Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

基于混合优化的运载器大气层内上升段轨迹快速规划方法

针对运载器大气层内的最优轨迹快速规划问题,提出一种将求解最优控制问题的间接法与直接法相结合的混合优化方法。首先,基于最优控制问题的一阶必要条件,将运载器大气层内的三维最优上升问题转化为Hamiltonian两点边值问题;然后,采用直接法中能以较少的节点获得较高求解精度的Gauss伪谱法进行求解,提高算法的求解效率;最后,采用真空解析解初值及密度同伦技术,解决初值猜测与算法收敛困难的问题。仿真结果表明,混合优化算法能够准确、快速地对运载器大气层内的最优上升轨迹问题进行求解,并在计算精度与效率上均优于间接法,可应用于运载器的轨迹在线规划与闭环制导。     

飞翼无人机3种保形进气口进气道气动与隐身综合特性对比

基于飞翼布局无人机隐身与结构装载布置要求,保形设计了3种进气口形状的背负式S弯进气道,按照进口投影截面形状上、下底之比顺序排列,分别为三角形、梯形和矩形.利用数值模拟方法对无人机内外流场耦合流动进行计算分析,且基于射线弹跳(SBR)法对进气道电磁散射特性进行仿真研究,获得了飞翼无人机3种进气道的气动与隐身综合特性.研究结果表明:①矩形进气道模型升阻和纵向力矩特性表现均最好;②3种 进气道模型按顺序排列总压恢复系数逐渐增大,畸变指数逐渐减小,进气道沿程气流也逐渐顺畅,矩形进气道模型进气道内流特性最优;③0°迎角下3种进气道模型雷达散射截面(RCS)均值基本呈现先增大后减小的特征,进气道终端开放时矩形进气道模型隐身性能最好,而终端短路时三角形进气道模型隐身效果更优异.      

旋转机翼悬停气动特性研究

鸭式旋转机翼(CRW)是一种先进的高速直升机方案,旋翼同时也是机翼,是其最关键气动部件之一。采用结构分区拼接网格技术进行空间离散,分区建立参考系,通过求解多重参考系下的N-S方程来计算旋翼流场,首先以传统的Caradonna-Tung实验旋翼的亚、跨声速悬停流场分析为例验证该方法的可靠性,进而采用该方法对旋转机翼悬停流场进行了数值计算,旋翼拉力计算值和地面实验值吻合较好,结果分析表明旋转机翼的悬停流场有着不同于传统旋翼的流场特性。     

采用排间界面静压约束伴随方法的多级压气机叶片优化

为解决伴随优化应用在多级压气机中出现的优化工况点漂移问题,在前期薄层N-S方程伴随方法基础上,对目标函数——出口熵增不仅施以质量流量、总压比约束,还添加排间界面静压展向分布作为新的约束条件.以某5级压气机为对象,对其中第1级转、静叶分别在首1.5级和全5级压气机环境下进行了优化.结果表明,施加排间界面静压展向分布约束能够显著解决优化工作点漂移问题,优化后5级压气机的效率提高0.4个百分点.      

S形进气道锤击波荷载特性分析

利用基于改进的延迟分离涡模拟（IDDES）方法,对亚声速和超声速来流条件下某S形模型进气道进行了非定常计算,研究了发动机喘振所产生的瞬时高压波形对锤击波传播规律的影响.结果表明:锤击波产生后沿进气道迅速向前传播,运动过程中锤击波的运动速度基本保持不变,但强度不断增强.同时受气流离心力的影响,S形进气道弯曲段半径较大一侧壁面受到的锤击波气动荷载值更大.发动机喘振所产生的瞬时高压的加载梯度增加使得锤击波传播速度及强度增强,而压力卸载方式对锤击波强度的影响不明显.在亚声速和超声速来流条件下,增加瞬时高压峰值均使得锤击波荷载强度显著增强,并近似符合二次函数分布规律,而且超声速来流条件下锤击波强度较亚声速来流更强.      

基于响应面法的短距/垂直起降飞机近地面升力损失

建立了短距/垂直起降(S/VTOL)飞机近地面升力损失的流场计算模型.通过数值模拟得出特定升力布局的飞机近地面状态各工况的升力损失.采用响应面法获得了飞机升力损失关于喷管落压比（NPR）、来流速度及飞机高度的2阶响应曲面函数及显著影响飞机升力损失的关键因素.并分析了喷管落压比、来流速度及飞机高度对飞机升力损失的交互影响作用,优化得出给定工况范围内升力损失最小的工作点.研究表明:仅考虑单因素影响时,升力损失随高度、落压比的增大而减小,随来流速度的增大而增大;考虑两因素交互作用时,高度与落压比及来流速度与落压比对升力损失存在交互影响,而高度与来流速度对升力损失无交互影响;优化获得的升力损失最小的工作点是飞机距地面高度为9D（D为喷管直径）、喷飞机高度为3、来流速度为0m/s,此时的升力损失为1.3%.      

二氧化碳在RP-3航空燃油中溶解度实验测定

以国产实际使用并含有添加剂的RP-3号燃油为研究对象,测量了燃油在不同温度下的密度,搭建了压力降落法实验装置,测定了5~40℃温度及3组不同压力范围下,CO2在RP-3号燃油中的溶解度,采用ASTM D2780-92标准中提供的相对密度法对溶解度进行了计算并与实验值进行了比较.结果显示:计算值与实验值有很大偏差,且随着温度上升及压力下降,该偏差增加,最大相对偏差可达到106%.根据实验值,对ASTM D2780-92中的阿斯特瓦尔德系数计算公式进行了线性修正,修正后计算的溶解度和实验值误差在10%之内.该研究结果可为绿色惰化的设计提供参考依据.      

用于压气机流动计算的3种模型比较

为了更好地对压气机流动进行模拟,在课题组自行开发的结构化有限体积解算器上实现了用于压气机流场计算的混合平面法、谐波平衡法及相滞后法.以NASA Stage 35为例,对3种方法的计算结果进行了比较分析.结果表明:相滞后法的计算精度最高,混合平面法的计算精度最低;相滞后法与半环的双时间推进法结果相近,计算速度提高了20倍;相比混合平面法,谐波平衡法能准确地模拟动静叶间的非定常干涉及进出口参数变化;在谐波阶数达到5阶后,谐波平衡法计算得到的结果不随阶数变化,且与相滞后法的结果基本吻合;混合平面法的计算效率远高于另外两种方法,相滞后法与谐波平衡法在谐波阶数为5阶时的计算效率相当.