ZSGA?2型重力敏感器关键技术分析与试验验证

与国外主流海洋重力仪相比,国产海洋重力仪的分辨率低一个数量级,这制约了国产海洋重力仪的应用。针对国产海洋重力仪亟需提高分辨技术的需求,根据ZSGA-2型重力敏感器的工作原理,建立了弹性系统的力学模型,并开展了样机的静态性能测试。测试结果表明,经零位漂移和大地固体潮汐修正后的静态精度达到了0.03mGal,样机随重力仪进行楼层高差测量的重复性为0.15mGal。该型重力敏感器的分辨率已经达到了国外同类产品的技术水平,并具备了一定的动态适应性,为该型高分辨率零长弹簧重力敏感器开展高动态环境适应性技术研究奠定了坚实基础。     

MEMS惯测技术在管道测绘系统中的应用

针对小口径管道的测绘问题,提出了一种MEMS惯测装置在小管道测绘系统中应用的方法,直接利用地标点信息为MEMS惯测装置装订初始方位,采用因子图理论对惯性/里程计组合导航信息进行处理,通过后续处理对装订误差进行修正,解决了MEMS惯测装置无法完成初始对准的问题。给出了惯性/里程计组合导航的因子图以及和积算法递推公式,并通过牵引试验对所提方法进行了验证。试验结果表明,提出的应用方法能够有效解决小口径管道的测绘问题,在100m间隔的路标点条件下,单边定位精度能够达到5cm。     

基于工况/场景的飞机系统试验验证方法

描述了一种飞机系统在试验室系统综合或全机级环境下进行设计验证的方法和过程。首先定义系统需求所在工况/场景,然后根据功能基线,确定工况发生的阶段以及完成此工况需参与的系统范围和构型,从而形成具体的试验步骤,进而通过试验来判断系统的响应是否满足上一级需求。     

工程意义上的高斯脉冲信号不失真采样分析

基于高斯脉冲信号的时频域特征,分析其采样条件。针对高斯脉冲信号这种非周期信号采样的特殊性,指出高斯脉冲信号采样还需满足峰值采样条件,并对不同采样点数下峰值误差能够达到最小值的概率进行建模。理论分析和仿真结果表明,按照所提出的采样条件进行采样,能够保证高斯脉冲信号采样的峰值误差最小,同时所提出的概率模型能够比较准确地估计出在不同采样点数下峰值误差能够达到最小值的概率。     

基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一,为此,提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵,获取试验过程中相机实时位姿和标记点物方空间位置坐标,应用坐标旋转关系,完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系,因此,当标记点不满足共面条件时,可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后,迎角实测数据的测量准度在0.01°以内,精度不超过0.012°。本文方法易于实施,工程实用价值强。     

基于G-M制冷机的大尺寸冷屏设计方法

介绍了基于Gifford-Mcmahon (G-M)制冷机的大尺寸冷屏的设计方法。该低温冷屏配合真空环境模拟室共同使用,为遥感卫星的星载遥感器等部件的红外定标试验提供20K的低温冷背景。该冷屏采用5台G-M制冷机进行制冷,外形尺寸达到1m×1m,是目前国内同类型冷屏中尺寸最大的。详细介绍了冷屏在容器内的安装布置、冷缩时的补偿等结构设计方法、冷屏的表面温度分布以及降温时间等计算分析。成功解决了大尺寸冷屏在低温环境下的冷缩补偿难题,试验结果表明:冷屏主要测点温度为15K,温度均匀性误差为±1K,达到并超过设计要求。      

带止口法兰连接结构刚度特性对结构振动影响

对带有止口的法兰连接结构刚度特性进行了数值仿真研究。使用有限元软件ANSYS分析了带有止口的法兰连接结构的迟滞特性。通过对止口接触面的变形-滑移机理分析,使用一个詹金斯单元和一个弹簧单元并联模拟法兰的一个扇区,并基于法兰弯曲变形时每个扇区的不同状态建立了整个法兰结构的弯曲刚度简化模型,并对该简化模型进行了仿真,该简化模型能够较准确地模拟带止口法兰连接结构的刚度特性。基于简化模型和梁单元建立了简化转子结构模型,分析了带有止口的法兰连接结构对转子稳态动力学响应的影响。结果表明带有止口的法兰连接结构的迟滞特性能够影响峰值频率,随着止口过盈量的增加,响应峰值显著降低,具有较好的振动抑制效果。      

基于二阶滑模算法的永磁电机直接转矩控制

针对传统直接转矩控制(DTC)方法低速控制精度差、转矩脉动大、开关频率不稳定等问题,提出了一种基于二阶滑模控制的永磁电机DTC方法。该控制方法基于二阶滑模控制原理,将传统磁链控制器与转矩控制器以滑模控制器替代,对空间电压进行矢量调制,提高了开关频率的稳定性,获得了良好的动态稳定性,改善了电机输出性能。仿真与试验结果表明,该控制方法能够有效减小电流脉动与转矩脉动,同时提高了控制系统的抗干扰能力,实现了电机的快速动态响应,具有较强的鲁棒性能。     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.