CVI反应器内部气体流场的有限元模拟及优化设计

采用有限元计算方法,研究了CVI反应器内部的流场特征.对于形状简单的构件,构件的放置方式和阵列对气体的流动状态具有显著的影响.与横向阵列相比,纵向阵列能充分保证构件沿其长度方向流场均匀性,减小回流现象;在反应器中,随着纵向阵列试样数量的增加和分布均匀性的提高,气体流动速度增大,流场均匀性提高.减少反应器内部的自由空间,是提高流场品质和化学气相沉积效果的关键.基于减少反应器内部的自由空间的原则,针对杯形复杂构件,提出了通过加入与其几何形状相适应的导流板工装,有效避免了在构件内部和外部形成回流区,实现流场的优化设计.     

超燃冲压发动机缩比燃烧室流场数值模拟

为了采用二维N-S方程来研究带有垂直喷射的三维问题,即拓展二维模型的适用范围,提出了一种针对喷射的简化模型,即采用源项加质来近似模拟喷射的质量添加。为了验证这种简化的可行性,针对文献中的实验条件进行了对比计算。结果表明,数值模拟与实验点符合得较好。运用以上简化模型,对放置在自由射流实验台上的缩比超燃冲压发动机燃烧室流场,采用五组元单步反应模型进行了数值模拟,得到了各主要气动参数及组分质量分数的分布,表明,根据数值模拟所得到的壁面静压值与实验壁面压力符合得较好。      

Galactic Wind: Mass Fractionation and Cosmic Ray Acceleration

The dynamical and chemical effects of the Galactic Wind are discussed. This wind is primarily driven by the pressure gradient of the Cosmic Rays. Assuming the latter to be accelerated in the Supernova Remnants of the disk which at the same time produce the Hot Interstellar Medium, it is argued that the gas removed by the wind is enriched in the nucleosynthesis products of Supernova explosions. Therefore the moderate mass loss through this wind should still be able to remove a substantial amount of metals, opening the way for stars to produce more metals than observed in the disk, by e.g. assuming a Salpeter-type stellar initial mass function beyond a few Solar masses. The wind also allows a global, physically appealing interpretation of Cosmic Ray propagation and escape from the Galaxy. In addition the spiral structure of the disk induces periodic pressure waves in the expanding wind that become a sawtooth shock wave train at large distances which can re-accelerate “knee” particles coming from the disk sources. This new Galactic Cosmic Ray component can reach energies of a few×10¹⁸ eV and may contribute to the juncture between the particles of Galactic and extragalactic origin in the observed overall Cosmic Ray spectrum.     

Effects of the Fabrication Processes of NC-Si:H Films on Their Mechanical Properties

Studies of nanoindentation were performed on nc-Si:H films to evaluate the effects of the fabrication processes on their mechani-cal properties. It is observed that with the decrease of the SiH4 contents, the grain size of the films increases gradually, and as does the crystalline volume fraction. The smaller the grains become, the more homogeneous the films, and the more even the hardness as well as the modulus will be. The hardness and the modulus will increase with the substrate’s temperature rising. The hardness and the modulus of the nc-Si:H films on the Si substrate prove to be higher than those on the glass substrate given the same technology parameters. How-ever, the films on the glass substrate appear to be more homogeneous.     

燃料组分差异对贫油熄火边界的影响

为了推进替代燃料的多元化,扩大航空燃料的组分分布。以标准航空煤油为基准,研究了柴油和高沸点费托油对燃烧室贫油熄火边界的影响。实验采用单头部燃烧室,通过改变燃烧室进出口压力,研究其熄火边界的变化规律,并分析了其与理化性质和组成的关联关系。结果显示在220kPa的出口压力下,航空煤油的熄火性能略优于另外两种燃油,高沸点费托油相比航空煤油熄火边界窄5%,而在140kPa的低压条件下,高沸点费托油的熄火边界相比航空煤油拓宽了8%。分析得到整体上低沸点烷烃和直链烷烃的熄火性能较好。      

整体叶盘弹性磨具抛光轨迹关键规划方法

为使得弹性磨具(砂布轮)在抛光中和叶片型面有效切合,提高抛光质量和抛光效率,研究了弹性磨具抛光轨迹规划方法,给出了抛光行距、抛光步长、刀轴矢量的计算方法。该抛光轨迹规划方法使得柔性主轴机构在抛光过程中保持合理的位姿,确保弹性磨具不仅与叶片型面有效贴合,而且使得弹性磨具抛光力方向与抛光点位法矢方向基本一致。试验结果表明:抛光后叶片表面粗糙度小于0.4μm,叶型轮廓度在公差范围内,能够满足整体叶盘叶片型面抛光要求。     

钝体稳定射流火焰的火焰面模型数值研究

基于稳态火焰面(SLFM)和交互式非稳态欧拉颗粒火焰面(EPFM)模型对Sydney大学CH4/H2钝体稳定湍流扩散火焰行了数值研究,采用修正的雷诺应力模型(RSM),同时对两种不同规模的甲烷详细化学反应动力学机理进行研究,比较了燃烧模型和反应机理对湍流火焰结构、活性自由基以及氮氧化物预测精度的影响,与实验数据对比结果表明:两种反应机理得到的温度场和主要组分分布基本相同;SLFM模型能对速度场和标量场的分布进行较为准确预测,采用EPFM模型修正后,部分区域OH预测结果更加靠近实验结果;采用EPFM模型对SLFM模型耦合GRI-Mech 211的计算结果修正后,NO量级降低近2倍,预测精度明显改善,与实验结果实现较好的符合,验证了化学反应动力学机理以及非稳态效应对氮氧化物预测精度的影响。     

Influence of fuel injection position and equivalent mixture ratio on chemical non-equilibrium effects of single expansion ramp nozzle

Chemical non-equilibrium flow was investigated for the scramjet single expansion ramp nozzle(SERN) with a strut-based liquid-kerosene-fueled combustor.Two-dimensional Reynolds-averaged Navier-Stokes(RANS) equations were solved with the species conservation equation for continuous phase and the renormalization group(RNG) k-ε turbulence model.Lagrangian discrete-phase model was analyzed for liquid-kerosene droplets behavior in the supersonic stream.Combustion was simulated by kerosene surrogate fuel's 10-species and 13-step reduced reaction kinetics mechanism with use of Arrhenius's laminar finite rate model.Parametric studies were carried out to estimate the influence of different fuel injection positions and equivalent mixture ratios on the SERN chemical non-equilibrium effects.Numerical calculation results show that the strut-based combustor enables convenient modeling of various SERN entry conditions,which is similar with many preceding investigations,by changing the injector strut position and controlling the mass flow rate of each injector.Chemical non-equilibrium effects function in the whole SERN,especially in the initial flow expansion region,leads to obviously higher SERN performance of the non-equilibrium flow than that of the frozen flow.Furthermore,the distributed fuel injection pattern plays a significant role in enhancing the combustion efficiency in combustor,but weakening the chemical non-equilibrium effects funciton in SERN.Additionally,while the equivalent mixture ratio increases,the SERN thrust coefficient and lift coefficient rise gradually,and the increment of non-equilibrium flow in relation to frozen flow becomes higher as well.To be specific,the equivalent mixture ratio is 0.6,the maximum increment of thrust coefficient and lift coefficient are 11.6% and 25% respectively.      

增材制造异形波导管内腔的磨粒流抛光方法研究

针对磨粒流抛光异形波导管内球面欠抛的问题,通过设置仿形芯模引导磨料流经内球面,完成内球面的抛光.利用Fluent对不同仿形芯模与波导管内腔形成的流道模型进行流体仿真,对比分析等效壁面的流速、压力以及壁面剪切应力.仿真结果表明,芯模球径越大,越有利于改善内球面的加工质量.采用球径9mm的仿形芯模进行磨粒流抛光试验,波导管...     

光纤连接器端面研磨的技术关键

简要地介绍了连接器的生产中最关键的研磨工艺，对研磨工艺流程，研磨质量跟踪表和研磨质量指标通过实际生产过程进行研究。而且利用跟踪记录的研磨数据，并根据研磨质量的指标，找出一套最佳的研磨工艺。从而生产出高质量的连接器。