超声速流中激波/湍流附面层干扰数值模拟

采用修正的B／L湍流模型以及多块结构化网格求解了二维N-S方程。分别对超声速流和高超声速流中的激波／湍流附面层干扰进行了数值研究。本文首先研究了进口马赫数为2．96的超声速流。计算结果准确预测了入射斜激波在平直壁面引起湍流附面层分离的流动特征：分离点的反射激波、分离包引起的膨胀扇以及再附点的反射激波。计算的壁面压力分布与实验值吻合较好，计算的分离区长度与实验值比较有一定误差。本文还对进口马赫数为9．22的高超声速流中压缩角引起的激波／湍流附面层干扰进行了数值研究。计算结果与实验结果吻合较好。     

深层搅拌法技术及其工程应用

深层搅拌技术是对软土地基进行处理的较常用技术 ,它具有加固效果显著、形式灵活多样、环境无污染、施工机具简单、施工速度快、节省投资等优点 ,目前在地基处理和基坑工程中广泛采用。本文主要阐述该技术特点及在地基处理工程中的应用 ,对同类工程设计具有重要的参考价值。     

冗余度机器人力控制的运动学稳定性分析

把非冗余度机器人位置／力混合控制方案引入到冗余度机器人，用线性化的动力学模型对其运动学稳定性进行分析，提出一种改进的基于运动学稳定的冗余度机器人混合控制策略。仿真研究结果证明了所提出方法的有效性。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

蜂窝式轴心通风器油气分离性能计算

为对航空发动机蜂窝式轴心通风器油气分离效率进行研究,建立考虑油气双向耦合的流场计算方法及油滴/壁面相互作用模型,在验证通风阻力及油气分离效率可靠性的基础上,对不同转速、通风流量和环境温度下蜂窝式轴心通风器的油气分离效果进行计算和分析.结果表明:转速的增加会使油气分离效率得到提升,而通风流量和环境温度的增加则导致油气分离效率的降低.蜂窝孔结构的加入对通风阻力影响不大,却对通风器的滑油分离过程起主要作用,计算表明其对滑油分离贡献率在80%以上.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。     

展向振荡对激波/湍流边界层干扰的影响

周期振荡作为一种有效的壁面流动控制手段受到广泛关注,而其对激波/湍流边界层干扰的影响目前鲜有研究。本文采用高精度直接数值模拟（DNS）方法对马赫数2.9、12°激波入射角、强振荡下的激波/湍流边界层干扰进行了系统研究。通过与无振荡工况的定量比较,揭示了展向强振荡对干扰区内复杂流动结构的影响规律及作用机制,如分离泡尺度、物面压力脉动非定常特性、物面剪切的非定常特性及统计特征等。研究发现：在展向强振荡作用下,分离点位置提前,间歇区长度增大;同时由于分离泡内强黏性耗散的影响,展向振荡的穿透高度约为分离泡高度的4%,因而对流动结构不会产生实质影响。但展向强振荡会对壁面附近流动造成显著影响,如强振荡诱导的壁面展向速度远大于流向速度,造成流向剪切与展向剪切之间夹角的概率密度函数峰值从0°偏移到80°~90°之间。物面压力及剪切本征正交分解分析表明,展向振荡会导致模态能量从低阶模态向高阶模态转移,降低低频运动的能量占比,增强再附后Görtler涡等壁面附近旋涡结构的强度。     

流场可压缩性对涡相互作用影响的数值研究

涡相互作用作为冲压发动机喷注装置的典型抽象流动现象,研究其可压缩性影响对于认识包含化学反应的真实燃料喷射场具有一定基础理论价值。基于经过数值验证的可压缩Navier-Stokes算法与压力泊松方程初始条件设置方法研究流场可压缩性对涡相互作用演化过程的影响。结果表明,以较高涡旋马赫数表征的可压缩性在改变涡对形态的同时,具有延缓涡旋相互靠近,迟滞融合进程的作用。关于涡对系统开始融合的临界条件,可压缩相互作用开始的临界展弦比与无量纲时间相比于低速涡对明显提高。为在无量纲时间意义下统一不同马赫数涡对相互作用的进程,从涡心密度随时间变化规律出发在不可压涡对特征时间的基础上,初步构建了考虑可压缩性的时间尺度修正关系。