Simultaneous state and actuator fault estimation for satellite attitude control systems

In this paper, a new nonlinear augmented observer is proposed and applied to satellite attitude control systems. The observer can estimate system state and actuator fault simultaneously. It can enhance the performances of rapidly-varying faults estimation. Only original system matrices are adopted in the parameter design. The considered faults can be unbounded, and the proposed augmented observer can estimate a large class of faults. Systems without disturbances and the fault whose finite times derivatives are zero piecewise are initially considered, followed by a discussion of a general situation where the system is subject to disturbances and the finite times derivatives of the faults are not null but bounded. For the considered nonlinear system, convergence conditions of the observer are provided and the stability analysis is performed using Lyapunov direct method. Then a feasible algorithm is explored to compute the observer parameters using linear matrix inequalities (LMIs). Finally, the effectiveness of the proposed approach is illustrated by considering an example of a closed-loop satellite attitude control system. The simulation results show satisfactory perfor-mance in estimating states and actuator faults. It also shows that multiple faults can be estimated successfully.     

个性化自适应课件生成器的研究

分析基于Internet的远程教育学习站点存在两个明显的缺点,提出个性化自适应课件生成器的概念,并针对其关键技术问题进行研究与讨论。     

基于自定义组件的故障诊断过程显示

针对导弹控制系统结构复杂,信号线繁多,难以在故障诊断软件设计中实现诊断过程图形化实时显示的问题,提出了一种基于自定义组件开发故障诊断软件的方法.根据导弹控制系统的故障诊断流程及实时显示需要,对其结构进行了分析,抽象出了主要组成元素--信号通道和部件,由此提出了需要定义的相应组件.用Borland C Builder6.0开发环境进行了应用实践,证明使用这种方法可快速开发出能图形化实时显示故障诊断过程的导弹控制系统故障诊断软件,开发出的软件还具有运行稳定、修改升级方便等优点.     

一种基于Deep-GBM的航空发动机中介轴承故障诊断方法

针对航空发动机中介轴承故障信号难于识别的特点,提出了一种深度梯度提升模型（Deep-GBM）对振动信号特征进行逐层学习以提高分类模型的准确率。开展某型航空发动机中介轴承故障模拟实验,并采用经验模式分解(EMD)方法对采集的振动信号进行分解,提取内蕴模式函数(IMF)分量非线性动力学参数样本熵作为原始故障特征。采用Deep-GBM对中介轴承内环故障、内环和滚动体综合故障、正常、滚棒剥落、滚棒划伤五种不同状态进行识别。实验结果表明,所提出的Deep-GBM故障诊断准确率达到87%,相对于传统的机器学习模型准确率最高提升了28%,并具有良好的泛化能力。      

基于卷积门控循环网络的滚动轴承故障诊断

针对许多基于深度学习的滚动轴承故障诊断方法在小样本数据集下诊断性能下降的问题,提出一种基于卷积门控循环神经网络的轴承故障诊断模型。该模型使用两层的卷积网络来从输入信号中提取特征,同时使用tanh函数作为激活函数,且池化层使用大池化核来进行重叠下采样。将所提取得到的高层特征连接到双向门控循环网络。合并循环网络正向和逆向的最后一个状态,并连接一层全连接层进行输出。选用凯斯西储大学的轴承故障数据集来验证模型在小样本数据集下的诊断性能,实验结果表明,相比于其他类型的模型,该模型在仅有20个训练样本的情况下依然保持97%的识别准确率。      

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

考虑外圈局部缺陷的滚动轴承非线性动力特性

 建立了考虑滚动轴承外圈局部缺陷、非线性轴承力和径向游隙等非线性因素的滚动轴承系统动力学微分方程,并用Runge-Kutta-Felhberg算法对其求解。利用分岔图、Poincaré映射图、频谱图以及均方值、峰值因子、峭度等时域参数,分析了滚动轴承的响应、分岔和混沌等非线性动力特性。结果表明：考虑外圈局部缺陷的滚动轴承系统存在多种周期、拟周期和混沌响应;滚动轴承系统进入混沌的主要途径是倍周期分叉;峰值因子比率在中、低速,峭度比率在低速时可以很好地识别外圈局部缺陷。均方值比率除了在与轴承动力特性有关的个别转速外,可以在较大的转速范围识别外圈局部缺陷。     

一种基于正弦图的工业CT系统转台旋转中心自动确定方法

构建一个工业CT成像系统,转台旋转中心的确定是非常关键的步骤,其定位误差会引起CT图像上的伪影。本文在详细分析了现存旋转中心确定方法不足的基础上,提出了一种新方法,该方法利用隐含在正弦图中的对称投影信息,并根据经过旋转中心的射线束在两个对称投影视角下透过的物体路径相同这一规律来定位旋转中心。相对现有算法,该方法适用于射线源与旋转中心的连线不严格垂直于探测器的情形,无需使用模体,亦无需知晓任何几何参数,实时且基本不受随机噪声影响。实验数据验证了该方法的有效性。     

镍基单晶合金蠕变研究:试验、机理及材料模型

在镍基单晶合金高温蠕变建模研究工作的第一部分,通过对DD6镍基单晶合金不同中断时间的高温蠕变试验及透射电镜(TEM)观察,结合单晶合金蠕变机理的研究成果阐明了单晶高温蠕变的机理,并从Orowan方程出发,在晶体塑性理论框架下建立描述晶体滑移系上位错演化规律的方程,发展了以位错密度变化表征镍基单晶高温蠕变的材料模型.该模型考虑了较宽温度与载荷范围内单晶的主要蠕变机理,可较好地建模750～1100℃范围内镍基单晶的各向异性蠕变行为.      

发动机试车气路故障诊断系统的设计与应用

以发动机整机试验数据为研究对象,建立了一套发动机试车气路故障诊断系统.首先阐述了该系统的设计功能和总体流程逻辑;使用故障模式法和调整模式法建立了气路部件故障诊断和优化调整模块;然后以一个双轴分排涡扇发动机为例,针对气路部件故障诊断和优化调整给出了考虑噪声的数值试验分析.最后就该系统的发展进行了讨论.