超燃冲压发动机多凹腔串联燃烧室阻力研究

在直连式试验台上,采用等截面燃烧室对多个凹腔同侧串联布置的燃烧室的阻力进行了试验研究。分析了凹腔深度分别为10、15和20mm,凹腔长深比分别为5和7的不同凹腔组合、凹腔顺序、凹腔距离和凹腔数目在不同燃料当量比下的燃烧室内阻。研究结果表明,在同一燃料当量比下,燃烧室内串联凹腔数目越多,阻力越大,单个阻力较大的凹腔组合后总阻力较大;燃料喷射方式和当量比对燃烧室阻力变化规律影响较大,在小当量比时氢气燃烧放热将可能增加燃烧室内阻;相同当量比和燃料喷射方式下,氢气比煤油燃烧时阻力大;在合适的当量比和燃料喷射方式下煤油燃烧时组合凹腔可能产生正推力。     

单凹腔驻涡燃烧室值班油气匹配研究

为开展单凹腔驻涡燃烧室值班油气匹配思路研究,采用试验研究方法,在燃烧室进口压力、温度以及马赫数分别为0.101MPa、487 K、0.25,燃料为航空煤油的条件下开展试验。试验中主要研究了4种不同总油气比FAR =0.0093、0.0124、0.0155、0.0186,以及对应相同总油气比下不同凹腔油气匹配思路。即通过更改凹腔进气结构,在总油气比一定的情况下,调节凹腔当量比Φca。研究结果表明：凹腔内的油气匹配对燃烧效率影响显著。当总油气比小于0.0155时,不同凹腔当量比的燃烧效率均随总油气比增加而增加;总油气比大于0.0155后,不同凹腔当量比的燃烧效率随油气比的变化规律有所差异,当凹腔富油时,燃烧效率减少;当凹腔由贫转富时,燃烧效率缓慢上升;进一步研究发现,凹腔当量比小于1.4时,不同当量比的燃烧效率随总油气比增加均有所增长,在凹腔当量比大于1.4后,效率有下降的趋势。因此,在总油气比相同,仅凹腔供油的工作状态,凹腔局部富油时的燃烧效率高于当量比为1时的燃烧效率。凹腔当量比1.4为仅凹腔供油燃烧的最佳当量比。     

旋转盘腔轴向通流的压降和温升数值研究

为获得旋转雷诺数对盘腔轴向通流温升和压降的影响,对轴向通流雷诺数(Re_x)恒定为1.0′10^₅、旋转雷诺数(Re_w)在0~5.31′10^₆之间、绝热边界下的流动进行了数值模拟,从流场特征、盘面绝热温升以及轴向通流压降和温升等三个方面进行了分析。研究表明,旋转雷诺数对于盘腔内部和轴向通流的流动均具有显著影响;尽管是绝热盘面,但是由于高速旋转的黏性耗散作用引发盘腔内气流的温升,由温度差引起的浮升力对于盘腔内流动和盘面温度分布的影响也是不可忽略的;随旋转雷诺数增大,轴向通流出口温度相对进口温度的温升急剧增大,在旋转雷诺数小于2.5′10^₆时,轴向通流相对温升系数在0.01以内,当旋转雷诺数大于4.5′10^₆时,轴向通流相对温升系数达到0.04以上。     

Preliminary experiment on spontaneous ignition performances of cavity-based strut flameholder

The thermal-structural response and low cycle fatigue life of a three-dimensional (3D) channel wall nozzle with regenerative cooling were numerically investigated by coupling the finite volume fluid-thermal method, nonlinear finite element thermal-structural analysis and local strain methods. The nozzle had a high area ratio (nozzle exit area divided by throat area) under cyclic working loads. Parametric studies were carried out to evaluate the effects of channel structural parameters such as channel width, channel height, liner thickness and rib width. Results showed that the integrated effects of three-dimensional channel structure and load distribution caused serious strain, which mainly occurred at the intersectant regions of liner wall on the gas side and the symmetric planes of channel and rib. The cooling effect and channel structural strength were significantly improved as the channel width and height decreased, leading to substantial extension of the nozzle service life. On the other hand, the successive decrease in liner thickness and rib width apparently increased the strain amplitude and residual strain of channel wall nozzle during cyclic work, significantly shortening the service life. The present work is of value for design of the channel wall nozzle to prolong its cyclic service life.      

用于光纤F-P声压传感器的直流补偿解调技术研究

提出了一种改进的双腔直流补偿技术，用于解调非本征法布里-珀罗干涉(EFPI)光纤传感器，以消除腔长差与入射光波长相匹配的要求。通过消除直流分量和校准信号相位，可以从具有任意相位差的原始信号中获 得两路正交信号。通过理论仿真，制作了具有不同腔长差的EFPI光纤传感器，对所提出的方法进行了试验验证。 结果表明，该方法在解调双 F P腔 EFPI传感器时，不需要保证初始相位差恒定，且对腔长漂移不敏感，具有良好的 稳定性和实用价值。     

Aerodynamic characteristics of store during lateral jet assisted separation from cavity using free drop technique

Aimed at the problem of store separation from internal cavity, this paper innovatively puts forward a separation scheme of using lateral jet to assist store safe separation. The jet ensures that the store is continuously subjected to down head moment during separation, so as to ensure safe separation. The wind tunnel free drop test technique with lateral jet is established, which can ensure that there is no support interference in the motion process of the store and more truly simulate the motio...     

Multi-scale simulation model of air system based on cross-dimensional data transmission method

The Secondary Air System (SAS) plays an important role in the safe operation and performance of aeroengines. The traditional 1D-3D coupling method loses information when used for secondary air systems, which affects the calculation accuracy. In this paper, a Cross-dimensional Data Transmission method (CDT) from 3D to 1D is proposed by introducing flow field uniformity into the data transmission. First, a uniformity index was established to quantify the flow field parameter distribution characteristics, and a uniformity index prediction model based on the locally weighted regression method (Lowess) was established to quickly obtain the flow field information. Then, an information selection criterion in 3D to 1D data transmission was established based on the Spearman rank correlation coefficient between the uniformity index and the accuracy of coupling calculation, and the calculation method was automatically determined according to the established criterion. Finally, a modified function was obtained by fitting the ratio of the 3D mass-average parameters to the analytical solution, which are then used to modify the selected parameters at the 1D-3D interface. Taking a typical disk cavity air system as an example, the results show that the calculation accuracy of the CDT method is greatly improved by a relative 53.88% compared with the traditional 1D-3D coupling method. Furthermore, the CDT method achieves a speedup of 2 to 3 orders of magnitude compared to the 3D calculation.