Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

长板件数控加工技术的探索与研究

结合某型机板件在数控加工中的研制生产状况和存在的问题,论述了实现各种长板件类结构零件装夹定位、刀具及其参数、加工方案及程编策略.通过这些技术措施的实施,在一定程度上解决了在加工长板类零件装夹和定位时出现的零件变形、让刀效率低、质量不稳定等问题.     

民机制造环节的重量控制和减重措施研究

重量控制贯穿民用飞机从设计、制造到运营的全生命周期。尽管飞机重量的决定性因素主要在设计环节,但从国内外飞机制造商的经验来看,在飞机量产阶段仍有优化的余地。对国内外飞机制造商在飞机制造环节的减重经验进行总结,并重点阐述波音公司在制造过程中的重量预警项目（Manufacturing Weight Awareness Process,简称MWAP）,以期有所启发。     

液化天然气作为航空燃料的发展趋势及特点分析

为研究液化天然气(LNG)作为航空燃料的可行性,对LNG的特点、发展趋势及作为航空燃料存在的问题进行了分析.采用了横向比较的方法,将LNG与新的航空替代燃料和传统航空燃料进行了比较和计算分析.结果表明:与新的航空替代燃料相比,LNG具有来源广泛、经济性好、发动机适应性强等优点.与传统航空燃料相比,LNG的储量大,可使用100年以上;可燃极限宽、污染物排放低,NOx排放仅为航空煤油的1/4;单位质量能量密度高、成本低,其燃料成本仅为航空汽油的一半,航空煤油的1/3;同时还具有可用于发动机高温部件冷却用的冷能,是一种极富潜力的航空燃料.指出在LNG作为航空燃料方面急需开展动力系统与飞机结构的匹配、燃料相态的有效转化及不同燃料在燃烧室内的反应特性等方面的研究工作.      

负游隙对高速高温薄壁圆柱滚子轴承动态性能的影响分析

计算了圆柱滚子轴承径向游隙为负值时的等效径向预紧载荷,并考虑等效径向预紧载荷下的套圈弹性变形,通过求解包含套圈弹性变形接触变形等效径向预紧载荷的非线性方程组,得到负游隙圆柱滚子轴承内部的载荷分布情况,以及负径向游隙带来的套圈周向应力.以此分析了负游隙对轴承承载性能及疲劳寿命的影响.结果表明:负径向游隙能够有效降低轴承打滑率,但同时也会降低轴承疲劳寿命,因此在负游隙设计时需同时考虑打滑率和轴承寿命,选择恰当的负游隙.     

平箔片楔形高度对气体止推箔片轴承特性影响

针对波箔型气体止推箔片轴承,建立了箔片结构二维薄板模型,并通过有限差分法和有限元法耦合求解可压缩气体Reynolds方程和气膜厚度方程,获得了给定轴承载荷条件下轴承气膜压力分布、气膜厚度分布、平箔片变形量和功率损耗等轴承特性.通过对比楔形高度分别为25,70,100,200,300μm时的轴承特性仿真结果研究了楔形高度对轴承性能的影响.结果表明:降低楔形高度使轴承气膜压力分布更均匀,并降低了平箔片的局部集中载荷.但楔形高度存在一个最佳值,使得达到相同轴承载荷所需的最小气膜厚度最大,并且轴承具有最小功率损耗,提高了轴承的工作效率.该结果为气体止推箔片轴承的结构设计提供的理论参考.      

Advances and trends in plastic forming technologies for welded tubes

With the implementation of environmental protection, sustainable development and conservation-oriented policies, components and parts of thin-walled welded tubes have gained increasing application in the aircraft and automotive industries because of their advantages: easily achieving forming and manufacturing process at low cost and in a short time. The current research on welded tube plastic forming is mainly concentrated on tube internal high-pressure forming, tube bending forming, and tube spinning forming. The focuses are on the material properties and characterization of welded tubes, finite element modeling for welded tube forming, and inhomogeneous deformation behavior and the mechanism and rules of deformation coordination in welded tube plastic forming. This paper summarizes the research progress in welded tube plastic forming from these aspects. Finally, with a focus on the urgent demand of the aviation, aerospace and automotive industries for high-strength and light-weight tubes, this paper discusses the development trends and challenges in the theory and technology of welded tube plastic forming in the future. Among them,laser tailor-welded technology will find application in the manufacture of high-strength steel tubes.Tube-end forming technology, such as tube flaring and flanging technology, will expand its application in welded tubes. Therefore, future studies will focus on the FE modeling regarding how to consider effects of welding on residual stresses, welding distortions and microstructure, the inhomogeneous deformation and coordination mechanism of the plastic forming process of tailor-welded tubes, and some end-forming processes of welded tubes, and more comprehensive research on the forming mechanism and limit of welded tubes.     

Al/Ni含能多层膜在Al2O3陶瓷/不锈钢焊接中的应用

采用磁控溅射设备,生长AuSn合金做焊料层、Al/Ni含能多层膜做热量提供层,实现了不锈钢和Al_2O_3间的异质材料自蔓延高温扩散焊。利用SEM、XRD和DSC等测试手段表征AuSn合金和Al/Ni含能多层膜的微观形貌、相成分和放热量;用万能试验机测试焊接接头的力学性能。结果表明,AuSn合金的质量比基本达到80∶20,而多层膜的层状结构清晰,反应热达到1 239 J/g。焊接实验结果表明,仅使用AuSn焊料时,剪切强度仅为46 MPa,在增加Al/Ni含能多层膜后,其剪切强度可达90 MPa,强度提高了约一倍。焊接接头的界面显微形貌和相结构研究表明,剪切强度的增强主要是Al/Ni多层膜提供了额外能量使得界面处的反应剧烈,陶瓷金属化层与中间层的反应加剧,形成了新的反应生成物。     

活塞式航空煤油发动机冷启动性能试验

针对启喷转速、燃油温度、点火能量等影响因素,在一台排量650 mL的单缸试验机上,开展了对航空煤油发动机冷启动性能的试验研究。结果表明:随着启喷转速的提高,启动时间呈现先变短后变长的趋势,启喷转速为1 200 r/min时启动时间最短;燃油温度的提高对冷启动性能和燃烧特性都有提升,在本文试验条件下,燃油温度为50 ℃时即可成功启动;提升点火能量对火核形成和火焰传播都有积极影响,可显著缩短启动时间,但当点火能量增大到75 mJ之后,其改善作用已不明显。