一种温度动态调节方法及其动态性能仿真研究

航空气源模拟试验台主要用于模拟不同飞行状态时发动机给空气管理系统的供气,由于飞机爬升、降落时发动机供气参数会急剧变化,因此航空气源模拟试验台需具备动态能力.基于一种温度动态调节方法,在合理简化的基础之上采用NHT方法对其温度动态性能进行了仿真研究,仿真结果表明该温度动态调节方法能够满足温度动态性能需求,对动态航空气源模拟试验台的设计选型有较高的参考价值.     

Observations of a quasi-90-day oscillation in the MLT winds and tides over an equatorial station using meteor radar winds

An evident signature of a least studied quasi-90-day oscillation is found in the winds and tides in the MLT from an equatorial station, São João do Cariri (7.4°S, 36.5°W). The oscillation is found to appear mainly in certain intervals with small but appreciable seasonal (fourth harmonic of annual oscillation) contribution. The maximum amplitude of the oscillation is found to be around 10 m/s in the zonal wind. The enhancement peak of the oscillation exhibits downward movement indicating a plausible role of upward moving waves/tides in carrying its imprint from below to the MLT. Similar oscillation feature in the tropospheric zonal wind and ozone may imply its lower atmospheric origin as a component of the intraseasonal oscillation (ISO) that moves upward by modulating the tides. Subsequently, the propagating tides (mainly semidiurnal) are enhanced by the ozone in the stratosphere through absorption of solar UV radiation and finally manifest the oscillation in the MLT. Consistency of the present findings with the past investigations are observed in some aspects of the oscillation, whereas existing mismatches in others are believed to be due to geophysical variability depending on space and time among various locations on the globe.     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

可变形翼战术导弹飞行动力学联合仿真研究

基于集中质量假设发展的一套适于可变形翼导弹的多体运动模型,以附加惯性项及快变气动参数的形式来反映弹翼变形对导弹动态特性的影响,涉及交叉求解不同弹翼外形对应的气动特性及运动方程.由此提出的一种基于Missile DATCOM与MATLAB/SIMULlNK的联合仿真方法,应用于典型轴对称导弹的变翼动态特性研究中,快速有效...     

温度对飞机燃油射流泵工作特性影响

建立了射流泵数学模型,采用数值计算方法对其工作特性进行了模拟,搭建了实验台,采用RP-3燃油,通过实验数据验证了模型的正确性.在此基础上,分别选择了RP-3和JET-A两种燃油,计算了从-40℃~40℃温度下,不同操作压力对射流泵流量比的影响.结果表明:燃油温度高于0℃时,温度对射流泵工作特性影响并不明显,随着温度的降低,射流泵性能与标准温度下（20℃）偏差越来越大,且压比越高此偏差越明显.当温度高于0℃时,采用RP-3和JET-A燃油性能相差不大,RP-3燃油性能略优于JET-A燃油,但是在低温下,RP-3燃油性能远高于JET-A燃油.因此当燃油温度较低且压比较高时,必须充分考虑温度对射流泵特性的影响.      

Nonlinear dynamic modeling of a helicopter planetary gear train for carrier plate crack fault diagnosis

Planetary gear train plays a significant role in a helicopter operation and its health is of great importance for the flight safety of the helicopter. This paper investigates the effects of a planet carrier plate crack on the dynamic characteristics of a planetary gear train, and thus finds an effec-tive method to diagnose crack fault. A dynamic model is developed to analyze the torsional vibra-tion of a planetary gear train with a cracked planet carrier plate. The model takes into consideration nonlinear factors such as the time-varying meshing stiffness, gear backlash and viscous damping. Investigation of the deformation of the cracked carrier plate under static stress is performed in order to simulate the dynamic effects of the planet carrier crack on the angular displacement of car-rier posts. Validation shows good accuracy of the developed dynamic model in predicting dynamic characteristics of a planetary gear train. Fault features extracted from predictions of the model reveal the correspondence between vibration characteristic and the conditions (length and position) of a planet carrier crack clearly.     

燃料分级对旋流火焰的动态特性影响研究

为深入研究分级旋流火焰特性,以分级旋流模型燃烧室为研究对象,对四个不同燃料分级比(Rf)条件下的分级旋流火焰进行了数值研究,在时均燃烧场特性分析的基础上进一步对燃料分级比为1和3两个工况进行了基于壁面建模的大涡模拟(WMLES)研究。结果表明:燃料分级比的改变会影响中心回流区(CRZ)的长度和宽度。燃烧室中截面的散点分布图能够显示出不同燃料分级比条件下的燃烧特征。燃料分级比为1时,燃烧室剪切层仅存在零散的涡破碎区;而燃料分级比为3时,伴随涡破碎区还出现了单螺旋分支进动涡核(PVC)。通过FFT变换获得的燃烧室内剪切层速度能谱主频与进动涡核的旋转频率相同,表明内剪切层速度脉动的产生与进动涡核有关。另外进动涡核会使流场内的燃料分布和燃烧模式发生周期性的变化,进而影响燃烧过程。调整燃料分级比在1附近,能够使分级火焰达到稳定燃烧降低排放的目标。     

幂律型流体撞击射流破碎特性直接数值模拟

凝胶推进剂的双股射流撞击雾化广泛应用于液体火箭发动机的燃烧室中,其破碎特征及雾化效果直接影响燃烧效率。为探究雾化特性的发展规律,采用直接数值模拟DNS方法,对射流速度为100m/s的剪切稀化非牛顿液体正交撞击产生的雾化特征、液体表面积、表面波、涡特性以及非牛顿特性开展研究。结果表明,射流下形成的雾化流场迅速扩张形成液膜,液膜两侧边缘破碎成大量的液丝与液滴,核心部分产生撞击波后在气体力的作用下逐步发展为带有凸起和褶皱的不稳定表面波,其撞击波波长最大可达2.46倍射流直径。液体表面积不断增长,但无量纲表面积总体呈现先下降再上升的趋势。气体中的涡量分布则分为有序附着区和无序爆炸区两类,并且涡量主要集中分布于气相区域。此外,射流撞击时产生强剪切使该液体内部的粘性系数下降,最低仅为初始粘性系数的0.3倍。     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。