C/ C-PAA 与C/ C-FA 弯曲性能对比

通过PIP工艺制备了C/C-PAA、C/C-FA复合材料,对PAA、FA裂解碳的XRD、浸渍效果以及C/C-PAA和C/C-FA的弯曲强度进行了分析.结果表明:PAA裂解碳的炭质量、浸渍效果较好,C/C-PAA弯曲强度比C/C-FA弯曲强度高34.9％,弯曲模量对比不明显.     

Failure of EB-PVD Thermal Barrier Coatings Subjected to Thermo-Mechanical Loading

Thermal barrier coatings (TBCs) were developed to protect metallic blades and vanes working in turbo-engines. The two-layered structure TBCs, consisting of NiCoCrAlY bond coat and yttria stabilized zirconia (YSZ), were deposited on a cylinder of superalloy substrate by the electron beam-physical vapor deposition (EB-PVD). The failure mechanism of the TBCs was investigated with a thermo-mechanical fatigue testing system under the service condition similar to that for turbine blades. Non-destructive evaluation of the coated specimens was conducted through the impedance spectroscopy. It is found that the crack initiation mainly takes place on the top coat at the edge of the heated zones.     

Investigation on a Sol-gel Coating Containing Inhibitors on 2024-T3 Aluminum Alloy

For a long time, chromate incorporated conversion coatings have been drawn special attention in corrosion protection of air-craft-used aluminum alloys. However,ever-increasing environmental pressures requires that non-chromate conversion coatings be developed because of the detrimental carcinogenic effects of the chromate compounds. In recent years, the sol-gel coatings doped with inhibitors were developed to replace chromate conversion coatings, and showed real promise. A sol-gel coating was prepared and its anti-corrosion behavior was investigated using the potentiodynamic scanning (PDS) and the electrochemical impedance spectroscopy (EIS). It is found that the sol-gel coating obtained by the hydrolysis and condensation of 3-glycidoxypropyltrimethoxysilane (GPTMS) and tetramethoxysilane (TMOS) is prone to form defects if cured at the room temperature, whereas if cured at a higher temperature (100 ℃), these flaws can be avoided. Furthermore, it can be seen that addition of anti-foam agents and surfactants will reduce the faults if cured at the room temperature. Effects of the corrosion inhibitors, CeCl3 and mercaptobenzothiazole (MBT), in the sol-gel coatings on 2024-T3 aluminum alloy were also investigated. Results show that the corrosion resistance of the sol-gel coatings containing CeCl3 proves to be better than that of the pure and MBT added sol-gel coatings by the electrochemical methods.     

M40J/CE/EP复合材料出气性能研究

通过地面环境模拟实验,分析了高模碳纤维/环氧树脂改性氰酸酯复合材料(M40J/CE/EP)的表面元素,研究了高真空加热环境下复合材料的真空出气性能和出气气体成分.结果表明,M40J/CE/EP复合材料的表面主要由C、O、N元素构成;经高真空加热后,复合材料的出气气体成分以小分子挥发物和碳氢化合物电离碎片为主,有可能在空间低温条件下冷凝在航天器的敏感器件表面而造成污染;通过真空出气性能实验测得,M40J/CE/EP复合材料的总质量损失(TML)的平均值为0.27%,收集到的可凝挥发物(CVCM)为0,完全达到出气筛选合格的指标要求.     

γ-射线辐照对碳纤维表面结构以及强度的影响

利用高能射线对碳纤维(CF)表面进行改性是高效、节能和环保的一种技术。研究了60Coγ-射线辐照下,吸收剂量在0~1000kGy时,聚丙烯腈基CF表面形貌及结构的变化。利用原子力显微镜(AFM)观察处理前后CF表面形貌的变化。采用Ram an光谱分析了辐照对CF表面结构的影响,并测定了处理前后CF复丝拉伸强度和不同标距下单丝拉伸强度的变化。结果表明,在0~30kGy剂量处理后的CF表面轴向沟槽数量先增加,ID/IG逐渐增大,石墨微晶尺寸(La)减小;当剂量过大时,沟槽数量减少,沟槽变得又深又宽,ID/IG有所降低,La增加,碳纤维表面结晶度提高。结合双参数W e ibu ll理论,计算处理前后的模数m与La的变化趋势一致,说明小剂量辐照下,对碳纤维表面有细晶化作用,在一定程度上可以提高CF的拉伸强度。随着辐照剂量的增加,促进碳原子的排列更规整,向模量较高的方向转化。     

高浓度颗粒流冲刷条件下硅橡胶和EPDM绝热材料动态烧蚀实验

利用X射线实时诊断技术(RTR)针对硅橡胶和EPDM绝热材料,开展了高浓度颗粒流冲刷条件下动态烧蚀实验研究,成功获得了绝热材料烧蚀表面退移过程的序列图像。研究表明:(1)在本实验条件下,硅橡胶绝热材料颗粒冲刷区域的瞬时烧蚀率在0～2s内迅速增加,2s之后瞬时烧蚀率略有下降并趋于稳定;EPDM绝热材料颗粒冲刷区域的瞬时烧蚀率在0～1s内迅速增加,1s之后瞬时烧蚀率趋于稳定;(2)相同冲刷条件下硅橡胶绝热材料抗颗粒流冲刷性能比EPDM绝热材料差,硅橡胶绝热材料不适合在高过载发动机中应用;(3)高浓度颗粒流冲刷条件下绝热材料的烧蚀率比常规条件下要严重的多,其机理主要是高温颗粒流对炭化层有强烈的机械剥蚀效应和热化学烧蚀作用。实验结果对硅橡胶和EPDM绝热材料烧蚀机理研究及烧蚀建模具有重要参考价值。     

复合材料界面的微观力学行为研究单纤维拉出试验

使用一专门设计的模型制作了碳化硅／玻璃复合材料单纤维拉出试样。利用纤维拉曼峰波九偏移一纤维所受应变的近似线性关系,首先测定纤维热残余应变的分布,随后对伸出玻璃基体外的纤维段施加给定的拉伸应变,沿纤维轴向用拉曼光谱术逐点测定基体内外纤维的应变,最后依据力平衡原理将应变分布转换为界面剪切应力沿纤维轴向的分布。结果表明：在给出一实验参数下,界面传递应力长度为０．１８ｍｍ,最大界面剪切应力的位置在ｘ为０．     

High-temperature oxidation behavior and analysis of impedance spectroscopy of 7YSZ thermal barrier coating prepared by plasma spray-physical vapor deposition

Quasi-columnar structure 7YSZ(yttria stabilized zirconia) thermal barrier coatings(TBCs) are prepared by plasma spray-physical vapor deposition(PS-PVD) onto pretreated and un-pretreated bond coating, respectively. An isothermal oxidation experiment of 7YSZ TBCs is carried out in the atmosphere of 950 °C in order to simulate the high-temperature oxidation process of engine blades. The isothermal oxidation process of 7YSZ thermal barrier coatings is investigated systematically by impedance spectroscopy. The electrochemical physical model and equivalent circuit of columnar 7YSZ coatings are established. Results show that the isothermal oxidation kinetic curve of columnar 7YSZ thermal barrier coatings appears to follow the parabolic law. A pretreatment of bond coating can reduce the growth rate of the thermally grown oxide(TGO) layer, restraining the initiation and propagation of microcracks between YSZ and TGO layers. The oxidation rate constants of 7YSZ coatings with pretreated and un-pretreated bond coating are 0.101×10~(-12) cm~2·s~(-1) and 0.115 × 10~(-13) cm~2 ·s~(-1), respectively. Impedance analysis shows that the content of oxygen vacancies decreases and the density increases after the TGO layer is oxidized for 150 h. In addition, shrinkage microcracks formed by sintering during the oxidation process is the main reason for an increase of the capacitance and a decrease of the resistance in the grain boundary of YSZ.     

不同工件超光滑表面残余应力的测试研究

通过对玻璃、陶瓷、金属3个试件进行超精密加工,使试件表面粗糙度达到纳米级,采用非破坏性的X射线衍射sin2ψ法测量原理对不同试件的残余应力进行了测试研究。结果表明:在本试验条件下,3个试件都只存在残余压应力,并且陶瓷的残余压应力最大,金属残余压应力最小。     

基于差分吸收光谱技术的烟道SO2浓度的测量

利用差分光谱吸收（DOAS）技术，测量大气中痕量污染气体的浓度，是当前环保行业一项热门技术。对此方法适当改进，可以用来监测工业烟道排出的SO2的浓度和排放量，研究了利用DOAS技术测量烟气的测量方法、数据处理以及减小误差的方法，实现了烟气中SO2的在线实时测量。