全文获取类型
收费全文 | 1837篇 |
免费 | 328篇 |
国内免费 | 461篇 |
专业分类
航空 | 1588篇 |
航天技术 | 305篇 |
综合类 | 375篇 |
航天 | 358篇 |
出版年
2024年 | 7篇 |
2023年 | 29篇 |
2022年 | 56篇 |
2021年 | 66篇 |
2020年 | 71篇 |
2019年 | 92篇 |
2018年 | 92篇 |
2017年 | 105篇 |
2016年 | 105篇 |
2015年 | 82篇 |
2014年 | 116篇 |
2013年 | 108篇 |
2012年 | 121篇 |
2011年 | 156篇 |
2010年 | 110篇 |
2009年 | 132篇 |
2008年 | 111篇 |
2007年 | 106篇 |
2006年 | 104篇 |
2005年 | 77篇 |
2004年 | 84篇 |
2003年 | 59篇 |
2002年 | 53篇 |
2001年 | 59篇 |
2000年 | 49篇 |
1999年 | 44篇 |
1998年 | 54篇 |
1997年 | 46篇 |
1996年 | 60篇 |
1995年 | 40篇 |
1994年 | 43篇 |
1993年 | 45篇 |
1992年 | 25篇 |
1991年 | 30篇 |
1990年 | 30篇 |
1989年 | 33篇 |
1988年 | 15篇 |
1987年 | 7篇 |
1986年 | 4篇 |
排序方式: 共有2626条查询结果,搜索用时 62 毫秒
861.
862.
863.
弹流润滑螺旋锥齿轮热摩擦行为分析 总被引:1,自引:1,他引:1
针对直升机主减速器中的高速重载螺旋锥齿轮,建立了点接触热弹流润滑分析数学模型,包括Reynolds方程、能量方程和膜厚方程等,采用数值方法求解弹流润滑状态下的齿面摩擦因数.模型中考虑了润滑油黏度和密度随压力、温度的变化,并通过轮齿承载接触分析(LTCA)获得齿面真实载荷和卷吸速度、相对滑动速度等运动学变量.基于真实齿面点建立了螺旋锥齿轮单齿模型,考虑滑动摩擦生热和不同表面上的热边界条件,通过有限元稳态热分析和瞬态热分析得到了轮齿本体温度场和接触点瞬时闪温,并与现有文献和算例齿轮台架试验结果进行对比. 相似文献
864.
865.
866.
867.
时域法在压气机转子气动弹性计算中的应用 总被引:2,自引:1,他引:2
发展了用于三维叶轮机气动弹性计算的软件系统AEAS(aeroelastie analysis system).该系统采用时间推进法求解转子叶片的瞬态位移及动应力,以模拟压气机转子中的气动弹性现象,AEAS主要应用于强迫响应分析和颤振分析,强迫响应分析中,在坎贝尔图上共振点对应的工况下,在转子叶片上施加周期性变化的非定常... 相似文献
868.
869.
利用Ansys有限元软件,采用纤维随机分布模型,对在环境温度t=80℃、相对湿度RH=90%条件下的芳纶纤维/环氧树脂复合材料吸湿后的水分分布进行了模拟计算,计算结果与从材料吸湿实验中所得到的结果基本一致。根据模拟计算得到的水分浓度场对复合材料内部的吸湿应力进行了研究。结果表明:有限元方法可以比较准确地模拟复合材料在湿热环境下的水分吸收过程;复合材料内的水分浓度随老化时间延长而增大,吸湿应力也随之升高,在纤维和基体界面处的应力最大,可达50 MPa以上。 相似文献
870.
Forming Characteristics of Al-alloy Large-diameter Thin-walled Tubes in NC-bending Under Axial Compressive Loads 总被引:2,自引:0,他引:2
Tube thinning control without wrinkling occurring is a key problem urgently to be solved for improving the forming qualities in numerical control (NC) bending processes of large-diameter Al-alloy thin-walled tubes (AATTs). It may be a way solving this problem to exert axial compression loads (ACL) on the tube end in the bending. Thus, this article establishes a three-dimensional (3D) elastic-plastic explicit finite element (FE) model for the bending under ACL and has its reliability verified. Through a multi-index orthogonal experiment design, a combination of process parameters, each expressed by a proper range, for this FE model is derived to overcome the compression instability on tube ends. By combining the FE model with a wrinkling energy prediction model, an in-depth study is conducted on the forming characteristics of large-diameter AATTs with small bending radii and it can be concluded that (1) The larger the tube diameters and the smaller the bending radii, the larger the induced tangent tension stress zones on tube intrados, by which the tube maximum tangent compression stress zones will be partitioned in the bending processes; thus, the smaller the ACL roles in decreasing thinning degrees and the larger the compression instability possibilities on tube ends. (2) The tube wrinkling possibilities under ACL are larger than without ACL acting in the earlier forming periods, and smaller in the later ones. (3) For the tubes with a size factor less than 80, the ACL roles in decreasing thinning degrees are stronger than in increasing wrinkling possibilities. 相似文献