高导电硅橡胶材料的性能

首先通过平行对比了三种填充不同导电填料的硅橡胶材料的拉伸强度、扯断伸长率、恒定压缩永久形变、导电性及屏蔽性能,优选出镀银铝粉作导电填料;考察了镀银铝粉用量对硅橡胶材料的拉伸强度、伸长率、压变、微观形貌、导电性能的影响,最终确定镀银铝粉的填充体积分数为55%;结合导电橡胶制品对使用寿命的需求,进一步深入研究了导电硅橡胶材料在自然平贮老化及高温加速老化下的导电性能。结果表明:随老化时间的延长,体积电阻率不断增大,导电性能减弱。自然平贮老化60 d后,材料的体积电阻率基本不变;900d后,体积电阻率由初始值4.6×10-3Ω·cm增大至7.5×10-2Ω·cm。150℃老化30 d后,体积电阻率由初始值增大至9.5×10-2Ω·cm。填充镀银铝粉的导电硅橡胶材料在两种条件下老化后均能保持高的导电性;高温加速老化对导电性能的影响大于自然平贮老化。     

隔离段对二维混压式进气道出口参数的影响

利用Fluent仿真软件,对二维混压式高超音速前体/进气道在设计状态和非设计状态下的性能和流场进行了计算。分析表明,进气道在设计状态下的性能得到了明显的提高。同时,有无隔离段以及隔离段长度对进气道出口参数的影响,文中进行了初步的分析,结果表明:有无隔离段以及隔离段长度对进气道出口总温没有太大的影响;隔离段较短时,进气道出口总压比无隔离段小,但当隔离段长度增大到一定值后,进气道出口总压比无隔离段大;隔离段较短时,进气道出口马赫数比无隔离段大,但当隔离段长度增大到一定值后,进气道出口马赫数比无隔离段小。     

导弹燃气流瞬态温度测量系统设计

介绍了采用蓝宝石黑体腔光纤作为传感器的导弹燃气流瞬态温度测量系统的测量原理、系统组成,阐述了其硬件功能模块设计,给出了软件设计算法及蓝宝石黑体腔光纤高温计的标定方法。     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

轴对称推力矢量喷管载荷变形的控制补偿

研究了温度场和气动载荷联合作用下的轴对称矢量喷管出口面积和偏转角度误差的补偿问题.建立了扩张调节片位姿参数与其悬挂机构尺度之间的关系,导出了悬挂机构关节角位移增量与构件长度增量之间的微分方程,得到喷管出口面积误差和矢量偏转角误差与负载变形之间的解析表达式.利用矢量偏转角度和面积与轴对称矢量喷管转向驱动机构动平台位姿之间的关系,建立了受温度场和气动载荷联合作用下的动平台位姿补偿方程.研究表明,补偿后的矢量偏转角度和面积的相对误差不大于1%.      

气体动压轴承-转子动力系统稳定性及分岔

基于非线性动力学理论, 研究了普通圆柱型径向气体动压轴承支承的转子动力系统的运动稳定性和分岔.建立了气体动压轴承-Jeffcott转子系统的力学模型, 并采用有限元方法逼近非定常气体雷诺方程, 得到任意时刻的气膜力;数值模拟该非线性动力系统的长期行为, 得到了轴颈中心的运动轨迹;并采用轨迹图、相图、分岔图以及功率谱等, 研究了系统的非线性行为以及不平衡响应的稳定性.研究结果表明:该方法对气体轴承中存在的气膜涡动问题能够给予合理的解释.      

燃气轮机滚动轴承故障模式及延寿方法

分析了燃气轮机滚动轴承常见的10种故障模式及其产生原因,研究了相应的延寿方法及其延寿机理。     

某重型燃气轮机放气活门及排气管路的改进设计

针对某重型燃气轮机放气系统放气活门在结构设计上存在的问题,经过分析和论证,提出了改进方案,通过计算验证了该方案可以实施。     

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

中心进气转静盘腔的流量分配特性试验

采用实验方法, 对具有中心进气、两个出口的盘腔系统的流动特性进行了研究.获得了静盘与转盘间隙以及转盘外缘小孔的冷气流量.结果表明:盘面出流孔的流量随总流量或转速的增加而增加, 该流量与总流量的流量比随总流量的增加而降低, 随着转速增加而增加.盘面出流孔数量为原出流孔数量的一半时, 流出流量也近似是原流出流量的一半.