高空环境下喷嘴参数对航空活塞发动机燃烧与性能的影响

以一台四缸四冲程压燃式航空煤油活塞发动机为研究机型,运用工程系统高级建模和仿真平台软件(AMESim)仿真软件建立了发动机的整机模型,并使用台架实验的采集数据对该仿真模型进行了验证。在高空环境中,仿真分析了飞行器起飞工况、最大巡航工况下发动机喷油器的不同喷孔数、孔径对发动机燃烧过程、性能和NOx排放特性的影响。计算结果表明:稳态工况下,随着喷孔数的增加,最高燃烧压力和温度增加,瞬时放热率增长速度快且峰值上升;同时,缸内预混燃烧得到强化,燃烧始点提前,滞燃期和燃烧持续期缩短,燃烧重心前移,循环热效率增高,但同时会提高NOx的生成量;在飞行器瞬态变海拔的起飞工况下,多喷孔数、小孔径的喷油嘴有利于航空活塞发动机在高空环境下恢复发动机功率,提升飞行器的动力性和续航性能。      

Influence of leading edge with real manufacturing error on aerodynamic performance of high subsonic compressor cascades

To investigate the influence of real leading-edge manufacturing error on aerodynamic performance of high subsonic compressor blades, a family of leading-edge manufacturing error data were obtained from measured compressor cascades. Considering the limited samples, the leading-edge angle and leading-edge radius distribution forms were evaluated by Shapiro-Wilk test and quantile–quantile plot. Their statistical characteristics provided can be introduced to later related researches. The parameterization design method B-spline and Bezier are adopted to create geometry models with manufacturing error based on leading-edge angle and leading-edge radius. The influence of real manufacturing error is quantified and analyzed by self-developed non-intrusive polynomial chaos and Sobol’ indices. The mechanism of leading-edge manufacturing error on aerodynamic performance is discussed. The results show that the total pressure loss coefficient is sensitive to the leading-edge manufacturing error compared with the static pressure ratio, especially at high incidence. Specifically, manufacturing error of the leading edge will influence the local flow acceleration and subsequently cause fluctuation of the downstream flow. The aerodynamic performance is sensitive to the manufacturing error of leading-edge radius at the design and negative incidences, while it is sensitive to the manufacturing error of leading-edge angle under the operation conditions with high incidences.     

轴向间距对压气机通道堵塞及总性能的影响

为了研究转静子叶片排之间的轴向间距对压气机内部流动堵塞及气动性能的影响,选取某单级轴流压气机为研究对象,采用多通道非定常数值计算方法对其5种不同轴向间距下的内部流场进行了全三维数值模拟。结果表明:在每一种轴向间距下,当压气机节流至某一工况之后,压气机通道内的流动堵塞区主要集中在转子叶顶间隙区域和动叶吸力面尾缘附近以及静叶吸力面轮毂角区内;在同一流量下,随着轴向间距的减小,转子叶根吸力面尾缘处的流动堵塞区有所扩大,但转子叶顶间隙区域及静叶吸力面轮毂角区内的流动堵塞区体积却不断减小,压气机通道内回流区的总体积也随之减小,其结果是压气机的静压升能力和流动稳定性增强且效率增大。通过进一步研究发现:在同一流量下,当轴向间距减小时,转子叶顶间隙区域内的主流轴向动量增大且泄漏流的轴向动量减小,其结果是转子叶顶间隙区域内流动堵塞区的体积减小。     

Flow field characteristics,mixing and emissions performance of a lab-scale rich-quench-lean trapped-vortex combustor utilizing a quench orifice plate combined with a bluff-body

In this study, the low emission combustion technology of Rich-Quench-Lean (RQL) has been applied in Trapped-Vortex Combustor (TVC), and the combinative RQL-TVC shows a promising low emissions performance. By utilizing a quench orifice plate combined with a bluff-body, a lab-scale RQL-TVC was designed. The flow fields of RQL-TVC were measured by 2-D PIV and predicted by 3-D numerical simulation. Flow structures, radial profiles of normalized mean axial velocity, turbulence intensity and mixing level of the quench zone were analyzed. Results reveal that the dual-vortex and the single-vortex flow patterns both exist in cavities and quench zone of RQL-TVC, and the turbulence intensity is strong in the quench zone with some reverse flows. The spiral vortex was discussed by 3-D streamlines and the detail flow structures of the quench zone were analyzed based on the numerical results. The mixing level of the quench zone was determined, and results show that the quench device enhances the mixing level compared with TVC. Combustion efficiency and emissions performance were investigated experimentally, and results demonstrate that RQL-TVC has relatively higher combustion efficiency and lower emission index of CO, UHC and NO_x than the same size lab-scale TVC in present work.     

激波引燃冲压发动机一体化流场数值模拟

激波引燃冲压发动机是一种采用爆轰形式组织燃烧的吸气式高超声速飞行器动力系统。采用AUSMPW+迎风格式、氢氧7组分8步基于反应模型,在非结构网格离散域上求解二维多组分化学非平衡流Euler方程。采用发展的数值方法求解了激波引燃冲压发动机内外一体化流场,研究了台阶长度、斜劈尖角度对发动机流场结构和发动机性能参数的影响规律。计算结果表明,所发展的数值方法能用于激波引燃冲压发动机的一体化流场和性能预示计算;台阶长度和斜劈尖角度影响发动机流场结构和预混气体能量释放程度。推力和燃料比冲均随台阶长度的增大而增大,随斜劈尖角度的增大而减少。     

航天器多继电器线圈并联电路的可靠性研究

航天器配电系统中广泛采用多继电器线圈并联电路作为平台设备和负载的供电通路开关。文章从继电器互感效应入手,对多继电器线圈并联电路在指令发出、指令结束2 种工况下的电路可靠性进行了分析,结果表明目前常用的继电器线圈并联电路存在可靠性隐患。因此,针对隐患提出了在继电器线圈前串接二极管的电路可靠性优化方案。试验结果表明,优化后的电路形式可以有效提高电路的可靠性。     

基于模糊集理论的航空四站装备综合性能评价研究

利用模糊综合评价的原理,在考虑四站装备的各种性能指标和装备综合性能的基础上,建立四站装备的综合评价数学模型,得出四站装备综合评价值,追求航空四站装备综合效益,为科学评价四站装备综合性能提供理论依据。     

对某型航空发动机参数的调整分析

分析某型发动机部件对有关性能参数的影响和调整机理,针对因部件效率下降较多引起的性能参数不能同时符合技术要求的问题进行分析,提出适当减小喷管喉部截面面积最小液压限制值来进行调节,使之符合技术要求。     

一种新的加权最小二乘支持向量回归机及其对性能退化航空发动机推力估计的应用(英文)

要实现航空发动机的性能退化缓解控制,需要设计一个高精度并具有良好实时性的推力估计器。针对这种需要,本文提出了一种新的加权最小二乘支持向量回归机,并在此基础上设计了性能退化推力估计器。和现有的加权策略相比较,基于此新的加权策略的推力估计器不仅能满足性能退化缓解控制对精度的要求也能满足实时性的要求。最后,仿真实验证明此加权最小二乘支持向量回归机以及基于此回归机设计的推力估计器的有效性和可行性。     

富氢/富氧燃气同轴双剪切气-气喷嘴性能仿真分析

为研究富氢/富氧燃气同轴双剪切气-气喷嘴设计参数对燃烧性能和燃烧室热载的影响,采用正交试验设计方法对这些参数进行组合,数值模拟单喷嘴燃烧室流场,并以燃烧长度、燃烧室壁面和喷注面板处平均燃气温度为指标评价燃烧性能和热载.结果表明:燃氧速度比对燃烧性能和燃烧室热载影响最显著,中心氢流量比例对燃烧室热载影响非常显著,氧压降比对喷注面板处燃气平均温度的影响也很显著,而喷嘴出口壁厚对喷嘴性能影响不明显.燃氧速度比和氧压降比的交互作用对喷嘴性能有一定影响,而其他设计参数之间的交互作用对喷嘴性能影响非常小.最短燃烧室长度为117.9mm,最低壁面燃气温度及面板燃气温度分别为1637.7K和806.6K.