致性测量方法。该地检设备采用载波相位辅助伪码测距技术,通过载波相位和伪码相位的联合解算,实现了伪码相位对载波相位解整周期模糊,最终测距精度达到1ps。采用该测试方法对系统进行配相,实现了各通道无周期模糊的相位一致性。     

燃气轮机仿真中部件特性处理方法的准确性研究

在基于部件的燃气轮机性能仿真建模过程中,部件特性线处理方法的准确性是影响整个机组仿真精度的关键因素。分别介绍了采用传统离散插值处理方法、人工神经网络法和偏最小二乘法进行部件特性线处理的原理和方法,利用一部分已知样本特性数据和不同处理方法对某燃气轮机进行性能仿真,并将仿真结果与另一部分已知样本特性数据进行比较,分析不同处理方法对部件特性和整机性能计算精度的影响。结果表明:在仿真过程中利用偏最小二乘法可直接使用重构方程求解部件特性,无需对部件特性离散化和插值处理,避免了传统部件特性处理方法的计算误差,提高了燃气轮机热力模型求解的精度。     

旋转调制光纤陀螺惯导寻北精度探索

高精度寻北是旋转调制光纤陀螺惯导实现高精度导航的前提,也是其技术优势的体现。针对当前旋转调制光纤陀螺惯导在快速高精度寻北中遇到的问题,对其寻北精度极限进行了深入研究,梳理出4项最主要的影响因素,对其影响机理、误差模型、量级进行了深入的分析,并通过样机试验进行了验证。结果表明,尽管随机游走系数是制约寻北精度极限的最终因素,但陀螺刻度系数误差、扰动速度、航向效应等误差处理不好,将严重影响旋转调制寻北精度;通过采取措施,高精度光纤陀螺旋转调制惯导5min寻北精度已达到35″(3σ),进一步提高精度的措施正在研究中。     

汽车单叶片真空泵设计中的最优椭圆曲线

单叶片真空泵的设计主要是确定泵体内腔曲面,使同时作旋转运动和径向滑动的叶片的圆柱形端面和它保持相切。泵体内腔曲面的投影必须是一条封闭的光滑曲线。设计时,这条光滑曲线的一部分通常被提前选定,而剩余部分则根据几何约束产生。尽管一般的椭圆曲线可以满足参考曲线和生成曲线在连接点一阶可导,但在连接点通常是二阶不连续的。将找出一条最优的椭圆参考曲线,使得泵腔形线在连接点处不仅是一阶连续的而且是二阶连续的。这将使得泵的运转更加平稳并减小由于叶片径向加速度不连续产生的振动和噪声。